Summary of Contents for Ferno SA-3BLP-01
- Page 1 CARE & USE MANUAL BUILT-IN & FREESTANDING GRILL BY FERNO GRILLS GOLETA, CALIFORNIA T: 888.800.1688 E: info@fernogrills.com www.fernogrills.com...
- Page 2 WARNING! READ THIS MANUAL CAREFULLY and completely before using your grill to reduce the risk of: 1. Fire 2. Burn hazard, personal injury, or property damage 3. Burned food or unpleasant cooking experiences 4. Unapproved installation or servicing THIS PRODUCT IS DESIGNED FOR OUTDOOR USE ONLY. Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
- Page 3 THIS MANUAL MUST REMAIN WITH THE PRODUCT OWNER FOR FUTURE REFERENCE. This product conforms to ANSI STD Z21.58-2018 and has been tested and approved by Intertek. To obtain replacement parts or service, contact: Ferno Grills Goleta, California Customer Service: (888) 800-1688 or info@fernogrills.com Page | 3...
-
Page 4: Table Of Contents
Natural Gas (NG) Final Checks Troubleshooting Guide o Troubleshooting Quick Reference Guide o Grill Wiring Diagram o Freestanding Model Exploded View Parts Lists o Built-in Model Exploded View Parts Lists Ratings Plate/Serial Number Information Ferno Grills Warranty Information Page | 4... -
Page 5: Introduction
Ferno and your purchase means that these values are important to you as well. Please take a moment to read through this guide outlining the proper care and use of your new Ferno Grill. We are sure that you will enjoy many years of great grilling. -
Page 6: Freestanding Grill Overview And Specifications
Top of Frame Frame Max. Grill w/o Grill Model Open Closed Surface Base Surface Base Outer Tank Primary Warming SA-3BLP-01 63.5" 46" 37" 38" 66" 25" 24" 260 lbs 525 sq. in. 105 sq. in. SA-3BNG-01 63.5" 46" 37" 38"... -
Page 7: Freestanding Grill Application Requirements
FREESTANDING GRILL APPLICATION REQUIREMENTS Because of their mobility, freestanding grills are 3. If the freestanding grill is using Natural Gas more versatile in their applications. They can be (NG), position the grill in the vicinity of a gas moved around to various locations depending on outlet/valve to minimize the amount of convenience and accessibility. -
Page 8: Unpacking And Set-Up (Freestanding Model)
FREESTANDING GRILL UNPACKING AND SET-UP The Ferno Freestanding & Built-in Grills arrives INITIAL SETUP (Disregard side shelf related instructions for Built-in Model applications) almost fully assembled and requires only minor 1. Open the lid and cut all zip ties holding the assembly steps. -
Page 9: Operation Of Your Grill
MUST be installed on all gas flare-ups and for slow cooking. equipment. All local codes require this and Ferno supplies the correct regulator with your grill. GRILLING IN WINDY CONDITIONS... -
Page 10: Pre-Grill Checklist
PRE-GRILL CHECKLIST BEFORE YOUR FIRST USE CHECKLIST BEFORE EACH USE 1. Make sure ALL packing materials have been Always make sure that: removed from the interior of the grill, and that 1. You do NOT smell gas BEFORE you light the ALL zip-ties holding contents in place have been grill. -
Page 11: Lighting Your Grill
LIGHTING YOUR GRILL smell gas, follow the steps listed in the ‘GAS WARNING CONNECTIONS’ section. If the burners still do not light after several attempts, refer to the 1. Never attempt to light the grill if you smell gas. instructions below for manual lighting. 2. -
Page 12: Pre-Heating
On your DO NOT leave the grill unattended during the Ferno Grill, the heat is also regulated by using the pre-heat process or at ANY time while the grill is in Firewheel to set the burner height as well as use. -
Page 13: Using The Firewheel
USING THE FIRE WHEEL The Firewheel on your Ferno Grill is the first of its OPTIONAL SMOKER BOX kind, adding functionality and bringing an entirely The purchase of the optional ‘Smoker Box’ is a new dimension to gas grilling. great addition to the grilling experience, imparting the flavor of wood smoke to your food. - Page 14 OPTIONAL SMOKER BOX continued WOOD CHIPS There are many wood chips available and selection is based on personal taste. The most common are mesquite or hickory. Soak the chips in water for at least 30 minutes before putting them in the box. This will prolong their smoldering time and provide more smoke.
