Power Electronics V2 Series User Manual
  1. Manuals
  2. Brands
  3. Power Electronics Manuals
  4. Controller
  5. V2 Series
  6. User manual
Power Electronics V2 Series User Manual

Power Electronics V2 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SOFTSTARTER
U s e r ' s M a n u a l

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V2 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Power Electronics V2 Series

Summary of Contents for Power Electronics V2 Series

  • Page 1 SOFTSTARTER U s e r ' s M a n u a l...
  • Page 2 ELECTRONICS SOFT-STARTER User’s Manual V2MT01II Rev. I POWER ELECTRONICS ESPAÑA C/ Leonardo da Vinci, 24 - 26 46980 · PARQUE TECNOLÓGICO PATERNA · VALENCIA · ESPAÑA Tel. +34 96 136 65 57 · Fax. +34 96 131 82 01 Atención al Cliente: 902 40 20 70...
  • Page 3 2 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 4 V2 soft-starters are carefully tested and perfectly packed before leaving the factory. • In case of transport damage, notify it to transport agency and to POWER ELECTRONICS (+34 96 136 65 57), not later than 24hrs from delivery date. UNPACKING •...
  • Page 5 Add new dimensions for 60 and 75A (IP54) Change DT0048D (Page 11). March 2003 IP54 new range release. October 2002 Jumper 7: Default value Freewheel Stop. July 2002 PCB Change. 00016B. Modify the jumper 9. 4 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 6: Table Of Contents

    1.6. Control wiring. 1.7. Checks before Commissioning. ELECTRICAL SPECIFICATIONS..................DIMENSIONS AND STANDARD RATINGS................ CONTROL INPUTS......................4.1. Control terminals. 4.2. Terminal descriptions. LED INDICATIONS......................POWER PCB JUMPER CONFIGURATION................ POTENTIOMETER COMMISSIONING................APPLICATIONS........................DECLARATION OF CONFORMITY CE................POWER ELECTRONICS User’s Manual V2 V2MT01II | 5...

  • Page 7: Mounting And Wiring

    S obr etemperatura Sobretemperatura Sobretemperatura Übertemperature Übertemperature Übertemperature General fault General fault General fault Fallo gener al Fallo general Fallo general Fehl er Fehler Fehler 150mm 30mm DT0055 Fig. 1: Vertical mounting. 6 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 8: Power Loss Dissipation

    We have a V2017 working at 30ºC ambient temperature. We want the air inside the cabinet less than 40ºC. POWER ELECTRONICS User’s Manual V2 V2MT01II | 7...

  • Page 9: Power Wiring

    It is absolutely necessary that the installer guaranties the correct observance of the law and the regulations that are in force in those countries or areas where this device is going to be installed. 8 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 10: Control Wiring

    Wiring options with push buttons or selector (switch) according to Selection 4.2. DIGITAL OUTPUTS FAULT INSTANT RELAY RELAY DIGITAL INPUTS 8 9 10 11 12 230Vac DT0038E Fig. 3: V2 Control Wiring. POWER ELECTRONICS User’s Manual V2 V2MT01II | 9...

  • Page 11: Checks Before Commissioning

    U, V, W. Confirm the mains supply is within V2 specifications and motor nameplate matches to V2 rated nameplate. 4. Check control wiring and ensure the installation is electrically safe and it is safe to run the motor. 10 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 12: Electrical Specifications

    · Instantaneous: Its position changes when starting and stopping LED’S INDICATIONS LED 1 Run LED 2 Ready LED 3 Overload warning / Underload fault LED 4 Overload Fault LED 5 Over temperature LED 6 General fault POWER ELECTRONICS User’s Manual V2 V2MT01II | 11...

  • Page 13: Dimensions And Standard Ratings

    18.5 IP54 V2060B* 410x157x132 IP54 V2075B* 410x157x132 * All types signed with “*” do have an integrated BYPASS function. The Motor protection is operating all the time. Table 1: V2 standard ratings. 12 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 14: Control Inputs

    Fault: It switches in case of any fault condition. Instantaneous: It switches when starting/ stopping FAULT RELAY INSTANT RELAY DT0048F Fig. 6: Output relay. NOTE: Maximum current per conta ct 5A at 230V. POWER ELECTRONICS User’s Manual V2 V2MT01II | 13...
  • Page 15 Start pul pushbutton configuration. For variable load applications (different material mixing, etc.), where sometimes a higher torque is required, torque pulse pushbutton inputs are provided. Start Pu DT0052C Fig. 10: Start pulse configuration. 14 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 16: Led Indications

