H3C MSR 20 Series Manual
  1. Manuals
  2. Brands
  3. H3C Manuals
  4. Network Router
  5. MSR 20 Series
  6. Manual
H3C MSR 20 Series Manual

H3C MSR 20 Series Manual

Interface card and interface module
Hide thumbs Also See for MSR 20 Series:
Table of Contents

Advertisement

Quick Links

H3C MSR 20/30/50 Series Routers
Interface Card and Interface Module Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08237K-20070726-C-1.02

Advertisement

Table of Contents
loading

Related Manuals for H3C MSR 20 Series

Summary of Contents for H3C MSR 20 Series

  • Page 1 H3C MSR 20/30/50 Series Routers Interface Card and Interface Module Manual Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-08237K-20070726-C-1.02...
  • Page 2 Copyright © 2006-2007, Hangzhou H3C Technologies Co., Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.
  • Page 3 About This Manual Related Documentation In addition to this manual, each H3C MSR 20/30/50 Series Routers documentation set includes the following: Manual Description Provides information about H3C MSR 20 Router in H3C MSR 20 Series Routers terms of hardware features, installation, Installation Manual configuration, maintenance, and troubleshooting.
  • Page 4 LEDs, and installation of ESMs/VCPMs. Appendix Interface Shows you the SICs, MIMs, and FICs that can work Card Interface with H3C MSR 20/30/50 Series Routers. Module Purchase Guide Conventions The manual uses the following conventions: I. Symbols Convention Description Means reader be extremely careful.

  • Page 5: Table Of Contents

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents Table of Contents Chapter 1 Overview ........................1-1 1.1 SIC/DSIC Interface Cards....................1-1 1.2 MIM/DMIM/XMIM ....................... 1-2 1.3 FIC/DFIC Interface Cards ....................1-4 1.4 SIC/MIM/FIC Purchase Guideline..................1-7 1.5 Installation/Removal of a SIC/MIM/FIC ................
  • Page 6 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 2.5.1 Introduction......................2-18 2.5.2 Interface Attributes ....................2-18 2.5.3 Interface LEDs....................... 2-18 2.5.4 Interface Cable ...................... 2-19 2.5.5 Connecting the Interface Cable................2-19 2.6 SIC-1FXS/SIC-1FXO & SIC-2FXS/SIC-2FXO..............2-20 2.6.1 Introduction......................
  • Page 7 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 2.12 SIC-1ADSL-I ........................2-41 2.12.1 Introduction......................2-41 2.12.2 Interface Attributes ....................2-41 2.12.3 Interface LEDs..................... 2-42 2.12.4 Interface Cable ....................2-42 2.12.5 Connecting the Interface Cable................2-43 2.13 SIC-1BS/SIC-2BS&SIC-1BU/SIC-2BU ................
  • Page 8 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 3.2.5 Connecting the Interface Cable................3-5 3.3 MIM-1GEF/MIM-2GEF Module..................3-6 3.3.1 Introduction......................3-6 3.3.2 Interface Attributes ....................3-6 3.3.3 Interface LEDs......................3-7 3.3.4 Interface Cable ......................3-8 3.3.5 Connecting the Interface Optic Fiber ..............
  • Page 9 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 3.9.4 Interface Cable ...................... 3-37 3.9.5 Connecting the Interface Cable................3-37 3.10 MIM-1CE3 Module......................3-38 3.10.1 Introduction......................3-38 3.10.2 Interface Attributes ....................3-38 3.10.3 Interface LEDs..................... 3-39 3.10.4 Interface Cable ....................
  • Page 10 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 3.16.5 Connecting the Interface Cable................3-55 3.17 MIM-1POS Module ......................3-55 3.17.1 Introduction......................3-55 3.17.2 Interface Attributes ....................3-55 3.17.3 Interface LEDs..................... 3-56 3.17.4 Interface Cable ....................3-56 3.17.5 Connecting the Interface Cable................
  • Page 11 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 3.24 MIM-16FSW/MIM-16FSW-PoE/DMIM-24FSW/DMIM-24FSW-PoE ......3-77 3.24.1 Introduction......................3-77 3.24.2 Interface Attributes ....................3-77 3.24.3 Interface LEDs..................... 3-78 3.24.4 Interface Cable ....................3-80 3.24.5 Connecting the Interface Optic Fiber ..............3-81 3.25 MIM-IMA-4E1/MIM-IMA-8E1 Module................
  • Page 12 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents Chapter 4 Flexible Interface Cards ....................4-1 4.1 FIC-1FE/FIC-2FE/FIC-4FE ....................4-1 4.1.1 Introduction......................4-1 4.1.2 Interface Attributes ....................4-1 4.1.3 Interface LEDs......................4-2 4.1.4 Interface Cable ......................4-3 4.1.5 Connecting the Interface Cable................
  • Page 13 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 4.7.4 Interface Cable ...................... 4-30 4.7.5 Connecting the Interface Cable................4-31 4.8 FIC-1T1/FIC-2T1/FIC-4T1 and FIC-1T1-F/FIC-2T1-F/FIC-4T1-F ........4-32 4.8.1 Introduction......................4-32 4.8.2 Interface Attributes ....................4-32 4.8.3 Interface LEDs....................... 4-33 4.8.4 Interface Cable ......................
  • Page 14 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 4.14.4 Interface Cable ....................4-51 4.14.5 Connecting the Interface Cable................4-51 4.15 FIC-1ATM-OC3MM/FIC-1ATM-OC3SM/ FIC-1ATM-OC3SML ........4-52 4.15.1 Introduction......................4-52 4.15.2 Interface Attributes ....................4-52 4.15.3 Interface LEDs..................... 4-53 4.15.4 Interface Optical Fiber..................
  • Page 15 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 4.22 FIC-1VE1 ........................4-72 4.22.1 Introduction......................4-72 4.22.2 Interface Attributes ....................4-72 4.22.3 Interface LEDs..................... 4-72 4.22.4 Interface Cable ....................4-73 4.22.5 Connecting the Interface Cable................4-74 4.23 FIC-1VT1 ........................
  • Page 16 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Table of Contents 4.29 FIC-2BSV/FIC-4BSV Module..................4-93 4.29.1 Introduction......................4-93 4.29.2 Interface Attributes ....................4-94 4.29.3 Interface LEDs..................... 4-94 4.29.4 Interface Cable ....................4-95 4.29.5 Connecting the Interface Cable................4-96 4.30 FIC-24FXS ........................

