Related Manuals for Horizon Hobby E-flite UMX NIGHT VAPOR RTF
Summary of Contents for Horizon Hobby E-flite UMX NIGHT VAPOR RTF
- Page 1 ® Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,...
-
Page 3: Table Of Contents
Box Contents RTF Only Table of Contents Specifications ..............3 Center of Gravity ............... 8 Preflight Checklist ............. 4 Trimming the Aircraft ............9 Charging Warnings............4 Flying ................9 Charge the Flight Battery ..........4 Post Flight Checklist ............ 10 Install the Transmitter Batteries (RTF) ........ -
Page 4: Preflight Checklist
Preflight Checklist Find a safe and open area. Perform control direction test. Charge the flight battery. Plan flight for flying field conditions. Assemble the aircraft. Set a flight timer for 7 minutes. Install the transmitter batteries. Have fun! Install the flight battery. Charging Warnings WARNING: Failure to exercise caution while using this •... -
Page 5: Install The Transmitter Batteries (Rtf)
Install the Transmitter Batteries (RTF) 1. Remove the battery cover from the back of the transmitter. 2. Install four included AA batteries (noting proper polarity). 3. Reinstall the battery cover. Low Battery Alarm When the battery voltage drops too low, an alarm sounds and the LED flashes. -
Page 6: Bnf Transmitter Setup
BNF Transmitter Setup IMPORTANT: The installed receiver has been Computerized Transmitter Setup programmed for operation specifically in this aircraft. Start all transmitter programming with a blank ACRO To operate the various features of this aircraft, follow the model (perform a model reset), then name the model. table to setup your computer transmitter. -
Page 7: Rtf And Bnf Binding Procedures
RTF and BNF Binding Procedures CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. -
Page 8: Control Direction Test
Control Direction Test CAUTION: Always keep hands away from the Stick Movement Control Surface Reaction propeller. When armed, the motor will turn the propeller in response to any throttle movement. Test the controls prior to the first flight to ensure none of the servos, linkages or parts were damaged during shipping and handling and the controls function in the correct directions. -
Page 9: Trimming The Aircraft
Trimming the Aircraft Adjusting Trim in Flight Direction of Drift Button to Correct Familiarize yourself with your transmitter’s controls and the aircraft’s response before flying by performing the recommended Control Direction Test. Press the trim buttons on your transmitter to adjust how the aircraft flies. If the aircraft’s nose drifts while the sticks are at neutral (centered) and the throttle is at 50%, press the trim buttons: •... -
Page 10: Post Flight Checklist
Post Flight Checklist Disconnect the flight battery from the ESC. Repair or replace all damaged parts. Power OFF the transmitter. Store the flight battery apart from the aircraft and monitor the battery charge. Remove the flight battery from the aircraft. Make note of the flight conditions and flight plan results, Recharge the flight battery. - Page 11 Removing/Replacing the Landing Gear To remove the landing gear: 1. Gently grasp the landing gear base and pull the landing gear assembly out of the mount. TIP: It may be difficult to remove the landing gear the first time. 2. Thread the new metal gear strut into the plastic insert. 3.
-
Page 12: Troubleshooting
Troubleshooting Problem Possible Cause Solution Reset controls with throttle stick and throttle Aircraft will not Throttle stick and/or throttle trim is too high trim at lowest setting respond to throttle but responds to Ensure the plug for the motor is properly Motor is disconnected from receiver other controls installed... -
Page 13: Parts List
Product, (iv) attempted as the purchaser or user are not prepared to accept the liability service by anyone other than a Horizon Hobby authorized associated with the use of the Product, purchaser is advised to... -
Page 14: Warranty And Service Contact Information
United States 2904 Research Rd (Product Technical Assistance) of America 877-504-0233 Champaign, IL 61822 websales@horizonhobby.com Sales 800-338-4639 Horizon Technischer Service service@horizonhobby.eu Hanskampring 9 European Union D 22885 Barsbüttel, Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100 Germany Night Vapor... -
Page 15: Fcc Information
EU Manufacturer of Record: EU Compliance Statement: Horizon Hobby, LLC E-Flite Night Vapor RTF/BNF (EFLU1300/ EFLU1350); Hereby, Horizon Hobby, LLC 2904 Research Road declares that the device is in compliance Champaign, IL 61822 USA with the following: EU Radio Equipment Directive 2014/53/... - Page 16 © 2020 Horizon Hobby, LLC. E-flite,Vapor, Bind-N-Fly, BNF, the Bind-N-Fly logo, SAFE, the SAFE logo, AS3X, ModelMatch, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the E-flite UMX NIGHT VAPOR RTF and is the answer not in the manual?
Questions and answers
How do I replace the main spar of the night vapor