Table of Contents
Advertisement
Quick Links
Page 1 of 6
C
LG0026CG/LH
FITTING INSTRUCTIONS FOR CLG0026CG/LH FACTORY CARBON LEVER DEFENDER
ZERO SRF 19-
PICTURE A
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PRECEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
T
(
).
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
Digital copies of these instructions are available to download from
www.rg-racing.com
R&G
Unit
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
Tel: +44 (0)
420 89007 Fax: +44 (0)
420 87301
www.rg-racing.com
Email:
info@rg-racing.com
1
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for R&G CLG0026CG/LH
Summary of Contents for R&G CLG0026CG/LH
- Page 1 Page 1 of 6 LG0026CG/LH FITTING INSTRUCTIONS FOR CLG0026CG/LH FACTORY CARBON LEVER DEFENDER ZERO SRF 19- PICTURE A THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. PLEASE READ ALL INSTRUCTIONS BEFORE PRECEEDING.
-
Page 2: Tools Required
Page 2 of 6 LG0026CG/LH TOOLS REQUIRED MAXIMUM TORQUE SETTINGS Set of Allen keys to include 4mm A/F. M4 BOLT = 8Nm M5 BOLT = 12Nm Whatever tools required to remove original bar- M6 BOLT = 15Nm end if applicable. M8 BOLT = 20Nm M10 BOLT = 40Nm M12 BOLT = 40Nm... -
Page 3: Fitting Instructions
Page 3 of 6 LG0026CG/LH FITTING INSTRUCTIONS To fit the Lever Guard (item 3) remove the original bar end. Place the counter-sunk bolt (item 1) through the small domed spacer (item 2) Lever Guard. Place the counter-sunk bolt with domed spacer through the Lever Guard (item 3). Place the conical spacer (item 4) over the thread and into the lever guard so the smaller diameter fits into the lever guard. - Page 4 Page 4 of 6 LG0026CG/LH INSTRUCTIONS DE MONTAGE POUR CLG0026CG/LH DEFENDER À LEVIER DE CARBONE D'USINE ZERO SRF 19- PHOTO A E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS...
-
Page 5: Outils Requis
Page 5 of 6 CLG0026CG/LH OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm Clé Allen 4mm. M5 BOULON = Un outil pour retirer l’embout de guidon M6 BOULON = d’origine. M8 BOULON = 20Nm 0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE... -
Page 6: Notice De Montage
Page 6 of 6 CLG0026CG/LH COMPOSANTS NOTICE DE MONTAGE Pour monter la protection (article 3), retirez l'extrémité de guidon d'origine. Placer le boulon (article 1) dans la petite entretoise bombée (article 2). Placer le boulon avec entretoise bombée à travers la protection de levier (article 3). - Page 7 Page 1 of 6 LG0026CG/RH FITTING INSTRUCTIONS FOR CLG0026CG/RH FACTORY CARBON LEVER DEFENDER ZERO SRF 19- PICTURE A THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. PLEASE READ ALL INSTRUCTIONS BEFORE PRECEEDING. IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
- Page 8 Page 2 of 6 LG0026CG/RH TOOLS REQUIRED MAXIMUM TORQUE SETTINGS Set of Allen keys to include 4mm A/F. M4 BOLT = 8Nm M5 BOLT = 12Nm Whatever tools required to remove original bar- M6 BOLT = 15Nm end if applicable. M8 BOLT = 20Nm M10 BOLT = 40Nm M12 BOLT = 40Nm...
- Page 9 Page 3 of 6 LG0026CG/RH FITTING INSTRUCTIONS To fit the Lever Guard (item 3) remove the original bar end. Place the counter-sunk bolt (item 1) through the small domed spacer (item 2) Lever Guard. Place the counter-sunk bolt with domed spacer through the Lever Guard (item 3). Place the conical spacer (item 4) over the thread and into the lever guard so the smaller diameter fits into the lever guard.
- Page 10 Page 4 of 6 LG0026CG/RH INSTRUCTIONS DE MONTAGE POUR CLG0026CG/RH DEFENDER À LEVIER DE CARBONE D'USINE ZERO SRF 19- PHOTO A E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N ETES PAS SUR QUE TOUTES LES PIECES SOIENT PRESENTES...
- Page 11 Page 5 of 6 CLG0026CG/RH OUTILS REQUIS VALEURS DE SERRAGE M4 BOULON = 8Nm Clé Allen 4mm. M5 BOULON = Un outil pour retirer l’embout de guidon M6 BOULON = d’origine. M8 BOULON = 20Nm 0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE ARTICLE No DESCRIPTION...
- Page 12 Page 6 of 6 CLG0026CG/RH COMPOSANTS NOTICE DE MONTAGE Pour monter la protection (article 3), retirez l'extrémité de guidon d'origine. Placer le boulon (article 1) dans la petite entretoise bombée (article 2). Placer le boulon avec entretoise bombée à travers la protection de levier (article 3). Placer l'entretoise conique (article 4) sur le filetage et dans la protection levier de sorte que le plus petit diamètre s'insère dans la protection de levier.
Need help?
Do you have a question about the CLG0026CG/LH and is the answer not in the manual?
Questions and answers