Related Manuals for turck LI-Q25L E Series
Summary of Contents for turck LI-Q25L E Series
- Page 1 Your Global Automation Partner LI-Q25L…E Linear Position Sensors with Analog Output Instructions for Use...
-
Page 2: Table Of Contents
Reset the sensor to the inverted factory settings.............. 21 9.2.4 Activating the teach lock...................... 22 9.2.5 Deactivating teach lock....................... 22 10 Troubleshooting.......................... 23 11 Maintenance ............................. 24 V03.00 | 2022/08 | 2 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 3 12 Repair .............................. 24 12.1 Returning devices ...................... 24 13 Disposal.............................. 24 14 Technical data........................... 25 15 Turck subsidiaries — contact information.................. 26 V03.00 | 2022/08 | 3 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 4 Contents V03.00 | 2022/08 | 4 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 5: About These Instructions
If you have any suggestions for improving the design or if some information is missing in the document, please send your suggestions to techdoc@turck.com. V03.00 | 2022/08 | 5 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 6: Notes On The Product
Linear position sensor (without positioning element) Optional: Positioning element and mounting element Turck service Turck supports you with your projects, from initial analysis to the commissioning of your applic- ation. The Turck product database under www.turck.com contains software tools for program- ming, configuration or commissioning, data sheets and CAD files in numerous export formats. -
Page 7: For Your Safety
The product is designed according to state-of-the-art technology. However, residual risks still exist. Observe the following warnings and safety notices to prevent damage to persons and property. Turck accepts no liability for damage caused by failure to observe these warning and safety notices. -
Page 8: Product Description
Fig. 1: Dimensions in mm – L = 29 mm + measuring length + 29 mm 45.7 38.6 33.8 25.2 Fig. 2: Dimensions – device height V03.00 | 2022/08 | 8 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 9: Properties And Features
24 mA or 11 V as a fault signal. This error can therefore be evaluated directly via the higher-level control. V03.00 | 2022/08 | 9 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 10: Technical Accessories
ø 5,2 21,5 (4x) distance of up to 5 mm or a misalignment tolerance of up to 4 mm reference 26,3 point 35,5 V03.00 | 2022/08 | 10 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 11 20,7 40,4 M1-Q25L 6901045 Mounting foot for LI-Q25L linear position sensors; material: aluminum; 2 pcs. per bag 10,6 31,2 V03.00 | 2022/08 | 11 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 12 Sliding block with M4 thread for the backside profile of the LI-Q25L linear position sensor; material: galvanized metal; 10 pcs. per bag 11,5 V03.00 | 2022/08 | 12 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 13 18° 19,2 RBVA-M5 6901059 Angle joint for guided position- ing element; material: stainless steel 18° 19,2 V03.00 | 2022/08 | 13 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 14: Connection Accessories
2 m, jacket material: PUR, black; cULus approval; M12 x 1 other cable lengths and versions ø 15 available, see www.turck.com 45.4 V03.00 | 2022/08 | 14 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 15: Installing
Mounting element Recommended tightening torque M1-Q25L 3 Nm M2-Q25L 3 Nm MN-M4-Q25L 2.2 Nm Sensor type Recommended number of fixings LI100…LI500 LI600…LI1000 LI1250…LI1500 LI1750…LI2000 V03.00 | 2022/08 | 15 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 16: Mounting Free Positioning Elements
LED 1 lights up green when the positioning element is in the measuring range. Fig. 5: Center the free positioning element V03.00 | 2022/08 | 16 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 17: Connection
5 GY 4 BK ext. teach Fig. 6: M12 male connector — pin assignment Fig. 7: M12 male connector — wiring diagram V03.00 | 2022/08 | 17 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 18: Commissioning
Commissioning Commissioning After connecting and switching on the power supply, the device is automatically ready for operation. V03.00 | 2022/08 | 18 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 19: Operation
Yellow flashing Positioning element not in detection range Positioning element outside the set measuring range LED 2 Green Power supply error-free V03.00 | 2022/08 | 19 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 20: Setting
LED 2 initially flashes green for 2 s, then lights up green continuously for 8 s and flashes green again (after a total of 10 s). The sensor is reset to its inverted factory setting. V03.00 | 2022/08 | 20 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 21: Setting The Measuring Range
LED 2 initially flashes green for 2 s, then lights up green continuously for 8 s and flashes green again (after a total of 10 s). The sensor is reset to the inverted factory setting. V03.00 | 2022/08 | 21 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 22 LED 2 lights up green continuously for 30 s (teach lock is still activated) and after 30 s flashes green at a higher frequency. The teach lock function of the sensor is deactivated. V03.00 | 2022/08 | 22 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
-
Page 23: Troubleshooting
If there are no faults, there is a device malfunction. In this case, decommission the device and replace it with a new device of the same type. V03.00 | 2022/08 | 23 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 24: Maintenance
Observe our return acceptance conditions when returning the device to Turck. 12.1 Returning devices Returns to Turck can only be accepted if the device has been equipped with a Decontamination declaration enclosed. The decontamination declaration can be downloaded from https://www.turck.de/en/retoure-service-6079.php and must be completely filled in, and affixed securely and weather-proof to the outside of the packaging. -
Page 25: Technical Data
138 years acc. to SN 29500 (Ed. 99) 40 °C Packed quantity Operating voltage indication LED: green Measuring range display Multifunction LED: green, yellow, yellow flashing V03.00 | 2022/08 | 25 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... -
Page 26: Turck Subsidiaries - Contact Information
Turck Banner Malaysia Sdn Bhd Unit A-23A-08, Tower A, Pinnacle Petaling Jaya, Jalan Utara C, 46200 Petaling Jaya Selangor www.turckbanner.my V03.00 | 2022/08 | 26 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com... - Page 27 Árpád fejedelem útja 26-28., Óbuda Gate, 2. em., H-1023 Budapest www.turck.hu Turck Inc. 3000 Campus Drive, USA-MN 55441 Minneapolis www.turck.us V03.00 | 2022/08 | 27 Hans Turck GmbH & Co. KG | T +49 208 4952-0 | more@turck.com | www.turck.com...
- Page 28 Over 30 subsidiaries and 60 representations worldwide! 100003779 | 2022/08 100003779 www.turck.com...