  • Page 17: Chapter 1 Overview

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview Chapter 1 Overview This manual covers three broad categories of interface cards and modules available with MSR Series Routers: smart interface card/double smart interface card (SIC/DSIC),...

  • Page 18: Mim/Dmim/Xmim

    1-port ISDN BRI S/T voice interface card (SIC-1BSV) 2-port ISDN BRI S/T voice interface card (SIC-2BSV) 1.2 MIM/DMIM/XMIM H3C MSR 30 series routers provide MIM slots and support the following MIM/DMIM/XMIM: I. Ethernet module 1-port 10Base-T/100Base-TX Fast Ethernet interface module (MIM-1FE)
  • Page 19 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview II. WAN module 2-port enhanced high-speed synchronous/asynchronous serial interface module (MIM-2SAE) 4-port enhanced high-speed synchronous/asynchronous serial interface module (MIM-4SAE) 8-port enhanced high-speed synchronous/asynchronous serial interface module...

  • Page 20: Fic/Dfic Interface Cards

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview 8-port E1 ATM inverse multiplexing interface module (MIM-IMA-8E1) 4-port E1 ATM inverse multiplexing interface module (MIM-IMA-4E1) 8-port T1 ATM inverse multiplexing interface module (MIM-IMA-8T1) 4-port T1 ATM inverse multiplexing interface module (MIM-IMA-4T1)
  • Page 21 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview 1-port 1000Base-SX/1000Base-LX GE fiber interface card (FIC-1GEF) 2-port 1000Base-SX/1000Base-LX GE fiber interface card (FIC-2GEF) 16-port 10/100 Mbps Layer 2 switching interface card (FIC-16FSW) 24-port 10/100 Mbps Layer 2 switching interface card (DFIC-24FSW)
  • Page 22 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview 1-port channelized E3 interface card (FIC-1CE3) 1-port ATM 155 Mbps multi-mode fiber interface card (FIC-1ATM-OC3MM) 1-port ATM 155 Mbps single-mode fiber interface card (FIC-1ATM-OC3SM) 1-port ATM 155 Mbps single-mode long-haul fiber interface card (FIC-1ATM-OC3SML)

  • Page 23: Sic/Mim/Fic Purchase Guideline

    Chapter 1 Overview Data encryption card 1.4 SIC/MIM/FIC Purchase Guideline You may equip an H3C series router with appropriate interface cards or modules and are allowed to: Install multiple interface cards or modules of the same type on the router;...

  • Page 24: Installing/Removing A Sic

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview Caution: When replacing/installing an interface card or module, note the following: Do not damage the EMI gaskets on the card/module panel. They can filter electromagnetic interference of the router.

  • Page 25: Installing/Removing A Mim

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview Step 5: Fasten the SIC into the Router with captive screws; Step 6: Power on the Router, and check the LEDs of the corresponding slot on the front panel: after the initialization of the SIC, ON means that the SIC is operating normally and OFF means that its Power-On Self-Test (POST) has failed.
  • Page 26 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview Step 5: Power on the Router, and check the LEDs of the corresponding slot on the front panel: ON means that the MIM is operating normally and OFF means that the POST of the MIM has failed.

  • Page 27: Installing/Removing A Fic

    Step 3: Fix the FIC in the chassis by fastening the captive screws. Repeat these steps to install all the other FICs. 1.6 Troubleshooting H3C Series Routers provide LEDs, thus facilitating you to make sure whether a SIC/MIM/FIC is properly installed by viewing their state as follows: 1-11...
  • Page 28 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 1 Overview After the installation of a SIC/MIM/FIC, turn on the power and view the corresponding LEDs on the cover of the Router chassis: ON means that the SIC/MIM/FIC is operating normally and OFF means that the Power-On Self-Test (POST) of the SIC/MIM/FIC has failed.

  • Page 29: Chapter 2 Smart Interface Cards

    PoE router. Note: For H3C MSR 20-40 and MSR 30 and 50 series routers which have four SIC slots, a 4FSW/1FEF/1FEA/1GEC/1ADSL/1ADSL-I interface card can only be installed in slot 2 or slot 4.

  • Page 30: Interface Attributes

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.1.2 Interface Attributes The interface attributes of SIC-1FEA are given in the following table: Table 2-1 Interface attributes of SIC-1FEA Attribute SIC-1FEA Connector type...

  • Page 31: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.1.4 Interface Cable Normally, category-5 twisted pair cable is adopted to connect the 10BASE-T /100BASE-TX Ethernet interface to the Ethernet, as shown in the following figure:...

  • Page 32: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-3 Interface attributes of the SIC-1SAE Description Attribute Synchronous Asynchronous Connector DB-28 Number connectors V.35, RS449, V.24 Interface standard X.21, RS530 RS232 and operating mode...

  • Page 33: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Description of the LEDs on SIC-1SAE panel is given in the following table: Table 2-4 LEDs on SIC-1SAE panel Description OFF means no link is present;...
  • Page 34 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-5 V.24 DCE cable V.35 DTE cable Figure 2-6 V.35 DTE cable V.35 DCE cable Figure 2-7 V.35 DCE cable X.21 DTE cable Figure 2-8 X.21 DTE cable...
  • Page 35 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-9 X.21 DCE cable RS449 DTE cable Figure 2-10 RS449 DTE cable RS449 DCE cable Figure 2-11 RS449 DCE cable RS530 DTE cable...

  • Page 36: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-13 RS530 DCE cable For the pinouts of synchronous/asynchronous serial cables (with DB-28 connectors), see Low-End and Mid-Range Series Routers Cable Manual. Note: These cables are optional items.

  • Page 37: Sic-1Epri/Sic-1E1-F

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.3 SIC-1EPRI/SIC-1E1-F 2.3.1 Introduction 1-port channelized E1/CE1/PRI compatible interface card (SIC-1EPRI) supports: Transmission/Receiving and handling of E1 data streams; CE1 (channelized E1) access; ISDN PRI function;...

  • Page 38: Dip Switch

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.3.3 DIP Switch E1/CE1/PRI interface is compatible with both 75-ohm impedance and 120-ohm impedance. The interface matches different types of impedance through an 8BIT DIP switch.

  • Page 39: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 75-ohm 120-ohm DIP switch Description impedance impedance OFF: RxShield grounding via Switch for capacitor 8BIT RxShield — grounding options ON: RxShield directly grounding Caution: When setting internal DIP switch, you are recommended to: turn ON all BITs from 1 to 8 when a 75-ohm cable is connected.

  • Page 40: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-7 Description of the LEDs on SIC-1EPRI/SIC-1E1-F panel Description ON means carrier signal has been received. LINK OFF means no carrier signal has been received.

  • Page 41: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 120-ohm balanced twisted pair cable connects SIC-1EPRI/SIC-1E1-F with the DB-15 connector and network end with the RJ-45 connector. Note: A network interface connector is available for extending the E1 cable. Both ends of the connector are RJ-45 jacks that can be used to connect two 120-ohm balanced twisted pair cables.
  • Page 42 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Connect the BNC connector of the cable to the coaxial connector and the other end of the coaxial connector to the remote network equipment through a 75-ohm E1 trunk cable, if cable extension is needed.

  • Page 43: Sic-1Tpri/Sic-1T1-F

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Step 4: Check the status of LINK LED on the SIC-1EPRI/SIC-1E1-F panel: ON means the link is connected and OFF means the link is not connected. In the latter case, check the line.

  • Page 44: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Attribute Description Backup Supported service Terminal access ISDN (supported by SIC-1TPRI only) 2.4.3 Interface LEDs SIC-1TPRI panel is shown in the following figure: Figure 2-21 SIC-1TPRI panel...

  • Page 45: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.4.4 Interface Cable SIC-1TPRI/SIC-1T1-F interface cable is 100-ohm standard shielded network cable that RJ-45 connectors both ends. following figure illustrates SIC-1TPRI/SIC-1T1-F interface cable: Figure 2-23 T1 cable For the pinouts of T1 cable, see Low-End and Mid-Range Series Routers Cable Manual.

  • Page 46: Sic-1Am/Sic-2Am

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Step 3: Check the status of LINK LED on the SIC-1TPRI/SIC-1T1-F panel: ON means the link is connected and OFF means the link is not connected. In the latter case, check the line.

  • Page 47: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-25 SIC-2AM panel Table 2-11 Description of the LEDs on SIC-1AM/SIC-2AM panel Description OFF means the link is idle. ON means the connection has been LINK established.

  • Page 48: Sic-1Fxs/Sic-1Fxo & Sic-2Fxs/Sic-2Fxo

    SIC-FXO cards are loop trunk cards that provide access of common subscriber lines of exchanges. Caution: While using SIC-FXS/SIC-FXO, you must ensure that the H3C Routers can be connected to IP networks or other WANs. 2.6.2 Interface Attributes The interface attributes of SIC-1FXS/SIC-1FXO and SIC-2FXS/SIC-2FXO are given in...

  • Page 49: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Attribute Description Dialing mode Supports DTMF, not supports pulse dial-up. Bandwidth 300 Hz to 3400 Hz 2.6.3 Interface LEDs SIC-1FXS/SIC-1FXO panel Figure 2-26 SIC-1FXS panel...

