Sensor - FUTABA T16IZ Manual

Sensor

This screen registers the telemetry sensors used
with the transmitter. When only one of a certain
type of sensor is used, this setting is unnecessary
and the sensor can be used by simply connecting it
to the S.BUS2 port of the transmitter.
When using 2 or more of the same kind of sensor,
they must be registered here.
● Tap the [Sensor] button in the Linkage menu
to call the setup screen shown below.
Slot Number
Sensor ID : Multiple usage of sensors
of the same type requires an ID
be input. Tapping this will allow
for manual input, but see the next
page about how to perform auto-
registration via sensor registration.
● As shown in the table below, an altimeter requires 3 contiguous slots and a GPS sensor
requires 8 contiguous slots. The GPS (SBS-01/02G) start slots are 8, 16, and 24.
＜ Assignable slot ＞
The required number
Sensor
of slots
TEMP (SBS-01T/TE) 1 slot
RPM (SBS-01RM/RO/RB) 1 slot
Airspeed (SBS-01TAS) 1 slot
Voltage (SBS-01V) 2 slots
Altitude (SBS-01/02A) 3 slots
Current (SBS-01C) 3 slots
S.BUS Servo sennsor（SBS-
6 slots
01S)
GPS(SBS-01/02G) 8 slots
EM-100 (O.S. ENGINE) 12 slots
TEMP125-F1713 1 slot
VARIO-F1712 2 slots
VARIO-F1672 2 slots
CURR-F1678 3 slots
GPS-F1675 8 slots
Kontronik ESC 8 slots
Castle TL0 8 slots
JetCat V10 14 slots
PowerBox 16 slots
Various telemetry sensors setting
Registered sensor
Tap the slot to display
sensors which can be used
for the start slot. Tap to
register the sensor.
*Altimeter, GPS, and other sensors that display a large amount of data require multiple slots.
*Depending on the type of sensor, the slot numbers that can be allocated may be limited.
The number which can be used as a start slot
1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,
2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9
1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9
1 , 2 , 8 , 9 , 1 0 , 1 6 , 1 7 , 1 8 ,
1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,
2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,
2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9
1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 5 , 1 6 , 1 7 ,
91
[Whatisaslot?]
Servos are classified by CH, but sensors are
classifiedinunitscalled"slot".Thereareslotsfrom
No.1toNo.31.
Altitude sensors, GPS sensors and other data
sensorunitsmayusemultipleslots.
When using a sensor which uses two or more
slots,therequirednumberofslotsisautomatically
assignedbysettingupastartslot.
When2ormoreofthesamekindofsensorare
used,thesensorsthemselvesmustallocateunused
slotsandmemorizethatslot.
This is what displays when no
s e n s o r i s r e g i s t e r e d i n a s l o t .
Tapping the slot and selecting
"-----------" will erase whatever was
registered there, freeing up the
slot.
1-31
1-31
1-31
2 4 , 2 5 , 2 6
8 , 1 6 , 2 4
8 , 1 6
1-31
8 , 1 6 , 2 4
8 , 1 6 , 2 4
8 , 1 6 , 2 4
1 8
8 , 1 6
→ GO to TABLE OF CONTENTS
Selling area
Global
Europe