Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HotSpring HIGHLIFE
Summary of Contents for HotSpring HIGHLIFE
- Page 1 HIGHLIFE COLLECTION ® QUICKSTART GUIDE...
- Page 2 Your Hot Spring ® ���� Safely Connect Your Spa Congratulations on your purchase of a new Highlife® Collection spa! We are excited to welcome you to the If you haven’t already, hire or consult an electrician to safely Hot Spring family and look forward to becoming an connect your spa.
- Page 3 � Set the Water Temperature � Balance Your Water Use the control panel to set the temperature to your desired Dip a FreshWater® 5-Way Test 5-WAY TEST STRIP level, which should be at least 95°F (33°C). We recommend Strip into the water for two temperatures between 100°F (38°C) and 104°F (40°C).
-
Page 4: Using The Control Panel
Using the Control Panel Maintenance Tips Touch anywhere on the screen to turn on the control panel. Protect your investment for years to come with these important tips. 102 ˚ CARE FOR YOUR SPA SHELL AND COVER • A soft rag should easily remove most dirt from your spa’s shell. -
Page 5: Safety Information
READ ALL OF THIS IMPORTANT INFORMATION BEFORE SAFETY INSTRUCTIONS USING YOUR SPA READ ALL OF THIS Safety Information • Do not connect any auxiliary components (for example, cable additional INFORMATION BEFORE speakers, headphones, additional audio components) to the audio USING YOUR SPA system unless approved by WATKINS WELLNESS . - Page 6 • Persons taking medications which induce drowsiness, such as DANGER - RISK OF ELECTRICAL SHOCK tranquilizers, antihistamines, or anticoagulants should not use the spa. • Install at least 5 feet (1.5 m) from all metal surfaces. A spa may be installed within 5 feet (1.5 m) of a metal surface if each metal surface HEALTH PROBLEMS AFFECTED BY SPA USE is permanently connected by a minimum No.
-
Page 7: Important Spa Instructions
SPA SHELL AVOIDING THE RISK OF SKIN BURNS Your HOT SPRING spa has an acrylic shell. Stains and dirt generally will not adhere to your spa’s surface. A soft rag should easily remove • To reduce the risk of injury, before entering a spa the user should most dirt. -
Page 8: Electrical Information
ELECTRICAL INFORMATION HIGHLIFE / LIMELIGHT • The subpanel requires a 50 amp, single phase, 230 volt, four wire service (two line, one neutral, one ground). The grounding conductor must not be less than #10 AWG. Refer to local codes and to NEC 250- Electrical Requirements 122 table. -
Page 9: 230 Volt Converted Prism
ELECTRICAL INFORMATION SOVEREIGN, PRODIGY, JETSETTER LX & BEAM II 230 volt permanently connected model IMPORTANT! THE EXACT PHYSICAL LOCATION OF THE TERMINALS ON THE GFCI BREAKER WILL VARY BETWEEN MANUFACTURERS. CONNECTING THE HOT WIRE TO THE NEUTRAL TERMINAL WILL CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL BOX. FACTORY WIRED HEATER... -
Page 10: Installation Instructions
ELECTRICAL INFORMATION 115 VOLT JETSETTER & BEAM I INSTALLATION INSTRUCTIONS MODELS All 115 volt models come equipped with approximately 15 feet of useable power cord (this is the maximum length allowed by The Ground Fault Circuit Interrupter (GFCI) is a safety device that is Underwriters Laboratory and the National Electric Code). -
Page 11: Wiring Connections
ELECTRICAL INFORMATION Required Part: A Subpanel (230 volt Convertable) available from your Converting from 115 volts to 230 volts changes the voltage supplied HOT SPRING dealer. to the heater from 115-volts to 230 volts. The jet pump will continue to operate at 115 volts. - Page 12 Watkins Manufacturing Corporation (“Watkins”) warrants from the date of installation to Warranty Performance the original consumer purchaser (“you”) the following when your Hot Spring® Highlife® Collection spa is purchased from an authorized dealer/service provider (“dealer”). Year Shell Surface Warranty Watkins warrants the acrylic surface material of your Hot Spring Highlife Collection spa to not leak and be free from defects in materials and workmanship for seven years.