  • Page 50: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-13 Description of the LEDs on SIC-1FXS/SIC-1FXO and SIC-2FXS/SIC-2FXO panels Description OFF means the link is idle. ON means the link is being occupied LINK for call connection.

  • Page 51: Sic-4Fsw/Sic-4Fsw-Poe/Dsic-9Fsw/Dsic-9Fsw-Poe

    2.7.1 Introduction SIC-4FSW/SIC-4FSW-PoE and DSIC-9FSW/DSIC-9FSW-PoE interface cards are 4/9-port 10/100 Mbps Ethernet Layer 2 SIC interface cards that can be used on H3C MSR 20/30/50 series routers. They provide up to 4/9 10/100 Base-Tx Ethernet ports for Layer 2 and Layer 3 switching. A router installed with SIC-4FSW/DSIC-9FSW modules...

  • Page 52: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Note: MDI stands for Media Dependent Interface of the Ethernet. Normally, the interfaces on the network cards belong to this type. MDIX stands for Cross Media Dependent Interface, which is usually adopted on HUBs or LAN Switches.

  • Page 53: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-32 Ethernet cable Ethernet cables fall into two categories: straight-through cables and crossover cables, specifically, Straight-through cable: the wire sequences of the twisted pair cable crimped in the RJ-45 connectors at both ends are completely the same.

  • Page 54: Interface Attributes

    1000/100/10 Mbps on electrical interface; 1000 Mbps on fiber interface Note: For H3C MSR 20-40 and MSR 30/50 series routers, a SIC-1GEC interface card can only be installed in SLOT2 or SLOT4. 2.8.2 Interface Attributes The attributes of SIC-1GEC interface are shown in the following table.

  • Page 55: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-17 Attributes of SFP module Maximum SFP module Fiber Wavelength Connector transmission name specification distance 50/125 µm 550 m (1804.5 multi-mode ft.) fiber...

  • Page 56: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards The following table describes the electrical interface LEDs on the left of the SIC-1GEC panel. Table 2-18 LEDs for the electrical interface on the left of the SIC-1GEC panel Description ON means carrier signal is received;...

  • Page 57: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Crossover cable: The wire sequences of twisted pair cable crimped in the RJ-45 connectors at both ends are different. It can be used to connect two terminal devices (such as PCs and Routers).

  • Page 58: Sic-1Ve1

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Step 2: Check the status of LINK LED on the GEC panel: ON means the link is connected and OFF means the link is not connected. In the latter case, check the line.

  • Page 59: Dip Switches

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Attribute Description Operation mode ISDN PRI (only supported by SIC-1VE1) Backup Services Terminal access ISDN (only supported by SIC-1VE1) 2.9.3 DIP Switches CE1/PRI/R2 interface is compatible with 75-ohm and 120-ohm impedance. Matching of different impedance is implemented through an 8BIT DIP switch.

  • Page 60: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Configuration of Configuration of Description 75-ohm 120-ohm impedance impedance OFF: RxRing is grounded via RxRing grounding capacitance. mode selection 6BIT — switch ON: RxRing is grounded directly.

  • Page 61: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-22 LEDs for the electrical interface on the left of SIC-1GEC panel Description ON means carrier signal is received; LINK OFF means no carrier signal is received.

  • Page 62: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 120-ohm balanced twisted pair cable connects SIC-1VE1 with the DB-15 connector and network end with the RJ-45 connector. Note: A network interface connector is available for extending the E1 cable. Both ends of the connector are RJ-45 jacks that can be used to connect two 120-ohm balanced twisted pair cables.
  • Page 63 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Connect the BNC connector of the cable to the coaxial connector and the other end of the coaxial connector to the remote network equipment through a 75-ohm E1 trunk cable, if cable extension is needed.

  • Page 64: Sic-1Vt1

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.10 SIC-1VT1 2.10.1 Introduction 1-port T1 voice interface card (SIC-1VT1) can handle dense voice signals in VoIP system. It provides a CT1/PRI/R2 port, allowing the access of 23 channels of voice signals.

  • Page 65: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.10.3 Interface LEDs The following figure illustrates the SIC-1VT1 panel. Figure 2-41 SIC-1VT1 panel The following table describes the LEDs on the SIC-1VT1 panel.

  • Page 66: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Caution: The corresponding cables are not included in the standard shipment package of SIC-1VT1. Please order them together with SIC-1VT1. By default, they are not supplied.

  • Page 67: Interface Attributes

    Trellis coding (except for G. Lite) on ADSL interfaces, enhancing the stability of ADSL connection. Note: For H3C MSR 20-40 and MSR 30/50 series routers, a SIC-1ADSL interface card can only be installed in SLOT2 or SLOT4. 2.11.2 Interface Attributes...

  • Page 68: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-43 SIC-1ADSL panel The following table describes the LEDs on the card panel. Table 2-26 LEDs on the SIC-1ADSL panel Description OFF means the loop is inactive.

  • Page 69: Sic-1Adsl-I

    A G.992.1-compliant interface, auto-sensing. Trellis coding on ADSL interfaces, enhancing the stability of ADSL connection. Note: For H3C MSR 20-40 and MSR 30/50 series routers, a SIC-1ADSL-I interface card can only be installed in SLOT2 or SLOT4. 2.12.2 Interface Attributes The following table describes the interface attributes of the SIC-1ADSL-I.

