Download Table of Contents Print this page
Husqvarna AUTOMOWER 310 Operator's Manual

Husqvarna AUTOMOWER 310 Operator's Manual

Hide thumbs Also See for AUTOMOWER 310:


Quick Links

Operator's manual
EN, English
Read the operator's manual carefully and make sure that you understand the instructions before
you use the product.


Table of Contents

Summary of Contents for Husqvarna AUTOMOWER 310

  • Page 1 Operator's manual ® HUSQVARNA AUTOMOWER 310/315/315X EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
  • Page 2: Table Of Contents

    Contents 5 Maintenance 5.1 Introduction - maintenance........46 1 Introduction 5.2 Clean the robotic lawnmower.......46 1.1 Introduction............3 5.3 Replace the blades..........46 1.2 Support..............3 5.4 Battery..............47 1.3 Product description..........3 5.5 Winter service............47 1.4 Finding the charging station........3 1.5 Product overview ...........4 6 Troubleshooting 1.6 Symbols on the product.........
  • Page 3: Introduction

    The serial number is on the product rating plate and on the product registration key. • Use the product registration key and the serial number to register your product on 1.2 Support For support about the Husqvarna product, speak to your servicing dealer.
  • Page 4: Product Overview

    This search method is suitable in an installation with an open lawn space, wide passages (wider than about 3 m /10 ft.), and no or only a few small islands. The benefit of this search method is that there is no need to install a guide wire.
  • Page 5: Symbols On The Product

    20. Skid plate Noise emission to surroundings. The 21. Power supply (the appearance of the power supply product’s emissions are set out in may differ depending on market) Technical data on page 57 and on the 22. Loop wire for boundary loop and guide wire rating plate.
  • Page 6: Safety

    2 Safety 2.1 Safety definitions 2.2 General safety instructions Warnings, cautions and notes are used to point out The following system is used in the Operator’s Manual specially important parts of the manual. to make it easier to use: italics is a text that is shown on the •...
  • Page 7 Please read the Operator’s Manual • Husqvarna does not guarantee full compatibility carefully and make sure you understand the between the robotic lawnmower and other types of instructions before using the robotic lawnmower.
  • Page 8 2.3.4 In the event of a thunderstorm 3. Carry the robotic lawnmower by the handle under the robotic lawnmower with the blade disc away from the body. To reduce the risk of damage to electrical components in the robotic lawnmower and its charging station, we recommend that all connections to the charging station are disconnected (power supply, boundary wire and guide wires) if there is a risk of a thunderstorm.
  • Page 9: Installation

    Draw on the sketch where the boundary and guide wires should be routed. Visit for further descriptions and tips regarding installation. 1. If the lawn in the working area is longer than 10 cm / 4 in.
  • Page 10: Charging Station

    • Power supply • Low voltage cable • Screws for the charging station 3 m / 10 ft • Measurement gauge 3.2.1 Installation tools During installation you will also need: • Hammer/plastic mallet (to simplify putting the pegs 2 m / 7 ft in the ground).
  • Page 11 The charging station should not be placed on an island as this limits the laying of the guide wire in an optimal It is possible to let the low voltage cable cross the way. However, if the charging station has to be installed working area if it is stapled down or buried.
  • Page 12: Charging The Battery

    WARNING: No parts of the power supply must under any circumstances be changed or tampered with. The low voltage cable must not be shortened or extended. WARNING: Use the plug to disconnect the charging station, for instance before cleaning the charging station or repairing the loop wire. CAUTION: It is not permitted to make new holes CAUTION: Place the low voltage cable and in the charging station’s plate.
  • Page 13 • Bury the wire. 3.5.2 Working area boundaries Depending on what the working area is adjacent to, the Bury the boundary wire if you want to dethatch or boundary wire must be laid at different distances from aerate the lawn. If necessary, both methods can be obstacles.
  • Page 14 When the working area is divided by a paving stone path that is level with the lawn, it is possible to allow the robotic lawnmower to run over the path. It can be an advantage to lay the boundary wire under the paving stones.
  • Page 15 60 cm / 24 in (between boundary wires). Note: In passages narrower than 2 m / 6.5 ft. (between boundary wires) Husqvarna recommends that a guide wire is installed. Slopes The robotic lawnmower can operate in slopes. The...
  • Page 16 If the boundary wire is to be buried: • Make sure to lay the boundary wire at a minimum of 1 cm / 0.4 in. and a maximum of 20 cm / 8 in. in the ground. The wire can be buried for instance using an edge cutter or a straight spade.
  • Page 17: Connecting The Boundary Wire

