Desktop network appliance with intel atom c3000 series processor, four ddr4, six gbe ports, two 10gbe sfp+, two m.2, pcie mini, rack mount, and rohs compliant (86 pages)
Page 1
ECK-3699GH Embedded System ECK-3699GH User Manual Page 1...
Page 2
ECK-3699GH Embedded System REVISION HISTORY Title ECK-3699GH Intel Pentium 4 / Celeron D Embedded System Revision Number Description Date of Issue Initial release January 2007 COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
ECK-3699GH Embedded System Table of Contents 1......................INTRODUCTION ............................13 1.1 ECK-3699GH E ............14 MBEDDED YSTEM VERVIEW 1.1.1 ECK-3699GH Benefits..................14 1.1.2 ECK-3699GH Features..................14 1.2 T ..................15 ECHNICAL PECIFICATIONS 1.3 P ................16 OWER ODULE PECIFICATIONS 1.4 P .....................
Page 4
ECK-3699GH Embedded System 3.1.1 ECK-3699GH Embedded System Motherboard..........32 3.1.2 KINO-6614 Motherboard Overview ..............32 3.1.3 Onboard Connectors and Jumpers ..............33 3.1.4 External Interface Connectors................. 34 3.1.5 Onboard Jumpers..................... 35 3.2 KINO-6614 O ............35 BOARD ONNECTOR INOUTS 3.2.1 ATX Power Connector ..................35 3.2.2 CPU Power Connector ..................
Page 5
ECK-3699GH Embedded System 4.2.3.1 Top Cover Removal .................. 57 4.3 S LGA775 CPU I ..............58 OCKET NSTALLATION 4.3.1 CPU Selection: HT Functionality Requirements ..........58 4.3.1.1 CPU Installation..................58 4.3.2 Cooling Kit Installation ................... 63 4.3.3 Configure the Jumper Settings................. 64 4.3.4 DIMM Module Installation ................
Page 6
ECK-3699GH Embedded System 5.4 PCI/P P ........................97 5.5 B ........................102 5.5.1 Boot Settings Configuration................102 5.5.2 Boot Device Priority ..................106 5.5.3 Hard Disk Drives ................... 106 5.5.4 Removable Drives ..................107 5.5.5 CD/DVD Drives ..................... 108 5.6 S .......................
Page 7
ECK-3699GH Embedded System 7.3.3.2 Power Module Installation..............155 7.3.4 Cooling Fan Replacement................156 A................IEI EMBEDDED SYSTEM SERIES ............................159 A.1 IEI E ................160 MBEDDED YSTEM ERIES A.1.1 Overview......................160 A.1.2 IEI Embedded System Series ................. 160 A.1.3 IEI Embedded System Series Variations............160 A.2 E...
Page 8
ECK-3699GH Embedded System List of Figures Figure 1-1: ECK-3699GH KINO Series Embedded System ........14 Figure 1-2: Power Adapter ..................17 Figure 1-3: ECK-3699GE Cooling Kit.................18 Figure 2-1: ECK-3699GH Dimensions (mm) .............22 Figure 2-2: KINO SBC Dimensions (mm) ..............23 Figure 2-3: Power Module Dimensions (mm) ............23 Figure 2-4: ECK-3699GH Front Panel................24...
Page 9
Figure 4-5: Remove the CPU Socket Protective Shield...........61 Figure 4-6: Open the CPU Socket Load Plate ............61 Figure 4-7: Insert the Socket LGA775 CPU ..............62 Figure 4-8: ECK-3699GH Cooling Kit ................63 Figure 4-9: Securing the Cooling Kit.................64 Figure 4-10: Installing the DIMM Module ..............66 Figure 4-11: Locking the DIMM Module ..............66...
Page 10
ECK-3699GH Embedded System Figure 6-19: Audio Driver Installation Complete........... 133 Figure 6-20: Access Windows Control Panel............134 Figure 6-21: Double Click the System Icon ............135 Figure 6-22: Double Click the Device Manager Tab..........135 Figure 6-23: Device Manager List ................136 Figure 6-24: Search for Suitable Driver..............
Page 11
ECK-3699GH Embedded System List of Tables Table 1-1: Technical Specifications ................16 Table 1-2: Power Module Specifications..............16 Table 1-3: Power Adapter Specifications..............18 Table 1-4: CPU Cooling Kit Specifications ...............19 Table 2-1: Cooling Fan Specifications ..............30 Table 3-1: Peripheral Interface Connectors..............34 Table 3-2: Peripheral Interface Connectors..............34 Table 3-3: Onboard Jumper ..................35...
Page 12
ECK-3699GH Embedded System List of BIOS Menus BIOS Menu 1: Main......................72 BIOS Menu 2: Advanced.....................74 BIOS Menu 3: CPU Configuration................75 BIOS Menu 4: IDE Configuration ................76 BIOS Menu 5: IDE Master and IDE Slave Configuration..........80 BIOS Menu 6: Floppy Configuration .................84 BIOS Menu 7: Super IO Configuration ..............85...
The KINO series boards support a full range of functions for an AT/ATX-compatible industrial computer. 1.1.1 ECK-3699GH Benefits The ECK-3699GH embedded system has the following benefits: Easy installation saves installation time Complete integration saves solution development time and cost...
