Table of Contents
Advertisement
Quick Links
"AR" SERIES BRONZE PUMPS
AR204-L
3/4 HP
Sta-Rite Pool/Spa Group
293 Wright Street, Delavan, WI 53115
International: 262-728-5551, FAX: 262-728-7550
www.starite.com
Union City, TN • Delavan, WI • Mississauga, Ont. • Murrieta, CA
© 2005, Sta-Rite Industries
WITH INTEGRAL TRAP
SELF-PRIMING
O
W
N
E
R '
INSTALLATION, OPERATION & PARTS
MODELS
AR205-L
1 HP
S
M
A
N
U
AR206-L
AR207-L
1-1/2 HP
A
L
AR208-L
2 HP
2-1/2 HP
Furnish this manual to the end user of
this pump; its use will reduce service
calls and chance of injury and will
lengthen pump life.
S512 (Rev. 5/2/05)
Advertisement
Table of Contents
Related Manuals for STA-RITE AR204-L 3/4 HP
Summary of Contents for STA-RITE AR204-L 3/4 HP
- Page 1 Sta-Rite Pool/Spa Group 293 Wright Street, Delavan, WI 53115 International: 262-728-5551, FAX: 262-728-7550 www.starite.com Union City, TN • Delavan, WI • Mississauga, Ont. • Murrieta, CA S512 (Rev. 5/2/05) © 2005, Sta-Rite Industries...
-
Page 2: Important Safety Instructions
• Release all air in system before testing. ignored. • Tighten Sta-Rite trap lids to 30 ft. lbs. (4.1 kg-cm) warns about hazards that will or can cause torque for testing. minor personal injury or property damage if ignored. -
Page 3: Installation
INSTALLATION Only qualified, licensed personnel should install pump and wiring. Pump Mount Must Be located away from corrosive or flammable liquids. Have enough ventilation to maintain air temperature at less than the maxi- mum ambient temperature rating (Max. Amb.) listed on the motor model plate. -
Page 4: Testing And Certification
Suction Outlets Per Pump (Figure 1, Page 4) Provide at least two hydraulically balanced main drains, with covers, as suction outlets for each circulating pump suction line. The centers of the main drains (suction outlets) on any one suction line must be at least three feet apart. The system must be built so that it cannot operate with the pump drawing water from only one main drain (that is, there must be at least two main drains connected to the pump whenever it is running –... - Page 5 Piping Use at least 2” pipe with 6” trap. Increase size if a long run is needed. To avoid strains on the pump, support both suction and discharge pipes inde- pendently. Place these supports near the pump. To avoid a strain left by a gap at the last connection, start all piping at the pump and run pipe away from the pump.
-
Page 6: Operation
Grounding/Bonding BONDING Install, ground, bond and wire motor according to local or National Electrical Code requirements. Permanently ground motor. Use green grounding terminal provided under motor canopy or access plate (See Figure 2); use size and type wire required GREEN by code. -
Page 7: Priming Pump
Priming Pump 230 Volt to 115 Volt Conversion. Move plug to change voltage. Ground Release all pressure from filter, pump and piping system; see the filter owner’s Screw 230 V 115 V manual. In a flooded suction system (water source higher than pump), pump will prime itself when suction and discharge valves are opened. -
Page 8: Pump Service
Startup for Winterized Equipment 1. Remove any temporary weather protection placed around system for shut- down. 2. Follow filter manufacturer’s instructions for reactivation of the filter. 3. Inspect all electrical wiring for damage or deterioration over the shutdown period. Have a qualified serviceman repair wiring as needed. 4. - Page 9 8. Unscrew impeller from shaft (turn counterclockwise when facing it). 9. Remove seal plate from motor. 10. Using two screwdrivers, pry rotating seal half off of shaft (See Figure 5A). 11. Place seal plate face down on flat surface and tap out ceramic seat (See Figure 5B).
- Page 10 CENTRIFUGAL POOL PUMPS 3378 0299 Part AR204-L AR205-L AR206-L AR207-L AR208-L Description Qty. 3/4 HP 1 HP 1-1/2 HP 2 HP 2-1/2 HP Motor, 3/4 HP, 115/230V, 60 Hz. AE100DLL – – – – Motor, 1 HP, 115/230V, 60 Hz. –...
-
Page 11: Troubleshooting Guide
TROUBLESHOOTING 2. Clogged Pipe/Trap/Impeller, Worn Impeller: GUIDE a. Make sure suction trap is not clogged; if it is, clean trap and strainer. Hazardous pressure. Read and understand safety and operating instructions in this manual before b. Make sure impeller is not clogged (follow instruc- doing any work on pump! tions under “Remove Old Seal”, Page 8;... - Page 12 • Complete a warranty registration at www.staritepool.com by clicking on “Register Products” and selecting Sta-Rite Pool OR • Complete bottom portion completely and mail within 10 days of installation to Sta-Rite, Attn.: Pool Warranty Dept., 293 Wright St., Delavan , WI 53115 Warranty Registration Card ■...