1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Network Hardware
  5. eMerge Enterprise
  6. Install and setup manual

IEI Technology eMerge Enterprise Install And Setup Manual

Hide thumbs Also See for eMerge Enterprise:
Table of Contents

Advertisement

Quick Links

Download this manual
IEI eMerge™ Enterprise and Enterprise Ultra
Install and Setup Guide
Configuring Your eMerge Enterprise ................................................................ 2
Connecting Power and the Network to the eMerge Enterprise .................................................. 2
Configuring IP Settings ............................................................................................................... 3
Logging in to your eMerge Enterprise ......................................................................................... 4
Connecting Nodes and Configuring System Resources ............................................................ 4
Specifications ..................................................................................................... 6
Front Panel LEDs ........................................................................................................................ 6
Reset Switches and Drive Lights ................................................................................................ 7
The eMerge Enterprise Hard Drives ........................................................................................... 8
Migrating from eMerge 3.X to eMerge Enterprise 3.X ...................................... 9
Contents
Version 3.1 and above
1

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology eMerge Enterprise

Summary of Contents for IEI Technology eMerge Enterprise

  • Page 1: Table Of Contents

    Install and Setup Guide Contents Configuring Your eMerge Enterprise ..............2 Connecting Power and the Network to the eMerge Enterprise ..........2 Configuring IP Settings ....................... 3 Logging in to your eMerge Enterprise ..................4 Connecting Nodes and Configuring System Resources ............4 Specifications .....................

  • Page 2: Configuring Your Emerge Enterprise

    Enterprise or Enterprise Ultra. See the images below. 2. Connect the network cable to the network connector on the back of the eMerge Enterprise or Enterprise Ultra. Be sure the place the cable in the correct connector as shown below.

  • Page 3: Configuring Ip Settings

    2. You can edit any of the settings on this page. NOTE: If you change the IP address of the eMerge Enterprise be sure to take note of the new address as you will need it to log in later.

  • Page 4: Logging In To Your Emerge Enterprise

    Logging in to your eMerge Enterprise Login NOTE: The default IP address of an eMerge Enterprise is 192.168.0.250. If you changed this in previous steps then enter the new address here. 1. Open your browser and enter the Enterprise IP address into the address line. Press the Enter 2.
  • Page 5 10. If some nodes still will not connect it may be necessary to adjust port forwarding on routers and gateways to allow the nodes on different subnets to communicate with the controller. See Tech Note 1 for details. NOTE: It may also be necessary to use nnconfig.exe to assign a specific controller IP address to each remote node, rather than to allow nodes to Auto Discover the controller.

  • Page 6: Specifications

    Specifications The IEI eMerge Enterprise is a 19” 1U rack mount disk-based network appliance that gives you greater capacity for applications of greater scale and complexity than a standard solid-state eMerge controller. The Enterprise Ultra is a 19” 2U rack mount network appliance that gives you maximum capacity for applications of greater scale and complexity.

  • Page 7: Reset Switches And Drive Lights

    Off or On Red: Drive failure System This button restarts the Enterprise controller processes. Reset The eMerge Enterprise has an audible alarm which sounds when the Alarm Reset power, temperature, or the fan are in an abnormal state. Press this to stop the audible alarm.

  • Page 8: The Emerge Enterprise Hard Drives

    The eMerge Enterprise Hard Drives The eMerge Enterprise comes equipped with an 80 gigabyte hard drive. This drive can be replaced but the unit must first be powered down. The eMerge Enterprise Ultra comes equipped with hot swappable RAID 1 mirrored drives. The drives are 80 Gigabytes each.

  • Page 9: Migrating From Emerge 3.X To Emerge Enterprise 3.X

    NOTE: By default, nodes come from the factory set to DHCP. Start the eMerge Enterprise and restore the data backup NOTE: If you set your eMerge Enterprise IP settings to the same settings as the previous controller then router settings, port forwarding settings, and Node auto-discovery settings will not need to be changed.
  • Page 10 NOTE: The default IP address of an eMerge Enterprise is 192.168.0.250. If you changed this in previous steps then enter the new address here. 4. At the Login page enter the User name “admin.” 5. Enter the Password “admin.” 6. Click Go. The security application will now display.
  • Page 11 8. If any nodes are not yet connected to the Enterprise controller, return to step 1 in this procedure and ensure that all nodes are enabled. 9. If some nodes still will not connect it may be necessary to adjust port forwarding on routers and gateways to allow the nodes on different subnets to communicate with the controller.

This manual is also suitable for:

Emerge enterprise ultra

Table of Contents