  • Page 70: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-27 Interface attributes of the SIC-1ADSL-I Attribute 1ADSL-I Connector RJ-11 Number of connectors ITU-T 992.1 G.DMT ANSI T1.413 Issue 2 Interface standard ITU-T 992.3 ITU-T 992.5...

  • Page 71: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Note: The standard equipping package for the SIC-1ADSL-I includes a regular telephone cable, but the splitter needs a separate order. 2.12.5 Connecting the Interface Cable To connect the interface on the SIC-1ADSL-I card, you need to install a splitter.

  • Page 72: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-29 Interface attributes of SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU. Attribute Description SIC-1BS/SIC-2BS: RJ45 Connector SIC-1BU/SIC-2BU: RJ45 or RJ11. 1 (SIC-1BS/ SIC-1BU) Number of connectors 2 (SIC-2BS/ SIC-2BU)

  • Page 73: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Figure 2-50 SIC-2BU panel The following table describes the LEDs on SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU panels. Table 2-30 LEDs on SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU panels. Description OFF indicates the B1 channel is idle.

  • Page 74: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.13.5 Connecting the Interface Cable Caution: When connecting the interface cable, pay attention to the mark on the interface to avoid wrong insertion, which may damage the interface card or even the router host.

  • Page 75: Interface Attributes

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards mode. In the upstream direction, the SIC-1BSV/SIC-2BSV card can be connected to a user interface on an ISDN switch to receive and decompress, compress and transmit ISDN BRI digital voice traffic.

  • Page 76: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.14.3 Interface LEDs The following figure illustrates the SIC-1BSV panel. Figure 2-51 SIC-1BSV panel The following figure illustrates the SIC-2BSV panel. Figure 2-52 SIC-2BSV panel The following table describes the LEDs on SIC-1BSV/SIC-2BSV panel.

  • Page 77: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Green Yellow Green Yellow Green Yellow Green Yellow Green Green Green Green Yellow Yellow Yellow Yellow Red Black Red Black Red Black Red Black...

  • Page 78: Sic-1Fef

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards To connect the interface card to an ISDN network, identify the type of the ISDN line provided by your telecommunications service provider. If the line is an ISDN U-interface line, use an NT1 for conversion. Insert one end of the straight-through S/T interface cable into the S/T interface of the NT1, and the other end into the BSV interface of the SIC-1BSV/SIC-2BSV interface card.

  • Page 79: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Attribute Description Single-m Multimode Ultra-long Long-haul Long-haul medium- short-haul haul (1550 haul (1310 nm) (1550 nm) (850 nm) (1310 Optical Optical Optical Optical Trans...

  • Page 80: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Table 2-34 LEDs on SIC-1FEF panel Status Description No link is present. The SFP optical module has established a Steady green 100 Mbps link.

  • Page 81: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.15.5 Connecting the Interface Cable Caution: When connecting the optical fiber, observe the following: Do not over-bend the optical fiber. Its curvature radius must be no less than 10 cm (3.9 in).

  • Page 82: Interface Attributes

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.16.2 Interface Attributes The following table describes the interface attributes of SIC-8AS. Table 2-35 Interface attributes of SIC-8AS Attribute Description Connector DB60 Number of connectors...

  • Page 83: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards 2.16.4 Interface Cable The SIC-8AS uses the customized cable, which is illustrated by the following figure: Figure 2-58 Customized cable Caution: This customized cable is optional. You need to order it when you purchase a SIC-8AS card.
  • Page 84 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 2 Smart Interface Cards Step 2: Plug one end of the AUX cable, the DB60 connector, to the router and fasten the screws on the connector, and plug the other end of the cable to the Modem or terminal.

  • Page 85: Chapter 3 Multifunctional Interface Modules

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Chapter 3 Multifunctional Interface Modules For the modular MSR series routers, a wide range of optional MIM/DMIM multifunctional interface modules are available, which provide abundant interfaces, such as synchronous/asynchronous serial interface, Ethernet interface, E1/T1, ISDN BRI/PRI, audio interface, Layer 2 switching interface, and so on.

  • Page 86: Interface Leds

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.1.3 Interface LEDs MIM-1FE panel is shown in the following figure: Figure 3-1 MIM-1FE panel MIM-2FE panel is shown in the following figure: Figure 3-2 MIM-2FE panel...

  • Page 87: Connecting The Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-4 Ethernet cable II. Making Ethernet cable Category 5 twisted pairs are adopted for making Ethernet cables. Each category 5 twisted pair is composed of 8 cores that are identified and grouped by color of insulation sheath.

  • Page 88: Mim-1Gbe/Mim-2Gbe Module

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.2 MIM-1GBE/MIM-2GBE Module 3.2.1 Introduction 1-port 10Base-T/100Base-TX/1000Base-T Ethernet electrical interface module (MIM-1GBE) and 2-port 10Base-T/100Base-TX/1000Base-T Ethernet electrical interface module serve to complete the communication between a router and a LAN.

