Table of Contents
Advertisement
Quick Links
Page 1 of 12
CR0079
FITTING INSTRUCTIONS FOR CR0079 OFFSET COTTON REELS
FOR YAMAHA XTZ 700 (TENERE) 2019-
PICTURE A
PICTURE B
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF
OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
.
WAY OF MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for R&G CR0079
Summary of Contents for R&G CR0079
- Page 1 Page 1 of 12 CR0079 FITTING INSTRUCTIONS FOR CR0079 OFFSET COTTON REELS FOR YAMAHA XTZ 700 (TENERE) 2019- PICTURE A PICTURE B HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY...
-
Page 2: Tools Required
Page 2 of 12 CR0079 TOOLS REQUIRED GENERAL TORQUE SETTINGS • M4 BOLT = 8Nm Socket set to include 27mm A/F socket and wrench. M5 BOLT = • Set of metric Allen keys or socket bits to M6 BOLT = include 8mm A/F size. - Page 3 Page 3 of 12 CR0079 LEFT-HAND SIDE ASSEMBLY RIGHT-HAND SIDE ASSEMBLY R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 4: Fitting Instructions
Page 4 of 12 CR0079 FITTING INSTRUCTIONS Please read all instructions before commencing fitting • Raise rear of bike we suggest lifting from the swing arm, support rear wheel (we suggest using blocks of wood) to prevent wheel from dropping when rear spindle is removed. - Page 5 Page 5 of 12 CR0079 NOTICE DE MONTAGE POUR CR0079 PROTECTION CRASH POUR YAMAHA XTZ 700 (TENERE) 2019- PHOTO A PHOTO B E KIT CONTIENT LES ARTICLES EN PHOTO ET ETIQUETTES SUR LA PAGE LES PARTIES PRESENTÉES PEUVENT ETRE UNIQUEMENT...
-
Page 6: Outils Requis
Page 6 of 12 CR0079 OUTILS REQUIS ALEURS DE SERRAGE M4 BOULON = 8N • M5 BOULON = 12N Clé à cliquet + douille 27mm. M6 BOULON = 15N • Clé Allen 8mm M8 BOULON = 20N • Clé dynamométrique... - Page 7 Page 7 of 12 CR0079 SCHEMA DE MONTAGE GAUCHE SCHEMA DE MONTAGE DROIT R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 8: Notice De Montage
Page 8 of 12 CR0079 NOTICE DE MONTAGE SVP, ’ LIRE L ENSEMBLE DE LA NOTICE AVANT DE ROCEDER AU MONTAGE • Relevez l'arrière de la moto, nous vous suggérons de le soulever au niveau du bras oscillant, de soutenir la roue arrière (nous suggérons d'utiliser des blocs de bois) pour éviter que la roue ne tombe lorsque l’axe arrière sera retiré. - Page 9 Page 9 of 12 CR0079 MONTAGEANLEITUNG FÜR CR0079 MONTAGESTÄNDER- AUFNAHMEN FÜR YAMAHA XTZ 700 (TENERE) 2019- ABBILDUNG A ABBILDUNG B EILE SIND AUF DEN FOLGENDEN SEITE ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST...
-
Page 10: Sie Benötigen Folgendes Werkzeug
Page 10 of 12 CR0079 SIE BENÖTIGEN FOLGENDES ALLGEM ANZUGSDREHMOMENTE WERKZEUG M4 SCHRAUBE = 8Nm • Satz Steckschlüssel inkl. 27mm A/F M5 SCHRAUBE = • Satz Inbusschlüssel oder Einsätze inkl. Gr. M6 SCHRAUBE = 8mm A/F M8 SCHRAUBE = 20Nm •... - Page 11 Page 11 of 12 CR0079 LINKE SEITE - ZUSAMMENBAU RECHTE SEITE – ZUSAMMENBAU R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 12 Page 12 of 12 CR0079 MONTAGEANLEITUNG Bitte die Montageanleitung komplett durchlesen, bevor Sie mit der Montage beginnen. • Das Heck anheben (wir empfehlen, von der Schwinge anheben) und das Hinterrad dabei stützen (wir empfehlen Holzblöcke), um zu vermeiden, dass das Rad runterfällt, wenn die hintere Radachse entfernt wird.
Need help?
Do you have a question about the CR0079 and is the answer not in the manual?
Questions and answers