Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for nvent Raychem NRG-Temp
Summary of Contents for nvent Raychem NRG-Temp
- Page 1 NRG-Temp Version 4.2...
- Page 2 70.5 70.5 nVent Figure 1 Figure 2 2 | nVent.com...
-
Page 3: Table Of Contents
Standby Standby • • • • • • • • • • • • • • • • EcoOffice nVent.com | 3 • • • • • • • • • • • • • • • • • •... - Page 4 7.2.3 User Menu C: Running time 7.2.4 User Menu D: Adjustable switching hysteresis 7.2.5 User Menu E: Delayed Start-Up 7.2.6 User Menu F: Frost protection for OFF Programme 7.2.7 User Menu G: Proportional regulation 7.2.8 User Menu H: Set back temperature offset 4 | nVent.com...
- Page 5 Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. nVent.com | 5...
-
Page 6: Description
DESCRIPTION EcoHome The nVent RAYCHEM NRG-Temp thermostat is a smart thermostat designed for electrical underfloor heating. It is designed to give you the best possible • • • • • • comfort with the least energy consumption. The NRG- Temp is equipped with an ambient sensor and a floor... - Page 7 As soon as there is a new timer event, (Only in EcoH the temperature will return to or EcoO the Reduced or to the Comfort programme) temperature depending on the time schedule of the Economic programme. Table 2 nVent.com | 7...
-
Page 8: Mounting And Installation
Note: The NRG-Temp can also be mounted on a wall with a wall box. Assembly frame and front of thermostat can be removed by pushing gently with a screw driver on the two fasteners located on each side of the thermostat (see Figure 4). 8 | nVent.com... -
Page 9: Mounting The Floor Sensor
Do not position the floor sensor tip closer than 3 cm to the heating cable. 500 mm Figure 5 Remark: The floor sensor cable can be extended to 100 m with a separate standard installation cable 2 x 1.5 mm (230VAC). nVent.com | 9... -
Page 10: Connection Of The Thermostat To The Power Supply
N N N K1 A2 K1: contacter with integrated HEAT suppression device N N N Do not use contactor without interference filter. K1: contacter with integrated HEAT suppression device Figure 7 Do not use contactor without interference filter. 10 | nVent.com... -
Page 11: Product Specific Information
NRG-Temp thermostat working in floor sensor mode. Be aware that the floor sensor must be installed and activated for any installation with T2QuickNet. 3.4.2 NRG-TEMP WITH THE NVENT RAYCHEM T2RED (T2REFLECTA) SELF-REGULATING CABLE Self-regulating heating cables have an inrush current at start up. -
Page 12: Getting Started
• • • • • • • • • • • • • • • • • • • 12 | nVent.com • • • • • • • • • • • • • • • • • •... -
Page 13: Navigation
• • • • • • • • • • • • • • • • • • • • • nVent.com | 13 • • • • • • • • • • • • • • • •... - Page 14 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 14 | nVent.com...
-
Page 15: Functions
• • • • • • • • • • • • • • • • • Standby Standby Standby Standby nVent.com | 15 • • • • • • • • • • • • • • • •... -
Page 16: In Economic Programmes (Ecoh/Ecoo)
• • EcoOffice EcoOffice • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 16 | nVent.com EcoOffice... -
Page 17: Programme 1: Comfort (Co)
• EcoOffice Standby • • • • • • • • • • • • • • • • nVent.com | 17 Standby • • • • • • • • • • • • • • • • •... -
Page 18: Programme 3: Economic Office (Ecoo)
• • • • • • • • • • • • • • show the following screen for 3 seconds: • • • • • • • • • • • • • • • • 18 | nVent.com... -
Page 19: Programming
• • • • • • • • • • • • • • • • • Figure 19 nVent.com | 19 • • • • • • • • • • • • • • • • • •... - Page 20 2: Service read out • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 20 | nVent.com EcoOffice EcoOffice...
- Page 21 * Only available if the external floor sensor is installed • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • EcoOffice EcoOffice nVent.com | 21...
- Page 22 • • • • • • • • • • • • • • • • • • • • • • room sensor value • • • • • • • • • • Standby Standby 22 | nVent.com...
- Page 23 (away from direct sunlight). Once the temperature is stable, read the temperature on the thermometer and fill in this temperature in this menu by using EcoHome EcoHome nVent.com | 23 • • • • • •...
- Page 24 • • • Standby • • • • • • • • • • • • • • • • Standby • • • • • • • • • • • • • • • • 24 | nVent.com...
- Page 25 • • • • • • • • • • • • • • • • nVent.com | 25 • • • • • • • • • • • • • • • •...
- Page 26 ON again, is the hysteresis. This function defines the temperature range between the switching ON and OFF of the heating in floor sensing mode. Possible values: 0.2 to 2.0°C Factory set value: 0.5°C 26 | nVent.com...
- Page 27 This Setback Temperature OFFSET is neglected when the external set back signal is not present or the pilot wire is not connected. Possible values: -1.0 to -7.0°C Factory set value: -3.5°C nVent.com | 27...
- Page 28 • • • • • • • • • • • • • • EcoOffice EcoOffice EcoOffice Management System): 28 | nVent.com • • • • • • • • • • • • • • • • • •...
- Page 29 • • • • • • • • • • • • • • • • power (on/off) switch, on the front of the thermostat. All set values will return to factory defaults. The thermostat will re-boot. nVent.com | 29...
- Page 30 - Comfort (Fixed Programme) - EcoHome (Fully Customizable) - EcoOffice (Fully Customizable) - OFF Back-up for set values In non-volatile memory Back-up for time and date 24 hours Optional external set back feature 6 external set-back signals Table 8 30 | nVent.com...
- Page 31 12 APPROVALS AND DECLARATIONS nVent.com | 31...
- Page 32 +47 66 81 79 90 salesno@nvent.com nVent.com ©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.
Need help?
Do you have a question about the Raychem NRG-Temp and is the answer not in the manual?
Questions and answers