Operating Instructions - HotSpring Gleam Owner's Manual

o I
peratInG nStructIonS
The control panel provides a quick visual check of the spa's status and
allows the user to set the temperature, activate the jets & lights, lock the
temperature and/or spa functions. Other optional functions may also be
available depending on the spa model and accessory equipment that
has been installed into the spa. The control panel has eight buttons.
HARD BUTTONS
The four labeled outer buttons are referred to as "Hard buttons". These
buttons are fixed and their functions do not change.
JETS - If jet pump indicator icon is off and JETS hard button is pressed,
the 1st jet pump function will activate and the Control panel display will
advance to the Jets menu.
If jet pump indicator icon is on and the JETS hard button is pressed while
in any screen other than the Jets menu, the jets pump function does not
change, only the Control panel screen will change to the Jets menu.
LIGHTS - If lights are off, press LIGHTS hard button from any screen to
turn on the Underwater lights (only) and display the Underwater Lighting
menu. When LIGHTS hard button is pressed in the Underwater Lighting
menu with the underwater lights on, it will cycle the light intensity for the
underwater lights. If underwater lights are on, initial press of LIGHTS
hard button will not change light setting but will access Underwater
lighting menu.
OPTIONS - Transitions to the Options screen to access temperature
and setup menu
BACK - Goes back one menu. In Home screen Hold BACK button until
screen rotates 180° to view from inside spa. Repeat to reverse.
JETS
Hard button
Soft buttons
Indicator Icons
OPTION
Hard button
Control panel screen
SOFT BUTTONS
The four inside buttons are referred to as "soft buttons". Pressing a soft
button will activate the function on the control panel screen closest to
that button. The control panel display lets you know you've pressed a
button and that the selected function has been performed. After a period
of non-use (45 seconds) the display will go back to the Home screen
where the screen will remain on for several minutes before going into
sleep mode. Pressing any button will wake up a sleeping display.

Operating Instructions

LIGHTS
Hard button
BACK
Hard button
Page 13
INDICATOR ICONS
The indicator icons can only be seen on the Home Screen. They are
visible whenever the icon's function is active.
READY Indicator: The READY indicator icon is displayed
when the spa water temperature is within 2°F (1°C) of the set
temperature, and will turn off when the temperature is outside of that
range. If you increase or decrease the temperature setting of the spa,
the ready indicator will turn off until the water temperature reaches the
acceptable range for the new temperature setting. A flashing READY
indicator means a problem may exists with the temperature sensor (see
Troubleshooting section for more information)
Spa Light Indicator: The Spa Light indicator icon is displayed
when any light inside the spa is on. The indicator will remain
solid as long as any light is activated. Spa Light indicator flashes
whenever the color wheel is on.
Spa or Temperature Lock Indicator: The Spa or Temperature
Lock indicator icon is displayed when either the Spa Lock,
Temperature Lock or both is activated. Lock indicator icon does not
flash.
Jet Pump Indicator: The Jet Pump indicator icon is displayed
whenever a jet pump is on. The Jet Pump indicator icon will
flash whenever the spa is in the ten-minute clean cycle.
Summer Timer Indicator: The Summer Timer indicator icon is
displayed when the summer timer is set to ON. In the summer
timer mode, the heater and circulation pump cycle are off for eight
hours. The Summer Timer indicator icon will not flash.
Water Care Indicator: The Water Care indicator icon is
displayed whenever a water care device is detected in the
system and the water care system is operating correctly. The icon will
flash if the water care system requires attention.
POWER Indicator: The POWER indicator icon is displayed
when the spa is properly supplied with power. It also provides
a diagnostic function–a flashing power indicator icon indicates that the
heater high limit has tripped, meaning that either the spa water is above
its acceptable temperature range, or a malfunction has occurred within
the spa (such as low circulation due to clogged filters). An 'off' power
indicator icon means that there is a problem with the spa control box or
the power supplied to the spa (see Troubleshooting section for more
information).
OPTION SCREEN
The Option screen is an intermediate
screen that gets you to various optional
settings.
Press the OPTIONS hard button on
the control panel to display the Options
screen.
Press the Soft button next to the descriptions to access the description's
screen.
IMPORTANT: Audio and ACE Water Care will only be displayed on your
Options screen if your spa is equipped with these features.