    2. Press the connectors together using a pair of pliers. Press until you hear a click. Splicing the boundary wire CAUTION: Twinned cables, or a screw terminal block that is insulated with insulation tape are not satisfactory splices. Soil moisture will cause the wire to oxidise and after a time result in a 3.
  • Page 18 the connection from the guide wire to the boundary loop. 2. Tilt the top cover on the charging station forward and run the guide wire through one of two channels marked GUIDE leading to the guide connection. 3. Fit a connector to the guide wire in the same way as Connecting the boundary for the boundary wire in wire on page 17 .
  • Page 19: Checking The Installation

    3.8 Checking the installation easier if an eyelet has been made on the boundary wire as outlined in the previous description. See Check the loop signal by inspecting the indicator lamp Laying the boundary wire on page 16 . on the charging station. Indicator lamp in the charging station on page 52 if the lamp does not indicate a solid or flashing green light.
  • Page 20: Automower ® Connect Menu

    Note: The product is available for pairing for 3 minutes. If pairing has not been successful within this time period, turn off the product (Main switch, position 0). Wait until the LED indicator lamp goes out, and then set the Main switch to position 1 again. 4.
  • Page 21: Connectivity

    Connect app, ® Pairing with the Automower Connect app on refer to Husqvarna cannot guarantee the uptime or coverage of page 19 . the 3rd party data connection (long-range connectivity). However, it is always possible to communicate with the 3.12 Connectivity product via Bluetooth, as long as you are within short- ®...
  • Page 22: Test Docking With The Charging Station

    ™ about Husqvarna Fleet Services and how to subscribe also to make selections in certain setting options. to the services on • The MENU button is used to go to the main menu. • The PARK button is used to send the robotic lawnmower to the charging station.
  • Page 23: Menu Structure

    no GPRS reception.The SIM symbol (K) indicates there is a problem with the SIM card or the SIM module. Make sure the SIM card support local data communication, and that there is sufficient funds on the card (applies to pre-paid SIM cards). Also make sure that APN settings agree.
  • Page 24: Timer

    The factory timer setting is inactive, which means that Automower Connect. Contact your local the robotic lawnmower will operate around the clock 7 Husqvarna representative for information days a week. This is normally a suitable setting for a on what accessories are available for your...
  • Page 25: Security

    ® 3.16.2 Timer suggestions Automower Work area Work days per week Work hours per day Suggestion of time interval 250 m 07:00 - 12:30 07:00 - 11:00 500 m 10.5 07:00 - 17:30 07:00 - 14:30 750 m 15.5 07:00 - 22:30 07:00 - 18:00 1000 m 03:00 - 24:00...
  • Page 26: Messages

    Low and Medium security prohibits access to the robotic Change PIN code High security lawnmower if the PIN code is unknown. 1. Enter the current PIN code by using the up/down also includes a warning that beeps if the correct PIN arrow keys and press OK.
  • Page 27: Weather Timer

    3.18.2 Info messages Messages shown in the display not caused by an actual Cutting time Info messages fault are instead saved under the Slope too Medium heading. Examples for such messages is steep . See Information messages on page 51 for more High information on possible reasons for each message.
  • Page 28 Area 1, 2 or 3 > How far? Enter the distance in metres along the current wire from the charging station to the remote area where the robotic lawnmower begins mowing. Area2 Use the right and left arrow keys to alternate between the different options.
  • Page 29 Area 1, 2 or 3 > More > Reset using the left right select arrow keys followed by OK. 3.20.3 Find charging station The robotic lawnmower can be set to search for the charging station in one or more of the following three ways: Guide, Boundary loop and Charging station.
  • Page 30 Guide along the boundary wire and instead start to follow the guide wire into the charging station. Use the number keys to enter the delay time. The delay time is normally specified as a figure between 0 and 10 minutes. Boundary loop >...
  • Page 31 or wall which prevents the robotic lawnmower from docking with the charging station despite making contact with the charging station’s signals. In these cases, it is normally better to move the charging station, but if this is not possible, the range of the charging station can be reduced.
  • Page 32: Settings Corridor width > Guide The guide corridor width is adjusted automatically. Only in rare occasions manual settings need to be entered. 0 and 9 . The guide corridor width can be set between 0 , the robotic lawnmower If guide corridor width is set to will straddle the guide wire.
  • Page 33 4. Save a profile for the new charging station. To use the robotic lawnmower in the original charging Use Profiles station, the first profile must now be selected. To use the robotic lawnmower in the new charging station, that Profile A, B or C Select profile must be selected.
  • Page 34: Accessories

