Advertisement
Quick Links
Operation Manual
Polishing Machine
62422, 62426
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 62422
Summary of Contents for WilTec 62422
- Page 1 Operation Manual Polishing Machine 62422, 62426 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Remove all wrenches before switching on the device. An adjustment wrench or wrench that is still attached to a moving part can cause injury. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 To remove the guard, loosen the locking screw and turn the device until the two bumps are over the notches on the shaft. You can then remove the wheel guard. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 4 http://www.WilTec.de...
- Page 5 Shaft base Lateral handle The side handle is used to guide the device evenly and can be attached either to the right or left of the housing. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 30° will lead to a reduced bearing surface and might create notches due to attrition. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 6 http://www.WilTec.de...
- Page 7 Make sure that the new carbon brush is properly seated before you reattach the cover. Both carbon brushes should be replaced at the same time, even if only one brush is worn. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 7 http://www.WilTec.de...
- Page 8 Be careful when using detergents or solvents as they might damage the plastic parts of the tool. Therefore, refrain from using gasoline and carbon tetrachloride or detergents and solvents that are chlorinated or contain ammonia. © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 8 http://www.WilTec.de...
- Page 9 Handle (left piece) Nut M7 Label Spiral bevel gear Side handle Bearing 6201 Wrench Middle plate Wheel guard Armature Inner flange Gasket Plate Bearing 608 Flange nut © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 Explosionszeichnung © by WilTec Wildanger Technik GmbH Item 62422, 62426 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 11 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.