Table of Contents
Advertisement
Quick Links
Page 1 of 15
CP0522
FITTING INSTRUCTIONS FOR CP0522 AERO CRASH PROTECTORS
HONDA CB125R 2021-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Advertisement
Table of Contents
Related Manuals for R&G CP0522
Summary of Contents for R&G CP0522
- Page 1 Page 1 of 15 CP0522 FITTING INSTRUCTIONS FOR CP0522 AERO CRASH PROTECTORS HONDA CB125R 2021- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
-
Page 2: Tools Required
Page 2 of 15 CP0522 TOOLS REQUIRED GENERAL TORQUE SETTINGS M4 BOLT = 8Nm SOCKET & WRENCH SET INCLUDING 13mm TO • M5 BOLT = 17mm SOCKETS. M6 BOLT = TORQUE WRENCH (UP TO 50Nm) • M8 BOLT = 20Nm SUITABLE SUPPORT JACK •... -
Page 3: Exploded Assembly View
Page 3 of 15 CP0522 EXPLODED ASSEMBLY VIEW FITTING PICTURES Picture 1 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... -
Page 4: Fitting Instructions
Page 4 of 15 CP0522 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting. - Page 5 Page 5 of 15 CP0522 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
- Page 6 Page 6 of 15 CP0522 NOTICE DE MONTAGE POUR CP0522 PROTECTIONS CRASH HONDA CB125R 2021- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
- Page 7 Page 7 of 15 CP0522 OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm CLÉ À CLIQUET + DOUILLES 13mm À 17mm • M5 BOULON = CLÉ DYNAMOMÉTRIQUE (À 50Nm) • M6 BOULON = RISE ADAPTÉE POUR SUPPORTER LE MOTEUR •...
-
Page 8: Vue D'ensemble
Page 8 of 15 CP0522 VUE D’ENSEMBLE PHOTOS DE MONTAGE Photo 1 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... - Page 9 Page 9 of 15 CP0522 NOTICE DE MONTAGE Avant de retirer les boulons du moteur, assurez-vous que la moto soit droite et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de bouger pendant le montage.
- Page 10 Page 10 of 15 CP0522 CONSUMER NOTICE The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
- Page 11 Page 11 of 15 CP0522 MONTAGEANLEITUNG FÜR CP0522 STURZPADS HONDA CB125R 2021- EILE SIND AUF DEN NACHFOLGENDEN EITEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST DASS ALLE EILE VORHANDEN SIND ESEN IE DIE...
- Page 12 Page 12 of 15 CP0522 SIE BENÖTIGEN FOLGENDES WERKZEUG ALLGEM. ANZUGSDREHMOMENT M4 SCHRAUBE = 8Nm SATZ STECKSCHLÜSSEL INKL. 13mm BIS • M5 SCHRAUBE = 17mm STECKSCHLÜSSEL M6 SCHRAUBE = DREHMOMENTSCHLÜSSEL (BIS 50Nm) • M8 SCHRAUBE = 20Nm MONTAGESTÄNDER / HEBER •...
- Page 13 Page 13 of 15 CP0522 EXPLOSIONSZEICHNUNG - ZUSAMMENBAU MONTAGE – ABBILDUNGEN Abbildung 1 MONTAGEANLEITUNG Bevor Sie die Schrauben für den Motor entfernen, stellen Sie sicher, dass das Motorrad aufrecht steht und der Motor mit einem geeigneten Ständer/Heber unterhalb der Ölwanne gestützt wird.
-
Page 14: Montage
Page 14 of 15 CP0522 VORBEREITUNG: Stellen Sie einen passenden Motorradheber oder Montageständer mittig unter den Motor (mit • einem Stuck Holz oder Kunststoff zwischen dem Motor und dem Ständer). Ein kleines bisschen Druck an der Unterseite des Motors anwenden, um den Motor während der •... - Page 15 Page 15 of 15 CP0522 shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights. R&G RACING RETURNS POLICY (NON-FAULTY GOODS) Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary).