Advertisement
Page 1 of 10
CP0504BL
FITTING INSTRUCTIONS FOR CP0504BL
AERO-STYLE CRASH PROTECTORS
KAWASAKI ZX-25R 2020-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for R&G CP0504BL
Summary of Contents for R&G CP0504BL
- Page 1 Page 1 of 10 CP0504BL FITTING INSTRUCTIONS FOR CP0504BL AERO-STYLE CRASH PROTECTORS KAWASAKI ZX-25R 2020- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
-
Page 2: Tools Required
Page 2 of 10 CP0504BL TOOLS REQUIRED GENERAL TORQUE SETTINGS • 14mm & 17mm A/F SOCKETS AND WRENCH M4 BOLT = 8Nm M5 BOLT = • TORQUE WRENCH (UP TO 40N/m) M6 BOLT = M8 BOLT = 20Nm 0 BOLT = 40Nm... - Page 3 Page 3 of 10 CP0504BL LHS ASSEMBLY EXPLODED VIEW RHS ASSEMBLY EXPLODED VIEW R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 4: Fitting Instructions
Page 4 of 10 CP0504BL FITTING INSTRUCTIONS • Before fitting the R&G crash protectors, it is advised that a jack is positioned underneath the bike at a suitable point to support the weight of the engine during fitment. A small piece of wood should also be placed between the jack and the mounting point to help to spread the load. - Page 5 Page 5 of 10 CP0504BL NOTICE DE MONTAGE POUR CP0504BL PROTECTIONS CRASH KAWASAKI ZX-25R 2020- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
-
Page 6: Outils Requis
Page 6 of 10 CP0504BL OUTILS REQUIS VALEURS DE SERRAGE RECOMMANDÉES • CLÉ À CLIQUET + DOUILLES 14mm & 17mm M4 BOULON = 8Nm • CLÉ DYNAMOMÉTRIQUE (À 40N/m) M5 BOULON = 12Nm M6 BOULON = 15Nm M8 BOULON = 20Nm... -
Page 7: Notice De Montage
Page 7 of 10 CP0504BL NOTICE DE MONTAGE • Avant de monter les protections crash R&G, il est conseillé de placer un cric sous la moto à un endroit approprié pour supporter le poids du moteur pendant le montage. Un petit morceau de bois doit également être placé... - Page 8 Page 8 of 10 CP0504BL MONTAGEANLEITUNG FÜR CP0504BL AERO-STURZPADS KAWASAKI ZX-25R 2020- EILE SIND UNTEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST DASS ALLE EILE VORHANDEN SIND ESEN IE DIE ONTAGEANLEITUNG KOMPLETT DURCH...
- Page 9 Page 9 of 10 CP0504BL SIE BENÖTIGEN FOLGENDES WERKZEUG ALLGEM. ANZUGSDREHMOMENT • 14mm & 17mm A/F STECKSCHLÜSSEL M4 SCHRAUBE = 8Nm M5 SCHRAUBE = • DREHMOMENTSCHLÜSSEL (BIS 40N/m) M6 SCHRAUBE = M8 SCHRAUBE = 20Nm 0 SCHRAUBE = 40Nm M12 SCHRAUBE = 40Nm...
- Page 10 Page 10 of 10 CP0504BL MONTAGEANLEITUNG • Bevor Sie die R&G Sturzpads montieren, empfehlen wir, einen Heber an einem geeigneten Montagepunkt unter das Motorrad zu stellen, um somit das Gewicht des Motors während der Montage zu stützen. Ein kleines Stück Holz sollte zusätzlich zwischen Montagepunkt und Heber platziert werden, um die Last zu verteilen.
Need help?
Do you have a question about the CP0504BL and is the answer not in the manual?
Questions and answers