Audio Menu (Optional) - HotSpring HOT SPOT RELAY Owner's Manual

FILTER CYCLES
When the spa is first powered up, the automatic filter cycle will wait
10 minutes before starting. Your spa will automatically turn the first
filter cycle on for 60 minutes on low speed. The second filter cycle will
activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will
be displayed in the control panel during the filter cycle.
NOTE: When using @ease SmartChlor, the initial recommended
minimum filter cycle setting is 2 hours 30 minutes, twice a day (5 hours
POWER
total). You may adjust this setting based on your bather load.
NOTE: The optional FRESHWATER III ozone system only works during
the filter cycle.
To modify the length of either filter cycle: POWER
A. Press the MODE ( or ) button until the
TOOLS menu is displayed.
B. Press the (+) b utton to enter the TOOLS
POWER
submenus.
C. Press the MODE ( or ) button until
FILT1 or FILT2 is displayed.
D. Press the (+) b utton to enter FILT1 or
POWER
FILT2. F1 or F2 icon will flash.
E. Using the (+) or the (-) button, adjust the
desired filter cycle time, from 0 to 6 hours.
F. Press the MODE () button in FILT1 to go
POWER
to the RESET screen. Press the (+) b utton
if you want to reset the filter 1 starting time
to the current time or press the MODE ()
button to go the the EXIT screen. Press the
POWER
(+) b utton in the EXIT screen to go to the FILT2 screen.
The filter cycle will activate the jet pump on low speed for the entire
cycle. When activated, the filter cycle icon on the display is turned on.
If the temperature exceeds the set point by three degrees F for more
POWER
than three hours, the system will cancel the filter cycle for the remaining
filter cycle time. Should the temperature cool down to 1.5 degrees F (1
degree C) below the set point before the end of the cycle, the cycle will
resume for the rest of the time. Should you use the spa during the filter
cycle by placing the jet pump on high speed, the Filter icon and Jets icon
will be on. Once the jet pump has been shut off, a ten minute tranquil
mode begins (Filter & Jet icons are off during tranquil mode while F1
or F2 remain lit). The Filter and Jet icons will come back on once the
tranquil mode ends if the filter cycle timer is still on.
BRIGHTNESS - LCD
If you would like to change the brightness of the Control Panel screen:
A. Press the MODE ( or ) button until the TOOLS menu is
displayed.
B. Press the (+) b utton to enter the TOOLS
submenus.
C. Press the MODE ( or ) button until
LCD is displayed.
D. Press the (+) b utton to enter into the LCD menu.
E. Using the (+) or the (-) button, adjust the desired screen brightness.

AUDIO MENU (OPTIONAL)

The following applies to spas that have an optional wireless audio
system installed:
When the wireless audio system has been installed on the spa, the
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER POWER
POWER POWER
POWER POWER
Page 16
POWER
POWER
control panel can be used to control the audio system. The following
information demonstrates how to navigate the music menu by using the
spa's control panel.
AUDIO MENU
An AUDIO menu will be accessible on the
control panel screen.
To access the menu, press the MODE ( or
) button until AUDIO is displayed.
BASIC CONTROL PANEL OPERATION
1. To enter into a sub-menu press the (+) b utton.
2. To move to the next menu press the MODE () button
3. To exit from any sub-menu, press MODE ( or ) button as many
times as necessary until EXIT is displayed then press the (+) b utton
to exit that sub-menu.
TO TURN AUDIO SYSTEM ON/OFF
(OPTIONAL)
From the AUDIO screen:
1. Press the (+) b utton to display POWR -.
2. Press the (+) b utton to display POWR +
and turn the audio system ON. Press the
(-) b utton to
display PWR - and turn the audio system OFF.
IMPORTANT: The power can take a few seconds to turn on or off.
TO PAIR BLUETOOTH
On your device, find My Spa BTXR. If you DO NOT see this, another
device may already be connected (see To Disconnect Bluetooth on
following page).
1. Press the MODE ( or ) button until the SETUP screen is
displayed.
2. Press the (+) b utton to display one of three audio sources, BLUE,TV,
AUX in the setup menu. Bluetooth should be selected.
3. Press the MODE ( or ) button until the PAIR+ screen is
displayed.
4. Press the (+) b utton followed by pressing "connect" next to My Spa
BTXR on your device to pair.
After pairing, you will be ready to use your Bluetooth device. Only one
paired Bluetooth device will work at a time.
TO ADJUST VOLUME
From the AUDIO screen:
Press the (+) b utton to display POWR.
1.
2. Press the MODE () button to display
VOL.
3. Press the (+) b utton to increase volume and the (-) b utton to
decrease volume.
NOTE: Volume range is from 0-40. No number displayed indicates
Volume is OFF.
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
Operating Instructions
Operating Instructions
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER