Advertisement
Quick Links
Operation Manual
Drywall Sander
61054
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61054
Summary of Contents for WilTec 61054
- Page 1 Operation Manual Drywall Sander 61054 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Technical specifications Voltage supply (V~) 230–240 Power (W) 1010 Frequency (Hz) Max. speed (rpm) 3200 Disc diameter (mm) Net weight (kg) © by WilTec Wildanger Technik GmbH Item 61054 Page 3 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
-
Page 4: On/Off Switch
There is a higher risk of electrical shock, when the body is earthed. Keep the machine away from rain or wet. The permeation of water into the power tool in- creases the risk of an electrical shock. © by WilTec Wildanger Technik GmbH Item 61054 Page 4 http://www.WilTec.de http://www.aoyue.eu... - Page 5 Service Have the power tool repaired only by qualified persons and only with the original replacement parts in order to ensure that the safety of the machine is maintained. © by WilTec Wildanger Technik GmbH Item 61054 Page 5 http://www.WilTec.de http://www.aoyue.eu...
-
Page 6: Installation
The grinding surface adhesive disc has a layer of cloth so it can quickly and easily be installed. The surface grinding sandpaper is pressed into the adhesive disc. Do not use the sander without a proper abrasive pad installed to prevent severe damage to the work. © by WilTec Wildanger Technik GmbH Item 61054 Page 6 http://www.WilTec.de... - Page 7 1500 rpm) and “6” being the fastest speed (approx. 3050 rpm). Use the higher speed settings for fast stock removal; use the lower speed to reduce removal rate for more precise control. © by WilTec Wildanger Technik GmbH Item 61054 Page 7 http://www.WilTec.de...
- Page 8 NOTE: Do not allow rotating abrasive pad to contact sharp protrusions. Contact with protrud- ing objects (nails, screws, electrical boxes, etc,), can severely damage the abrasive pad. © by WilTec Wildanger Technik GmbH Item 61054 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 50% full of dust, please clean up the dust timely. (5) When you finish the sanding, please let sanding pad still touch the working surface for seconds to let the dust suction be completed by the sander. © by WilTec Wildanger Technik GmbH Item 61054 Page 9 http://www.WilTec.de...
- Page 10 © by WilTec Wildanger Technik GmbH Item 61054 Page 10 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
-
Page 11: Disposal Regulations
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste. -
Page 12: Eg-Konformitätserklärung
It has been tested with the following harmonised standards: Il a été testé à partir des normes harmonisées suivantes : EN 60745-1 :2009/A11 :2010 EN 60745-2-3 :2011/A12 :2014 Bevollmächtigter für die Zusammenstellung der technischen Unterlagen: Bernd Wildanger, Geschäftsführer WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Deutschland Eschweiler, 14. Januar 2016...