Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Emax Nanohawk 1S BNF FrSky
Summary of Contents for Emax Nanohawk 1S BNF FrSky
- Page 1 Thanks for purchasing the Nanohawk. Designed in California, assembled in China.
-
Page 2: Precautions
Please fly in a safe area away from people Do not modify or use other parts and accessories not approved for the use of EMAX. Do not use this product in harsh environments (such as winds, rain, lightning, snow, etc.). -
Page 3: Table Of Contents
Changing VTX setting via Betaflight OSD .............. 6 Emax On-Board Receiver ..................7 Binding Procedure ....................7 Emax Nanohawk Flight Controller (FC) ..............8 Stock Flight Controller Settings ................8 Adjusting Software Settings (Betaflight Configurator) ......... 8 Reprogramming Nanohawk Flight Controller ............8 Restoring the Tinyhawk default settings ............. -
Page 4: Disclaimer
1 Cell 300 mAh HV lipo battery Product list 1. Nanohawk × 1 2. Instruction manua cardl × 1 3. Emax 1s HV 300 mAh × 1 4. Charger × 1 5. Extra Propeller Set (2x CW, 2x CCW) 6. Screwdriver x 1 7. -
Page 5: Nanohawk Structure
1. Line up the 3 struts of the propeller with the 3 struts on the motor bell. 2. Press on the propeller while supporting the backside of the motor with our fingers. 3. Press on until the motor shaft is flush with the propeller. emax-usa.com... -
Page 6: Propeller Dismount
Caution: Failure to support the motor sufficiently can cause the frame to break. Use caution when pressing the propellers off. Nanohawk VTX Settings NOTE: You must “disable” VTX Smart AUDIO on UART 2 in order for push button VTX adjustment to work as described below. Vtx Schematic and Button Diagram emax-usa.com... -
Page 7: Vtx Channel Settings With The Button
Notice: If you change to an illegal channel using SmartAudio, there will be no image transmitting from Nanohawk. To switch back to a legal channel, press the button on the vtx and follow the vtx menu guide shown below. emax-usa.com... - Page 8 EU/CE: Do not use Use Unlocked Configuration. * By purchasing this product, the user is agreeing that he/she understands these responsibilities and will operate the equipment legally. EMAX cannot be held responsible for a user’s actions purchasing and/or using this product in violation of the governmental regulations.
-
Page 9: Changing Vtx Setting Via Betaflight Osd
While pulling ROLL stick left and right to change the corresponding parameters.Once the parameters is set, moving the cursor to “SET”, then turn ROLL stick right to enter “SET” and choose “YES” and turn ROLL stick right to save setting parameters, as shown in Figure 5. Figure 5 emax-usa.com... -
Page 10: Emax On-Board Receiver
Nanohawk’s main electronic board is shown above. This board contains a F4 flight controller with all 4 esc’s and an 8CH receiver. Emax On-Board Receiver The receiver is integrated into the main flight controller board and is set up via betaflight. -
Page 11: Emax Nanohawk Flight Controller (Fc)
300 mAh battery for ultimate control of flight indoors and outdoors. Please do not change these values. Rate Profiles: Profile 1 is designed for optimal indoor flight control with the Emax 1s HV 300 mAh Battery. Adjusting Software Settings (Betaflight Configurator) Betaflight Configurator can be used to changed programmed settings on Nanohawk and to flash new firmware if desired. -
Page 12: Restoring The Tinyhawk Default Settings
4. Select Flash Firmware to program the flight controller Restoring the Tinyhawk default settings 1. Download the latest CLI Dump File from https://emax-usa.com/ 2. Connect Nanohawk to Betaflight configurator and select the CLI tab 3. Open the CLI Dump File in a text editor and copy all the text. -
Page 13: Flight
Calibration takes a few seconds then Nanohawk is ready to fly. Nanohawk can fly for 4 minutes on a fully charged battery. Land Nanohawk when the battery reaches 3.2v; flying any longer can severely damage your battery and is not recommended. emax-usa.com... -
Page 14: Arming
Nanohawk. The OSD displays important information such as flight time and battery voltage. Pay attention to these numbers during flight to know how much battery life is left. Nanohawk can fly for a maximum of 4 minutes. When the battery reaches 3.2v, emax-usa.com... - Page 15 2 position (middle); this is useful when looking for Nanohawk. Thank you for purchasing our product! Enjoy Flying Nanohawk Warning： Please pay attention to your surroundings. Not recommended for persons under 18 years of age. emax-usa.com...