Table of Contents
Advertisement
Available languages
Available languages
GB
1. About this document
– Please read carefully and keep in a
safe place.
– Under copyright.
Reproduction either in whole or in part
only with our consent.
– Subject to change in the interest of
technical progress.
Symbols
!
Hazard warning!
Reference to other information
...
in the document.
2. General safety precautions
Disconnect the power supply
!
before attempting any work
on the sensor.
• During installation, the electric power
cable being connected must not be
live. Therefore, switch off the power
first and use a voltage tester to make
sure the wiring is off-circuit.
• Installing the sensor involves work
on the mains power supply. This
work must therefore be carried out
professionally in accordance with
national wiring regulations and electri-
cal operating conditions.
• Only use genuine replacement parts
• Repairs may only be made by spe-
cialist workshops.
3. HF 360-2 KNX /
Hallway KNX
Proper use
– Sensor for ceiling mounting indoors.
– Connection to the KNX bus system.
The HF 360-2 KNX sensor also detects
movements through thin walls. This
makes it ideal for WC facilities with toilet
cubicles, changing rooms, stairwells,
multi-storey car parks and kitchens.
The detection zone of the sensor can be
precisely limited by ETS.
The Hallway KNX Sensor is a high-
frequency sensor with a perfect detection
zone for corridors. Reach can be adjust-
ed in both directions by ETS.
UP: concealed version
AP: surface-mounted version
Package contents
(Fig. 3.1, Fig. 3.4, Fig. 3.7, Fig. 3.10)
Product dimensions
(Fig. 3.2, Fig. 3.5, Fig. 3.8, Fig. 3.11)
Product components
(Fig. 3.3, Fig. 3.6, Fig. 3.9, Fig. 3.12)
A Surface-mounting adapter
B Load module
C Connecting terminal
D Programming button
E Sensor module
HF 360-2 KNX detection zone
(Fig. 3.13)
Hallway KNX detection zone
(Fig. 3.14)
- 12 -
Technical specifications
– HF 360-2 dimensions (H × W × D):
Surface-mounted installation:
103 × 103 × 60 mm
Surface-mounted installation:
123 × 123 × 57 mm
– Hallway dimensions (H × W × D):
Concealed installation:
103 × 103 × 66.5 mm
Surface-mounted installation:
123 × 123 × 62 mm
– Power supply:
KNX bus voltage 21-30 V
– Mounting height:
2 - 4 m
– Angle of coverage:
360°
– HF 360-2 reach:
ø 12 m
– Hallway reach:
24 × 3 m
– Sensor values:
Light measurement,
Temperature: 0-40°C,
Relative humidity: 0-100%
– Outputs:
4 × light output
(ON/OFF, scenario dimming level),
Dimming level with effect light,
2× constant-lighting control with
basic light level,
HVAC, presence, temperature,
relative humidity, dew point,
logic gate,
comfort, anti-presence
– Time setting:
30 seconds to 18:12:15 hours
(hh:mm:ss), IQ mode
– Twilight setting:
2-1000 lux
– Temperature range:
0°C to +40°C
– IP rating:
IP20
– Bluetooth frequency:
2.4-2.48 GHz
– Bluetooth transmission power:
5 dBm/3 mW
– HF 360/Hallway frequency:
5.8 GHz
– Transmission power:
3 dBm/2 mW
4. Electrical connection
Surface-mounted connection (Fig. 4.1)
Concealed connection (Fig. 4.2)
5. Installation
• Check all components for damage.
• Do not use the product if it is dam-
aged.
• Select an appropriate mounting
location, taking the reach and
motion detection into consideration.
(Fig. 3.13/3.14)
• Aim sensor in appropriate direction.
Hallway KNX (Fig. 5.1)
Mounting procedure
• Switch off power supply (Fig. 4.1/4.2)
Concealed mounting
• Make plug connection. (Fig. 5.2)
• Firmly screw load module into mount-
ing box. (Fig. 5.3)
• Fit magnetic sensor module on frame.
(Fig. 5.4)
• Switch ON power supply. (Fig. 5.4)
• Make settings.
➜ "6. Function and settings"
Surface mounting
• Mark drill holes and drill. (Fig. 5.5)
• Screw load module into place.
(Fig. 5.6)
• Make plug connection. (Fig. 5.7)
• Break out the mounting tab. (Fig. 5.8)
• Fit surface-mounting adapter.
(Fig. 5.9)
• Fit magnetic sensor module.
(Fig. 5.10)
• Switch ON power supply. (Fig. 5.10)
• Make settings.
➜ "6. Function and settings"
- 13 -
Advertisement
Table of Contents