-
Page 15: Cleaning Your Grill
If the grill is NOT covered, the drip pan will collect water and cause overflow and spillage. Do NOT use ANY abrasives on the front panel, as it Ferno Grills is NOT liable for damage caused by will show rub marks. grease overflow. -
Page 16: Cleaning The Burners
CLEANING THE GRATES and clean them with a sponge backed with a Scotch Your Ferno Grill is equipped with cast iron cooking Brite material. grates. These grates should be treated with care and in a similar manner to a cast iron pan. - Page 17 4. Pull out cotter pins from both ends of each TO RE-INSTALL THE BURNERS burner. Remove the RIGHT burner first by 1. Reverse the removing burner instructions as lifting slightly up and to the left and then up listed above in steps 1-4 but note that the left and out.
-
Page 18: Lubricating The Chain And Jack Screw
The chain and jack screws that make it possible for the burners to be raised and lowered inside of your Ferno Grill leave the factory with enough lubrication to last for many years. If at some point the grill begins to squeak when raising or lowering... -
Page 19: Installations & Connections
The small hardware and accessories box included procedure described above. with your Ferno Grill comes with one (1) 9V battery that provides the power for the electronic ignition C CELL BATTERIES system and three (3) C Cell batteries for the 1. -
Page 20: Built-In Installations
VENTILATION REQUIREMENTS (FOR ALL GAS WARNING! TYPES: NATURAL GAS, BULK PROPANE, L.P. CYLINDER) ENCLOSURES BUILT TO HOUSE A FERNO BUILT- IN GRILL MUST BE MANUFACTURED USING At least four (4) ventilation openings, both upper ONLY NON-COMBUSTIBLE MATERIALS. and lower, MUST be provided on both sides of the The grill, enclosure, and propane enclosure if enclosure. - Page 21 REQUIREMENTS WHEN USING AN L.P. CYLINDER TYPICAL NATURAL GAS & BULK L.P. HOOK-UP IN THE ENCLOSURE When using a propane tank, an integral means of limiting the movement of the L.P. gas cylinder is required inside of the enclosure. Lateral movement must not exceed 1 inch when installed in the retention device, and the L.P.
-
Page 22: Gas Connections
GAS CONNECTIONS This grill has been factory pre-set to use either to attach the hose assembly to the grill are Propane Gas (LP) or Natural Gas (NG). It is critical included. that the gas you use matches the gas that the grill BULK TANK LP has been set up for. - Page 23 4. Always leak test the connection after refilling or use any assembly other than the one supplied exchanging LP gas cylinders. See ‘Leak Test with your Ferno Grill. Procedure’ in section entitled ‘Final Checks’ Do NOT attempt to use a 5LP-A equipped...
- Page 24 Ferno safety feature when the coupler is Grills for connection with a cylinder connecting disconnected.
-
Page 25: Natural Gas (Ng)
1. To ensure satisfactory performance, the gas (FREESTANDING MODEL) supply line must be sized to accommodate the 1. To connect your Ferno Grill to Natural Gas, TOTAL BTU requirements of all the gas fired insert the natural gas hose through the equipment that will be connected to this line. -
Page 26: Final Checks
FINAL CHECKS LEAK TEST PROCEDURE Locations to Leak Check – Natural Gas Setup 1. Create a soapy solution of 1 part dish soap and (Freestanding Model) 3 parts water. 2. Confirm that all valve control knobs are in the ‘OFF’ position. 3. - Page 27 LOW HEAT BURNER ADJUSTMENT Flames should be blue in color and stable, with a slight yellow tip. The bright blue core should be The burners on your grill feature an adjustable around 3/8” tall with a total flame height of around ‘LOW’...
-
Page 28: Troubleshooting Guide
See 2. Replace the LED – this component is not a user ‘Cleaning the Burners’ in the section entitled serviceable part so please contact Ferno Grills ‘CLEANING YOUR GRILL’ for further details. Customer Care at 888-800-1688. - Page 29 SMELL OF GAS WHILE COOKING and appear to ‘lift’ off the burner, then repeat the process and modify your shutter WARNING! adjustment until the flames are blue, stable, and quiet. IF YOU SMELL GAS WHILE THE GRILL IS OPERATING, IMMEDIATELY TURN OFF ALL BURNERS AND SHUT OFF THE MAIN FUEL SUPPLY.
- Page 30 tank. The regulator contains a flexible 1. Make sure that the supply line is at least 3/4” diaphragm and should not be allowed to touch ID (inside diameter) or 1” OD (outside the grill body or its surroundings. diameter). 8. Ensure that the burners and drip tray are clean 2.