  • Page 89: Interface Cable

    Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-6 MIM-2GBE The following table describes the LEDs on the MIM-1GBE/MIM-2GBE panel. Table 3-4 Description of the LEDs on the MIM-1GBE/MIM-2GBE panel Description LINK OFF means no link is present;...
  • Page 90 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.3 MIM-1GEF/MIM-2GEF Module 3.3.1 Introduction MIM-1GEF/MIM-2GEF is short for 1/2-port 1000Base-SX/1000Base-LX GE fiber interface module, where GE is short for Gigabit Ethernet and F for fiber, indicating optical fiber interface.
  • Page 91 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Description Attribute MIM-1GEF MIM-2GEF 9/125 9/125 9/125 9/125 62.5/125 m Fiber type single single single multi-mode single mode mode mode mode Max. 0.55 transmission (6.21...
  • Page 92 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.3.4 Interface Cable For MIM-1GEF/MIM-2GEF, select fiber-optic depending on the type of the installed 1000Base-SX/1000 Base-LX SFP. As the interfaces provided by these SFP modules use LC-type fiber-optic connectors, you must use fibers with LC connectors for them.
  • Page 93 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Warning: Laser danger: Invisible laser radiation may be emitted from the fiber-optic ports which are connected to lasers. To protect your eyes against radiation harm, never stare into an open fiber-optic port.
  • Page 94 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Description Attribute Synchronous Asynchronous Maximum baud rate 64 k 2.048 M 115.2 (bps) V.24 (RS232) DTE cable V.24 (RS232) DCE cable V.35 DTE cable V.35 DCE cable...
  • Page 95 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-8 Description of the LEDs on the MIM-2SAE/MIM-4SAE panel Description LINK OFF means no link is present; ON means a link is present.
  • Page 96 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-14 V.24 DTE cable V.24 DCE cable Figure 3-15 V.24 DCE cable V.35 DTE cable Figure 3-16 V.35 DTE cable V.35 DCE cable Figure 3-17 V.35 DCE cable...
  • Page 97 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-18 X.21 DTE cable X.21 DCE cable Figure 3-19 X.21 DCE cable RS449 DTE cable Figure 3-20 RS449 DTE cable RS449 DCE cable...
  • Page 98 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-22 RS530 DTE cable RS530 DCE cable Figure 3-23 RS530 DCE cable For the pinouts of synchronous/asynchronous serial cables (with DB-28 connectors), see Low-End and Mid-Range Series Routers Cable Manual.
  • Page 99 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Caution: Before connecting an SAE module, confirm the model of the equipment to be connected (that is, the synchronous/asynchronous mode, DTE/DCE mode, and so on), signaling criterion required by the access equipment, baud rate, and timing clock.
  • Page 100 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Description Attribute MIM-8ASE module MIM-16ASE module Minimum baud rate (bps) Maximum baud rate (bps) 115.2 k 1) Dialup through Modem 2) Backup Service supported...
  • Page 101 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Caution: AUX cable is optional. When ordering an MIM-8ASE or MIM-16ASE module, please order an AUX cable also. By default, it is not provided. As for dumb terminal cables, you can make them on site by reference to Low-End and Mid-Range Series Routers Cable Manual.
  • Page 102 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 8ASE/16ASE dumb 8ASE/16ASE dumb Standard Standard Dumb terminal adapter Dumb terminal adapter terminal cable terminal cable network cable network cable Dumb Dumb adapter adapter Figure 3-26 Connecting MIM-8ASE/MIM-16ASE cable to a dumb terminal Step 3: Check the behavior of the LINK LED on the MIM-8ASE/MIM-16ASE panel.
  • Page 103 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-10 Interface attributes of MIM-1E1/MIM-2E1/MIM-4E1 and MIM-1E1-F/MIM-2E1-F/MIM-4E1-F Description Attribute MIM-1E1/1E1-F MIM-2E1/2E1-F MIM-4E1/4E1-F module module module Connector DB-15 DB-15 DB-25 Number connectors Interface G.703, G.704...
  • Page 104 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-28 MIM-2E1 panel MIM-4E1 and MIM-4E1-F panels are similar. The following figure illustrates an MIM-4E1 module. Figure 3-29 MIM-4E1 panel The following table describes the LEDs on MIM-1E1/MIM-2E1/MIM-4E1 and...
  • Page 105 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-30 E1 75-ohm unbalanced coaxial cable Note: You can select a pair of coaxial connectors with a BNC receptacle at both ends that connect two 75-ohm unbalanced coaxial cables with BNC connectors.
  • Page 106 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules For the pinouts of E1 cables, see Low-End and Mid-Range Series Routers Cable Manual. Caution: E1 cable, coaxial connector, network interface connector and 75-ohm to 120-ohm adapter are all optional accessories.
  • Page 107 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Figure 3-33 75-ohm 4E1 conversion cable Caution: Both 75-ohm 4E1 and 120-ohm 4E1 conversion cables are required for MIM-4E1/4E1-F modules. While E1 cable is optional, please order E1 cables when purchasing an MIM-4E1 or MIM-4E1-F module.
  • Page 108 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules default, switches MIM-1E1/MIM-2E1/MIM-4E1 MIM-1E1-F/MIM-2E1-F/MIM-4E1-F modules are set to ON, as illustrated in the following figure: Figure 3-34 Default setting of DIP switches for MIM-1E1/MIM-2E1/MIM-4E1 and...
  • Page 109 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Configuration of Configuration of Description 75-ohm 120-ohm impedance impedance OFF: RxShield is grounded SxShield capacitance grounding mode 8BIT — selection switch ON: RxShield is grounded directly.
