Summary of Contents for Horizon Hobby E-flite UMX Turbo Timber Evolution
Page 1
UMX Turbo Timber Evolution Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information. Scannen Sie den QR-Code und wählen Sie auf der Produktseite die Quicklinks Handbücher und Unterstützung, um die aktuellsten Instruction Manual Informationen zu Handbücher.
Page 2
WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.
Low Voltage Cutoff (LVC) When a Li-Po battery is discharged below 3V per cell, it about half capacity before storage. Make sure the battery will not hold a charge. The aircraft’s ESC protects the flight charge does not fall below 3V per cell. Failure to unplug a battery from over-discharge using Low Voltage Cutoff (LVC).
Smart Technology Telemetry This aircraft includes Spektrum Smart Technology in the 3. Power on the aircraft. receiver, which can provide telemetry information like bat- 4. The Smart logo appears under the battery logo on the tery voltage. To take advantage of Smart Technology, you home page.
ESC/Receiver Arming and Battery Installation CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. Arming the ESC/receiver also occurs after binding as previously described, but subsequent connection of a flight battery requires the following steps.
Control Direction Test Switch on the transmitter, enable throttle cut and connect Transmitter Control Surface Response the battery. Use the transmitter to operate the aileron, Command elevator and rudder controls. View the aircraft from the rear when checking the control directions. Elevators 1.
Optional Float Set Installation Landing Gear Removal 1. Carefully invert the aircraft. 2. Remove the 4 screws and 2 plates securing the land- ing gear. 3. Remove the other 4 screws and 2 plates for the rear float mount. Save all screws and plates for the float installation.
Flying Tips and Repairs WARNING: Always engage throttle cut before Landing approaching the aircraft. Always land into the wind. During the flare, keep the wings level and the aircraft pointed into the wind. Slowly Range Check the Radio System lower the throttle while easing back on the elevator to Range check the radio system with the aircraft.
Power Components Service Disassembly CAUTION: DO NOT handle the propeller while the flight battery is connected to the ESC. Personal injury could result. Propeller 1. Gently grasp the spinner ( ) taking care not to crush it, and pull while rocking the spinner back and forth to break the adhesive.
AS3X System Trouble Shooting Guide ® Problem Possible Cause Solution Control surfaces may not have been Center control surfaces mechanically by Control surfaces not at mechanically centered from factory adjusting the U-bends on control linkages neutral position when Aircraft was moved after the flight battery was transmitter controls are Disconnect and reconnect the flight battery connected and before sensors...
Page 12
Troubleshooting Guide Problem Possible Cause Solution Less than a 5-second wait between first Leaving transmitter on, disconnect and recon- powering on transmitter and connecting flight nect flight battery to aircraft battery to aircraft Select correct model memory on transmitter Aircraft bound to different model memory and disconnect and reconnect flight battery to (ModelMatch radios only)
Product, (iv) attempted ser- right to inspect any and all Product(s) involved in a warranty vice by anyone other than a Horizon Hobby authorized service claim. Service or replacement decisions are at the sole discre- center, (v) Product not purchased from an authorized Horizon tion of Horizon.
Horizon Product Support United States 2904 Research Rd (Product Technical Assistance) of America 877-504-0233 Champaign, Illinois, 61822 USA websales@horizonhobby.com Sales 800-338-4639 Horizon Technischer Service service@horizonhobby.eu Hanskampring 9 European Union D 22885 Barsbüttel, Germany Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100...
EU Compliance Statement: EU Manufacturer of Record: EFL UMX Turbo Timber Evolution BNF Horizon Hobby, LLC Basic (EFLU8950): Hereby, Horizon Hobby, 2904 Research Road Champaign, IL 61822 USA LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU, RoHS...
Page 17
E-flite, Plug-N-Play, Bind-N-Fly, BNF, the BNF logo, DSM, DSM2, DSMX, Spektrum AirWare, EC3, IC3, AS3X, SAFE, the SAFE logo, ModelMatch, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Need help?
Do you have a question about the E-flite UMX Turbo Timber Evolution and is the answer not in the manual?
Questions and answers