Advertisement
Quick Links
Page 1 of 12
FITTING INSTRUCTIONS FOR CP0526 AERO CRASH PROTECTORS
T
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
D
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
I
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
DUCATI MONSTER 950 (PLUS) 2021-
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
MOUNTING TO THE BIKE
THESE RUBBER WASHERS CAN BE THROWN AWAY
WWW.RG-RACING.COM
.
R&G Racing
www.rg-racing.com
CP0526
.
.
.
.
,
.
Email:
info@rg-racing.com
Advertisement
Related Manuals for R&G CP0526
Summary of Contents for R&G CP0526
- Page 1 Page 1 of 12 CP0526 FITTING INSTRUCTIONS FOR CP0526 AERO CRASH PROTECTORS DUCATI MONSTER 950 (PLUS) 2021- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
- Page 2 Page 2 of 12 CP0526 TOOLS REQUIRED GENERAL TORQUE SETTINGS M4 BOLT = 8Nm • SOCKET & WRENCH SET INCLUDING 17mm and M5 BOLT = 19mm SOCKETS. M6 BOLT = • TORQUE WRENCH (UP TO 50Nm) M8 BOLT = 20Nm •...
- Page 3 Page 3 of 12 CP0526 LHS & RHS EXPLODED ASSEMBLY VIEW FITTING PICTURES Picture 1 Picture 2 Picture 3 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 4: Fitting Instructions
Page 4 of 12 CP0526 FITTING INSTRUCTIONS Before removing engine bolts, ensure the bike is upright and supported by a suitable engine stand or jack placed under the sump of the motorbike to support the partial weight of the engine, this will prevent the engine from moving during fitting. - Page 5 Page 5 of 12 CP0526 NOTICE DE MONTAGE POUR CP0526 PROTECTIONS CRASH DUCATI MONSTER 950 (PLUS) 2021- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
- Page 6 Page 6 of 12 CP0526 TOOLS REQUIRED VALEURS DE SERRAGE M4 BOULON = 8Nm • Clé à cliquet + douilles 17mm et 19mm. M5 BOULON = • Clé dynamométrique (à 50Nm) M6 BOULON = • Prise des support M8 BOULON = 20Nm...
- Page 7 Page 7 of 12 CP0526 VUE D’ENSEMBLE CÔTÉ GAUCHE & DROIT PHOTOS DE MONTAGE Photo 1 Photo 2 Photo 3 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
-
Page 8: Notice De Montage
Page 8 of 12 CP0526 NOTICE DE MONTAGE Avant de retirer les boulons du moteur, assurez-vous que la moto soit bien droite et soutenue par un support moteur ou un cric approprié placé sous le carter de la moto pour supporter le poids partiel du moteur, cela empêchera le moteur de bouger pendant le montage. - Page 9 Page 9 of 12 CP0526 MONTAGEANLEITUNG FÜR CP0526 AERO STURZPADS DUCATI MONSTER 950 (PLUS) 2021- EILE SIND AUF DEN NACHFOLGENDEN EITEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST DASS ALLE EILE VORHANDEN SIND...
- Page 10 Page 10 of 12 CP0526 SIE BENÖTIGEN FOLGENDES WERKZEUG ALLGEM ANZUGSDREHMOMENT M4 SCHRAUBE = 8Nm • STECKSCHLÜSSELSATZ INKL. 15mm und M5 SCHRAUBE = 17mm STECKSCHLÜSSEL M6 SCHRAUBE = • DREHMOMENTSCHLÜSSEL (BIS 50Nm) M8 SCHRAUBE = 20Nm • HEBER ODER MONTAGESTÄNDER...
- Page 11 Page 11 of 12 CP0526 LINKE & RECHTE SEITE EXPLOSIONSZEICHNUNG - ZUSAMMENBAU MONTAGE ABBILDUNGEN Abbildung 1 Abbildung 2 Abbildung 3 R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
-
Page 12: Montage
Page 12 of 12 CP0526 MONTAGEANLEITUNG Bevor Sie die Schrauben für den Motor entfernen, stellen Sie sicher, dass das Motorrad aufrecht steht und der Motor mit einem geeigneten Ständer/Heber unterhalb der Ölwanne gestützt wird. Dies verhindert, dass der Motor sich bei der Entfernung von Motorschrauben bewegt. WÄHREND DER INSTALLATION DÜRFEN DIE SCHRAUBEN FÜR DEN MOTOR NUR EINZELN UND NIE...
Need help?
Do you have a question about the CP0526 and is the answer not in the manual?
Questions and answers