  • Page 110 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Step 3: Connect the other end of the E1 cable to the network device; When using 75-ohm unbalanced coaxial cable, Connect its BNC connector to the device to be connected directly, if cable extension is not needed;...
  • Page 111 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules DB-15 Network RJ-45 RJ-45 devices such Router as DDN Network interface connector 120-ohm balanced twisted pair 120-ohm E1 trunk cable Figure 3-36 Extending an E1 120-ohm balanced twisted pair cable Step 4: Check the behavior of the LINK LED on the module panel.
  • Page 112 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.7 MIM-8E1/MIM-8E1-F Module 3.7.1 Introduction I. MIM-8E1 module MIM-8E1, the 8-port channelized E1/PRI interface module, transmits, receives, and processes eight channels of E1 data traffic. In addition, you can use the module for other purposes, such as CE1 access and the ISDN PRI function.
  • Page 113 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Description Attribute MIM-8E1/MIM-8E1-F module MIM-8E1/MIM-8E1-F module (75-ohm) (120-ohm) Cable characteristic 75-ohm 120-ohm impedance E1, CE1, ISDN PRI (only supported by MIM-8E1) Operating mode FE1 (only supported by MIM-8E1-F)
  • Page 114 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.7.4 Interface Cable The MIM-8E1/MIM-8E1-F module provides eight E1 ports and adopts a 120-ohm or a 75-ohm 8E1 conversion cable. The two types of cables look similar. Both of them have a DB-68 connector at one end for connecting the router.
  • Page 115 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.7.5 Connecting the Interface Cable Caution: Before you connect a port, read its label carefully; a wrong connection can impair the interface module and even damage the device.
  • Page 116 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules where n=1-24. However, a CT1 module allows of arbitrary grouping of the 24 channels; T1-F does not support PRI mode. Note: Given a MIM-1T1 module, the system automatically creates a serial interface for each timeslot bundle formed on a controller T1 interface.
  • Page 117 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.8.3 Interface LEDs MIM-1T1 panel is similar to that of MIM-1T1-F. The following figure shows a MIM-1T1 panel. Figure 3-41 MIM-1T1 panel MIM-2T1 panel is similar to that of MIM-2T1-F, and they differ only in module name. The following figure shows a MIM-2T1 panel.
  • Page 118 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.8.4 Interface Cable Interface cables cables) MIM-1T1/MIM-2T1/MIM-4T1 MIM-1T1-F/MIM-2T1-F/MIM-4T1-F modules are 100-ohm straight-through shielding network cables, as shown in the following figure: Figure 3-44 T1 cable In addition, you may use a network interface connector to extend a T1 cable.
  • Page 119 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules directly if the cable is long enough; or after extending the cable if it is not long enough, as shown in the following figure:...
  • Page 120 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.9.2 Interface Attributes The interface attributes of the MIM-8T1 and the MIM-8T1-F are given in the following table: Table 3-18 Interface attributes of the MIM-8T1 and the MIM-8T1-F...
  • Page 121 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-19 Description of the LEDs on the MIM-8T1/MIM-8T1-F panel Description LINK OFF means no link is present; ON means a link is present.
  • Page 122 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Step 2: Connect one RJ-45 connector at the other end of the cable to the device to be connected. Step 3: Power on the router. Check the behavior of the LINK LED on the module panel.
  • Page 123 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Attribute Description Operating mode Supported service E3 leased line 3.10.3 Interface LEDs MIM-1CE3 panel is shown in the following figure: Figure 3-48 MIM-1CE3 panel...
  • Page 124 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Note: MIM-1CE3 and 1CT3 adopt the same cable, which is called E3/T3 cable in this manual. The standard shipment package of MIM-1CE3 does not include the interface cable.
  • Page 125 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Note: T3 represents the tertiary group rate of T system in the TDM system, that is, 44.736 Mbps. A T3 channel can be channelized into 28 T1 lines through the demultiplexing processes of T23 and T12, each T1 line also supporting the operating modes of CT1.
  • Page 126 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules The following table describes the LEDs on the MIM-1CT3 panel: Table 3-23 Description of the LEDs on the MIM-1CT3 panel Description ON means the carrier signal has been received.
  • Page 127 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-24 Interface attributes of the MIM-4BSE Attribute Description Connector RJ-45 Number of connectors Cable ISDN S/T cable Protocol & standard ITU-T I.430, Q.921, Q.931...
  • Page 128 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-25 Set the jumpers on the MIM-4BSE Jumper settings & description Default To use a 100-ohm matched resistance for data transmission, place the jumper over pins 1 and 2.
  • Page 129 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.12.4 Interface LEDs The following figure illustrates the MIM-4BSE panel. Figure 3-52 MIM-4BSE panel The following table describes the LEDs on the module panel.
  • Page 130 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.12.6 Connecting the Interface Cable Caution: If outdoor cabling is involved, consider to install a special lightning arrester at the input end of the interface cable for better lightning protection.
