Advertisement
Quick Links
Operation Manual
Drywall Sander for Ceilings and Walls
61055
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61055
Summary of Contents for WilTec 61055
- Page 1 Operation Manual Drywall Sander for Ceilings and Walls 61055 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 “power tool” is referring to a mains operated power tool (corded) and a battery-oper - ated power tool (not corded). Keep these safety instructions in a safe place! © by WilTec Wildanger Technik GmbH Item 61055 Page 3 http://www.WilTec.de...
- Page 4 Voltage supply (V) 220–240 ~ / 110 ~ Power (W) 710/750 Frequency (Hz) 50/60 Speed (rpm) 1000–2100 Disc diameter (mm) Net weight (kg) Protection class Protection degree IP20 © by WilTec Wildanger Technik GmbH Item 61055 Page 4 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
- Page 5 Illustrations ON/OFF switch Speed adjuster Foldable part Motor © by WilTec Wildanger Technik GmbH Item 61055 Page 5 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
- Page 6 Do not use an adapter plug together with earthed power tools. Non-ma - nipulated plugs and proper outlet connection reduce the risk of an electrical shock. © by WilTec Wildanger Technik GmbH Item 61055 Page 6 http://www.WilTec.de...
- Page 7 structions. Consider the working conditions and the task at hand. Using a power tool for a pur- pose other than its intended use can lead to dangerous situations. © by WilTec Wildanger Technik GmbH Item 61055 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 The surface grinding sandpaper pressed in the adhesive disc. Do not use the sander without a proper abrasive pad installed (to prevent severe damage to the work). © by WilTec Wildanger Technik GmbH Item 61055 Page 8 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
- Page 9 Use the higher speed settings for fast stock removal; use the lower speed setting to reduce re- moval rate for more precise control Angle grinding In order to do side grinding work, assemble with the delta pad. © by WilTec Wildanger Technik GmbH Item 61055 Page 9 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de...
- Page 10 Using a cross-tip screwdriver, unscrew the brush cover counter-clock- wise, remove the original carbon brush, put a new carbon brush to the brush holder and re-screw the brush cover. © by WilTec Wildanger Technik GmbH Item 61055 Page 10 http://www.WilTec.de...
- Page 11 Power tools produced by the company are subject to a strict quality inspection; yet, if there are failures, please contact the customer service department before every repair. © by WilTec Wildanger Technik GmbH Item 61055 Page 11 http://www.WilTec.de http://www.aoyue.eu...
- Page 12 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.
- Page 13 Il a été testé à partir des normes harmonisées suivantes : EN 60745-1 :2009/A11 :2010 EN 60745-2-4 :2009/A11 :2011 EN 60745-2-3 :2011/A13 :2015 Bevollmächtigter für die Zusammenstellung der technischen Unterlagen: Bernd Wildanger, Geschäftsführer WilTec Wildanger Technik GmbH Königsbenden 12 52249 Eschweiler Deutschland Eschweiler, 21. August 2017 __________________________ Bernd Wildanger Geschäftsführer...