-
Page 31: Troubleshooting Quick Reference Guide
In most cases, these troubleshooting tips can be performed by the grill owner. Please read and follow the steps carefully. If you have exhausted the troubleshooting steps, OR if you are not comfortable working on your grill, please contact the Ferno Customer Care Team: Tel: 888-800-1688 Email: info@fernogrills.com PROBLEM... -
Page 32: Grill Wiring Diagram
GRILL WIRING DIAGRAMS Ignition Wiring Handle Wiring Page | 32... -
Page 33: Freestanding Model Exploded View Parts Lists
EXPLODED VIEW AND REPLACEMENT PARTS LIST (FREESTANDING MODEL) Page | 33... - Page 34 FG Part Item Description Quantity Number THERMOMETER THERMOMETER BEZEL THERMOMETER BEZEL GASKET THERMOMETER NUT HANDLE ASSEMBLY (KEY) KA-1 LED Driver PCB O-RING, BATTERY END CAP HANDLE END CAP BATTERY CARTRIDGE ASSEMBLY LED LIGHT 2-56 x .188, Phillips Pan Head, Stainless Steel HANDLE GASKET O-RING (-217, SILICONE) GLASS DISC...
- Page 35 SKIN, REAR ASSEMBLY BURNER BED FRAME ELECTRODE COVER ORIFICE HOLDER ORIFICE, #59 ORIFICE, #52 Screw, 8-32 x .312, Phillips Pan, External Tooth Lock Washer, Stainless Steel ORIFICE BRACKET GAS DISTRIBUTION LINE, 9IN GAS DISTRIBUTION LINE, 8IN GAS VALVE ASSEMBLY (KEY) KA-2 POINTER, GAS KNOBS Screw, 6-32 x .250, Phillips Pan, External Tooth Lock Washer,18-8 SS...
- Page 36 Bolt, M10 x 1.5 x 20, Hex Head, SS 18-8 GROMMET, TANK BASE TANK BASE HOSE, LP GAS REGULATOR FITTING, .500FEMALE FLARE TO .375 FLARE REGULATOR, NG Screw, 8-32 x .375, Phillips Pan, External Tooth Lock Washer, Stainless Steel BRACKET, NG REGULATOR Screw, Self-Tapping, 8-32 x .312, Flanged Hex, Stainless Steel HOSE, NG REGULATOR TO GRILL Brass Fitting, .5 NPT to .5 45deg Flare...
-
Page 37: Built-In Model Exploded View Parts Lists
EXPLODED VIEW AND REPLACEMENT PARTS LIST (BUILT-IN MODEL) Page | 37... - Page 38 HANDLE GASKET O-RING, BATTERY END CAP LED Driver PCB BATTERY CARTRIDGE LED LIGHT GAS KNOB WITH INSERT HINGE PIN, LID TOP PLATE WHEEL ASSEMBLY HINGE STOP BAR, LEFT THERMOMETER BEZEL GASKET POINTER, GAS KNOBS 12-24 x 3/8, PHILLIPS PAN HEAD, STAINLESS STEEL Washer, #12, External Tooth Lock, Stainless Steel HANDLE END CAP 2-56 x .188, Phillips Pan, 18-8 SS...
- Page 39 BURNER, LEFT BURNER, CENTER BURNER, RIGHT UPPER RADIENT ELECTRODE COVER IGNITER HOLDER WELDMENT 1 IGNITER HOLDER WELDMENT 2 HEAT SHIELD ASSEMBLY, LEFT HEAT SHIELD ASSEMBLY, RIGHT TENSIONER ARM SPRING, TENSIONER, RIGHT SPRING, TENSIONER, LEFT Washer, #10 x .625 x .06, Stainless Steel BUSHING, TOP IDLER Screw, .250-20 x .500, Hex Head, Stainless Steel Bolt, .375-24 x .750, Hex Head, Stainless Steel...
- Page 40 GRATE HOOK COVER, BUILT IN SMOKER BOX 300/301 HANDLE GASKET Page | 40...
-
Page 41: Ratings Plate/Serial Number Information
FERNO GRILLS RATINGS/SERIAL NUMBER INFORMATION (For the Freestanding Model, located on the outside and inside rear of the tank shroud, for the Built-in Model, located on the bottom of the Drip Tray and on the lower left side of the grill body.) -
Page 42: Ferno Grills Warranty Information
This warranty gives you specific legal rights and you may have other rights, which vary from state to state. No one has the authority to add to or vary Ferno Grill’s warranty, or to create for Ferno Grills any other obligation or liability in connection with the sale or use of its products and is limited to the replacement of defective parts with the owner paying all other costs including labor.