  • Page 131 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-27 Interface attributes of MIM-1G.SHDSL module Attribute MIM-1G.SHDSL module Connector RJ11 Number of connectors Interface standard G.991.2 In single-pair mode, supports the sending/receiving...
  • Page 132 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.13.5 Connecting the Interface Cable You only need a telephone cable to connect one port on a G.SHDSL module to the PSTN network. 3.14 MIM-1AMM/MIM-1ASM/MIM-1ASL 3.14.1 Introduction...
  • Page 133 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules MIM-1AMM MIM-1ASM MIM-1ASL Attribute module module module Central 1310 nm wavelength ATM Traffic CBR (Constant Bit Rate), rt_VBR (Variable Bit Service Rate-Real Time), nrt_VBR (Variable Bit Rate-Non Real Time), UBR (Unspecified Bit Rate) 3.14.3 Interface LEDs...
  • Page 134 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.14.4 Interface Optical Fiber MIM-1AMM uses multi-mode optical cable and MIM-1ASM/MIM-1ASL uses single-mode optical cable. As all these three modules adopt SC optical fiber connector, the connector of the connection cable should also be SC connector.
  • Page 135 Note: You are allowed to equip an H3C Series Router with MIM-AE3 modules to its full capacity. Yet, you are recommended to install only one MIM-AE3 module on it, whatever its model is, to ensure the performance of some key services.
  • Page 136 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules The following table describes the LEDs on the MIM-1AE3 panel: Table 3-32 Description of the LEDs on the MIM-1AE3 panel Description LINK OFF means no link is present; ON means a link is present.
  • Page 137 Note: You are allowed to equip an H3C Series Router with MIM-AT3 modules to its full capacity. Yet, you are recommended to install only one MIM-AT3 module on it, whatever its model is, to ensure the performance of some key services.
  • Page 138 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Note: In the supported services described in the above table, CBR represents Constant Bit Rate, rt_VBR represents Variable Bit Rate-Real Time, nrt_VBR represents Variable Bit Rate-Non Real Time, and UBR represents Unspecified Bit Rate.
  • Page 139 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.16.5 Connecting the Interface Cable Caution: Some measures have been taken to protect MIM-1AT3 module. To achieve better lightning protection effects, however, you are recommended to add a special lightning arrester at the input end of the E3/T3 cable when leading it to the outdoors.
  • Page 140 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Attribute MIM-1POS Interface rate 155.52 Mbps Multi-mode Single mode Single mode Single mode Type Trans short-haul medium-haul long-haul ultra-long haul mitting optical Min. –19.0 dBm –15.0 dBm...
  • Page 141 2/4 channels of E&M analog trunks. These modules make it possible to transfer voice signals over data communication networks. Caution: When connecting a voice MIM, make sure that H3C Series Routers can be connected to an IP network or other LAN. 3-57...
  • Page 142 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.18.2 Interface Attributes interface attributes MIM-2FXS/MIM-2FXO/MIM-2E&M MIM-4FXS/MIM-4FXO/MIM-4E&M modules are given in the following table: Table 3-37 Interface attributes of MIM-2FXS/MIM-2FXO/MIM-2E&M and MIM-4FXS/MIM-4FXO/MIM-4E&M Attribute Description...
  • Page 143 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules LINK Figure 3-64 MIM-2E&M panel LINK Figure 3-65 MIM-4FXS panel LINK Figure 3-66 MIM-4FXO panel LINK Figure 3-67 MIM-4E&M panel Table 3-38 Description of the LEDs on voice MIM panels...
  • Page 144 Series Routers Cable Manual. II. Interface cable of E&M modules E&M modules of H3C Series Routers support Bell I, II, III, V switches, and 2-wire & 4-wire voice signals. It is recommended to use Bell V 4-wire voice signal to communicate with the Router in practice.
  • Page 145 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Table 3-39 Pinouts of E&M interface cable (Bell V 4-wire) Router side Signal at switch side (Bell V 4-wire) RJ-45 Pin RJ-45 interface signal SB (negative power supply) —...
  • Page 146 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.18.5 Connecting the Interface Cable Caution: Some measures are taken to protect MIM-2FXS/MIM-2FXO/MIM-2E&M and MIM-4FXS/MIM-4FXO/MIM-4E&M. Still, you are recommended to install a special lightning arrester at the input end of each connection cable to obtain better lightning protection effect when the cable is led outdoors;...
  • Page 147 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules 3.19.2 Interface Attributes Table 3-40 MIM-HNDE module features Feature Description Protocol supported IPSec 1) key algorithm (DES, 3DES, AES) Hardware algorithm Authentication algorithm (HMAC-MD5-96, HMAC-SHA-1-96) 3.19.3 Interface LEDs...
  • Page 148 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Symptom 2: The ACTIVE LED stays off when powering on the router. Troubleshooting: When powering up the device, the ACTIVE LED should flashing for two seconds before turning off, which indicates the encryption processor of the MIM-HNDE module has been configured and is ready for work.
  • Page 149 Interface Card and Interface Module Manual H3C MSR 20/30/50 Series Routers Chapter 3 Multifunctional Interface Modules Attribute Description Operating mode ISDN PRI Interface rate 2.048 Mbps E1 120-ohm balanced twisted pair cable Cable 75ohm-to-120ohm adapter 1) R2 signaling 2) DSS1 signaling...

This manual is also suitable for:

Msr 30 seriesMsr 50 seriesSic-1gecSic-1feaSic-1fefSic-4fsw ... Show all

Table of Contents