Inglesina Fast Instruction Manual page 13

prevent the formation of rust.
• Keep all moving parts clean and, if necessary, lubricate
them with light oil.
• To facilitate reassembly, be sure to make a note of how the
different parts fit together before dismantling the product. In
caso di dubbio fai sempre riferimento alle istruzioni.
HINTS FOR CLEANING THE TEXTILE LINING
• It is recommended to wash the lining separately from
other items.
• Periodically revive the fabric parts using a soft clothes
brush.
• Follow the lining washing instructions on the labels.
LIST OF COMPONENTS
fig. 1
A Brackets
B Clamps
C Support Arms
D Front safety strap
E Waist safety Belt
F Central Buckle
G Crotch strap
H Lining
I Locking Pins
J Backrest pipe
K Seat Pad
ASSEMBLY OF THE SUPPORT ARMS
fig. 2 The support arms (C) are delivered disassembled.
fig. 3 Place the plastic rings of the front safety strap (D)
over the support arms (C). Slide the support arms (C) into the
frame of the table mounted chair.
fig. 4 The spring loaded locking pins (I) should "click"
through the corresponding holes in order to lock the support
arms (C) in place.
WARNING! After having locked the support arms (C), always
make sure that the locking pins (I) are properly engaged by
pulling at the same time the backrest and each arm (A).
fig. 5 Button both the lining ends around the support
arms (C).
POSITIONING CHAIR
fig. 6 Place the table mounted chair close to the table.
Push the table mounted chair all the way forward to the
edge of the table. The entire bottom surface of the arms (A)
must be in full contact with the top of the table. Confirm the
support arms (C) are properly in place under the table.
fig. 7 Screw the clamps
counterclockwise until reaching the bottom of the table.
Tighten the clamps (B) at least three (3) full turns after the
clamp first contacts the bottom of the table.
WARNING! Confirm that the table mounted chair is
securely anchored to the table by trying to pull it away
from the table and downwards. Do not place a child in the
table mounted chair if chair moves at all during this test.
fig. 8 WARNING! Never attach the table mounted
chair to table tops with beveled, angled or other
decorative profiles more than 3.5 cm, even if the clamps
(B) fully contact the underside of the table. There is a risk
the table mounted chair will detach from the table.
INSTRUCTIONS
(B) by rotating them
Handwash in cold water
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
• Dry the textile lining completely before using or storing it.
fig. 9 WARNING! Never attach the table mounted
chair to a table with profiles that do not ensure full
contact between the entire surface of the brackets (A)
and the top of the table, and the clamps (C) with the
bottom of the table. There is a risk the table mounted
chair will detach from the table.
SAFETY BELTS
fig. 10 Always secure the child with the waist belt (E).
Insert the two clips on the ends of the waist belt (E) into the
central buckle (F) attached to the crotch strap (G).
fig. 11 Loop the end of the crotch strap (G) over the
central buckle (F).
fig. 12 Always use the crotch together with the waist belt
and properly tighten the waist belt after placing the child in
the table mounted chair.
WARNING! The failure to follow this step may cause
the child to fall or slide out of the table mounted chair,
resulting in personal injury.
CLOSING AND REMOVING THE CHAIR
fig. 13 Unhook the waist belt (E). Confirm that the child's
feet and legs are free from the table mounted chair support
arms or any parts of the table (C). Remove the child from the
table mounted chair.
fig. 14 Loosen the clamps (B) by rotating them clockwise.
Remove table mounted chair by pulling it away from the
table.
fig. 15 Rotate the support arms (C) inward and upward for
storage.
REMOVING THE LINING
fig. 16 Unbutton the lining (H) off the support arms (C).
Push the locking pins (I) on the table mounted chair arms
inwards and pull away the two support arms (C).
fig. 17 Remove the plastic rings of the front safety strap
(D) from the ends of the support arms (C).
fig. 18 Remove the backrest pipe (J) from the lining (H).
fig. 19 Then, remove the seat pad (K) from the bottom of
the table mounted chair.
To re-assemble to table mounted chair, follow these steps in
reverse order.
TRANSPORT BAG
fig. 20 The table mounted chair is equipped with a
convenient integrated transport bag (L).
13