    Mower house Time format Date format 3.22.1 Information This menu handles accessories mounted on the mower. Contact Husqvarna customer service for more Set time: Enter the correct time and press OK to • information on available accessories. exit. Set date: Enter correct date and press OK to exit.
  • Page 35 3.22.2 Information My mowers My mowers you can manage all the When choosing ® ® Only applicable to Automower 310 and Automower robotic lawnmowers coupled to your account as well as 315. add new ones. ® The Automower Connect app provides two modes of Pairing connectivity: Long-range cellular connectivity and Short- ®...
  • Page 36 SIM PIN Avoid collisions with mower house This menu is only applicable if you use a non-Husqvarna If this option is selected, the wear on the mower and the SIM. house is reduced, but it can result in more uncut grass APN settings around the charging station.
  • Page 37: Menu Structure Overview

    3.23 Menu structure overview Timer Overview/Monday Period 1 Period 2 Copy Reset Current All week days Security Advanced Security level New loop Change Duration Medium High signal PIN code Duration Duration of alarm of time lock Messages Fault Info messages messages Weather timer * Use weather timer...
  • Page 38: Menu Structure Overview

    3.24 Menu structure overview Installation Lawn Find charging station Advanced coverage Guide Boundary Charger GPS Auto*** Charging Area 1-3 station range Delay Delay Disable More Disable More time time Test Reset Test Test Reset guide right left How? Disable More Corridor Exit Reversing...
  • Page 39: Yard Layout Examples

    The recommended timer settings in the following examples are applicable to Automower 310/315/315X unless otherwise stated. There is more installation help on Note: The default settings for the robotic lawnmower have been chosen to work in as many different gardens as possible.
  • Page 40 3.25.3 L-shaped garden with a couple of islands and the charging station installed in the narrow area Area 800 m Timer ® Automower 07:00 - 24:00, Monday to Sunday ® Automower 315/315X 08:00 - 22:00, Monday to Sunday Lawn coverage Area 1: How? Guide How far? X m...
  • Page 41 3.25.5 Unsymmetrical working area with a narrow passage and a number of islands Area 800 m Timer ® Automower 07:00 - 24:00, Monday to Saturday ® Automower 315/315X 08:00 - 22:00, Monday to Saturday 2 m / 7 ft Lawn coverage Factory setting Find charging sta- Factory setting...
  • Page 42 3.25.7 A secondary area Area 500 + 100 m Timer ® Automower 310: 08:00 - 20:30, Monday, Tuesday, Thursday, Friday, Saturday ® Automower 315/315X: 08:00 - 18:30, Monday, Tuesday, Thursday, Friday, Saturday Lawn coverage Factory setting Find charging sta- Factory setting tion Remarks The secondary area is cut using the...
  • Page 43: Operation

    4 Operation 4.1 Main switch Note: Always press the START button before closing the hatch to start the robotic lawnmower. If the START WARNING: Read the safety instructions button is not pressed, a message beep is heard and the carefully before you start your robotic robotic lawnmower will not start.
  • Page 44: Operating Mode Park

    On Main pressing right arrow key and then specifying WARNING: Always switch off the robotic area or On Secondary area . lawnmower using the main switch if it requires maintenance, or if the robotic lawnmower must 4.4 Operating mode Park be moved outside the working area.
  • Page 45: Charge A Flat Battery

    Operation, A + C = max. hours Charging/Standby, B + D = min. hours 4.8 Charge a flat battery When the Husqvarna robotic lawnmower is new or has been stored for a long period, the battery will be flat and needs to be charged before starting.
  • Page 46: Maintenance

    It is recommended to clean twigs and other objects that may impede docking. using a brush. 5.3 Replace the blades Husqvarna offers a special cleaning and maintenance kit as an accessory. Please, contact Husqvarna customer WARNING: Always use blades and screws of service.
  • Page 47: Battery