    It is steadily on after acceleration ramp when running at nominal current. LED 3 OVERLOAD WARNING & UNDERLOAD FAULT Blinking light: UNDERLOAD FAULT Description Motor Underload. Possible Cause Motor working with no load. POWER ELECTRONICS User’s Manual V2 V2MT01II | 15...
  • Page 17 Phase or PCB fault. Possible Cause Phase loss. Phase unbalance. Thyristor fau Action Check supply, all cables, mo r. If the problem persi sts, call to POWER ELECTRONICS or an authorized distributor. 16 | POWER ELECTRONICS User’s Manual V2 V2MT01II...

  • Page 18: Power Pcb Jumper Configuration

    Position 2: 230V (to introduce 6 jumpers according to drawing). Add or remove 6 jumpers (2 per phase) according to input voltage at the soft starter input. Make sure this value is related to rated (Nameplate) motor voltage. POWER ELECTRONICS User’s Manual V2 V2MT01II | 17...
  • Page 19 Default Position 1: 50Hz unction Set the mains frequency. djust Where the mains frequency is known as 50Hz, leave as default. Where the mains frequency is 60Hz set jumper to Position 2. 18 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 20 Position 1 (default): Underload protection is disabled. Position 2: Underload protection is enabled. Position 1: Desable u/l protection Position 2: Enable u/l protection DT0057D Fig. 16: JP9: Underload cu rrent selection jumper. POWER ELECTRONICS User’s Manual V2 V2MT01II | 19...

  • Page 21: Potentiometer Commissioning

    40% and 50%. End of Start of deceleration acceleration ramp ramp CURR NT 100% End of deceleration Start of ramp acceleration ramp Initial torque Acceleration Deceleration ramp ramp Time DT0042B Fig.18: Initial torque. 20 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 22 OVERLOAD. Adjust If you need a fast response under overload conditions, please select Min. If you need a slow response, then select Max. For normal operation, leave this value as medium setting. POWER ELECTRONICS User’s Manual V2 V2MT01II | 21...
  • Page 23 This parameter sets the maximum operation time under underload conditions before tripping. See overload POT5. djust Depends on the application, but should be set to trip as soon as a condition occurs. pplications Pumps, fans. 22 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 24 O/L CURVE UNDERLOAD U/L TIME I. LIMIT INITIAL. STARTM. HOCHLAUF RÜCKLAUF ÜBERLAST ÜBERLASTKURVE UNTERLAST UNTERLASTZEIT STROMBEGRENZ 15S. 0.8xIn 1.2xIn 0.2xIn 0.6xIn MIN MAX 1xIn 5xIn DT0041D Fig. 20: Hard start potentiometer configuration. POWER ELECTRONICS User’s Manual V2 V2MT01II | 23...

  • Page 25: Applications

    MIN MAX 1xIn 5xIn DT0041D Fig. 21: Hard start potentiometer configuration. CONTROL TERMINALS DIGITAL OUTPUTS FAULT INSTANT RELAY RELAY DIGITAL INPUTS 8 9 10 11 12 230Vac DT0068C Fig. 22: V2 Control Terminals. 24 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 26 1xIn 5xIn DT0077A Fig. 24: Fans and Pumps potentiometer configuration. NOTE: For pumping systems please check fig. 14 and 16 to configure Jumpers 7 and 9 as deceleration ramp and underload activation. POWER ELECTRONICS User’s Manual V2 V2MT01II | 25...

  • Page 27: Declaration Of Conformity Ce

    UNE-EN 50081-2:94 Electromagnetic Compatibility. Generic emission standard. Part 2 : Industrial environment. Manufacturer authorized signature: Name: David Salvo Title: Executive Manager Date of issue: 1. September 2002 Place of issue: Valencia, Spain 26 | POWER ELECTRONICS User’s Manual V2 V2MT01II...
  • Page 28 POWER ELECTRONICS ESPAÑA: C/ Leonardo da Vinci, 24-26 · 46980 · Parque Tecnológico · PATERNA · VALENCIA · ESPAÑA · Tel. 902 40 20 70 · Fax. +34 96 131 82 01 www.power-electronics.com POWER ELECTRONICS DEUTSCHLAND Gmbh: Conradtystrasse, 41 · 90441 · Nürnberg · Tel +49 911 99 43 990 · Fax. +49 911 99 43 999...

This manual is also suitable for:

V2mt01ii

Table of Contents