    Contact your local Husqvarna representative to replace the battery. 5.5 Winter service Take your robotic lawnmower to your local Husqvarna representative for service prior to winter storage. Regular winter service will maintain the robotic lawnmower in good condition and create the best conditions for a new season without any disruptions.
  • Page 48: Troubleshooting

    6.2 Fault messages Below a number of fault messages are listed which may be shown in the display of the robotic lawnmower. Contact your local Husqvarna representative if the same message appears often. Message Cause...
  • Page 49 Wrong PIN code Wrong PIN code has been entered. Five at- Enter the correct PIN code. Contact your lo- tempts are permitted, and the keypad is then cal Husqvarna representative if you forget the blocked for five minutes. PIN code. No drive...
  • Page 50 Message Cause Action Stuck in charging sta- There is an object in the way of the robotic Remove the object. tion lawnmower preventing it from leaving the charging station. Upside down The robotic lawnmower is leaning too much Turn the robotic lawnmower the right way up. or has turned over.
  • Page 51: Information Messages

    6.3 Information messages Below a number of information messages are listed which may be shown in the display of the robotic lawnmower. Contact your local Husqvarna representative if the same message appears often. Message Cause Action...
  • Page 52: Indicator Lamp In The Charging Station

    If your robotic lawnmower does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on which provides more detailed answers to a number of standard questions. Contact your local Husqvarna representative if you still cannot find the reason for the fault.
  • Page 53: Find Breaks In The Loop Wire

    Symptoms Cause Action The robotic lawnmow- The robotic lawnmower searches for the No action. The blade disc does not rotate er runs, but the blade charging station. when the robotic lawnmower is searching for disc does not rotate. the charging station. Clean The robotic lawnmow- Grass or other foreign object blocks the blade...
  • Page 54 a) If the suspected boundary wire is short then it is easiest to exchange all of the boundary wire between AL and the point where the guide wire is connected to the boundary wire (thick black line). b) If the suspected boundary wire is long (thick black line) then do as follows: Put AL and G1 back to their original positions.
  • Page 55 Continue until only a very short section of the wire remains which is the difference between a solid green light and a flashing blue light. Then follow instruction in step 5 below. 4. If indicator lamp still flashes blue in step 3 above: Put AL and G1 back in their original positions.
  • Page 56: Transportation, Storage And Disposal

    Keep the product in a dry, frost free space. • Keep the product with all wheels on level ground during storage, or use a Husqvarna wall hanger. • If you keep the charging station indoors, disconnect and remove the power supply and all the connectors from the charging station.
  • Page 57: Technical Data

    8 Technical data 8.1 Technical data ® ® ® Dimensions Automower Automower Automower 315X Length, cm Width, cm Height, cm Weight, kg 10.1 ® ® ® Electrical system Automower Automower Automower 315X Battery, Lithium-Ion 18 V/2.1 Ah 584 85 28-01, 584 85 584 85 28-01, 584 85 584 85 28-01, 584 85 Art.No...
  • Page 58 Power Class 1 (for DCS/ 30 dBm PCS) Husqvarna AB does not guarantee full compatibility between the robotic lawnmower and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar. 58 - Technical data...
  • Page 59: Warranty

    The blades and wheels are seen as disposable and are not covered by the guarantee. If an error occurs with your Husqvarna robotic lawnmower, please contact Husqvarna customer service for further instructions. Please have the receipt and the robotic lawnmower’s serial number at hand when...
  • Page 60: Ec Declaration Of Conformity

    10 EC Declaration of Conformity 10.1 EC Declaration of Conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares that the Robotic lawnmovers ® Husqvarna Automower 310 and Husqvarna ® Automower 315 with serial numbers dating 2017 week 45 and onwards (the year and week is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
  • Page 61 840 - 001 - EC Declaration of Conformity - 61...
  • Page 62 62 - EC Declaration of Conformity 840 - 001 -...
  • Page 63 840 - 001 - EC Declaration of Conformity - 63...
  • Page 64 AUTOMOWER ® is a trademark owned by Husqvarna AB. © Copyright 2018 HUSQVARNA. All rights reserved. Original instructions 1140542-26 2018-06-29...

This manual is also suitable for:

Automower 315Automower 315x

Table of Contents