ECK-3699GH Embedded System 1.2 Technical Specifications The specifications for the ECK-3699GH embedded systems are listed below. ECK-3699GH ® ® ® Intel Pentium 4 / Celeron D with 533/800 MHz FSB System Chipset SiS661CX + SiS966 System Memory Speed DDR 400MHz or 333MHz...
45mm x 160mm Temperature: 80°C Table 1-2: Power Module Specifications 1.4 Power Adapter The ECK-3699GH models are shipped with a 150W power adapter. Figure 1-2: Power Adapter The specifications for the adapter are listed in Table 1-3: Nominal 19.0V Regulation 18.5V to 19.9V...
ECK-3699GH Embedded System Time Hold Up Min. 264V Max. Frequency 47Hz ~ 63Hz Input No damage (cold start) Inrush Current Max. AC Current 2A@100VAC Efficiency Operating 10ºC ~ 40ºC Temperature Storage 0ºC ~ 85ºC Environment Storage 5% ~ 95% Relative Humidity...
ECK-3699GH Embedded System Rated Voltage 12V DC Operating Range 5V~13.2V DC Consuming Current 0.45A (Max.) Consuming Power 5.40W (Max.) 4800rpm ± 10%rpm Rated Speed Airflow 28.74 CFM (at rated voltage) 3.34mmH Static Pressure Operating -10ºC~70ºC Temperature Storage Temperature -20ºC ~75ºC...
Page 20
ECK-3699GH Embedded System THIS PAGE IS INTENTIONALLY LEFT BLANK Page 20 IEI ® Technology, Corp.
ECK-3699GH Embedded System 2.1 ECK-3699GH Mechanical Overview The ECK-3699GH is made of a metal chassis. The chassis is covered with a top cover and comprises multiple air vents to allow for the free flow of cooling air through the system.
ECK-3699GH Embedded System 2.2.2 Motherboard Dimensions The KINO series dimension are listed below and shown in Figure 2-2. Length: 170.00mm Width: 170.00mm Figure 2-2: KINO SBC Dimensions (mm) 2.2.3 Power Module Dimensions The power module dimensions are listed below and shown in Figure 2-3.
ECK-3699GH Embedded System 2.3 External Overview 2.3.1 Front Panel 2.3.1.1 Front Panel Overview The front panel of the ECK-3699GH contains indicators, buttons, USB ports and CD drive bay. See Figure 2-4. Figure 2-4: ECK-3699GH Front Panel 2.3.1.2 Front Panel Buttons and Indicators The connectors, indicators and buttons listed in this section are shown in Figure 2-4 above.
All the front panel items listed above are shown in Figure 2-4 above. 2.3.2 Rear Panel 2.3.2.1 Rear Panel Overview The ECK-3699GH contains all the external I/O interface connectors, power connectors and audio jacks. An overview of the rear panel is shown in Figure 2-5 below. Figure 2-5: ECK-3699GH Rear Panel 2.3.2.2 Rear Panel Connectors...
Before removing the top cover, make sure the system has been turned off and all power connectors unplugged. The top cover of the ECK-3699GH covers the top and both sides of the ECK-3699GH. The top cover is secured to the ECK-3699GH with three retention screws on the rear panel.
ECK-3699GH Embedded System 2.3.4 Bottom Surface The bottom surface of the ECK-3699GH contains one air vent. Figure 2-7: Bottom Surface 2.4 Internal Overview The ECK-3699GH internal components are listed below: 1 x IEI KINO motherboard 1 x Power module 2 x System cooling fans...
ECK-3699GH Embedded System Figure 2-8: ECK-3699GH Internal Overview 2.5 Cooling Fans The embedded system has two internal cooling fans mounted at the right side of the chassis and connected directly to the power module. The cooling fan dimensions are shown in Figure 2-9 and the specifications are shown in Table 2-1.
ECK-3699GH Embedded System Figure 2-9: Cooling Fan Dimensions (mm) Specification Units Details 60 x 60 x 11 (L x W x Thickness) Dimensions Bearing System Dual Ball Bearing, NMB or ISC 12.0 Rated Voltage Operating Voltage 11.0~15.0 at 25 °C...
ECK-3699GH Embedded System and 25 °C, rated speed Static Air Pressure 1.18 at zero air flow and 25 °C Operating Temperature -10°C,~+70°C, /66%(RH) Storage Temperature -40°C,~+70°C, /66%(RH) Noise Level 22.0 at rated voltage Environment Humidity Less than 85%(RH) Life Expectancy...
The ECK-3699GH models have a KINO-6614 motherboard installed in the system. The following sections describe the relevant connectors and jumpers on the motherboard. 3.1.2 KINO-6614 Motherboard Overview The locations of the KINO-6614 jumpers and connectors used on the ECK-3699GH are shown in Figure 3-1 below. Page 32...
ECK-3699GH Embedded System Figure 3-1: KINO-6614 Jumper and Connector Locations 3.1.3 Onboard Connectors and Jumpers The connectors listed in Table 3-1 on the KINO-6614 motherboard are connected to front panel components, storage devices and the power module as specified later in this chapter.
ECK-3699GH Embedded System IDE Interface connector (Secondary) 40-pin box header SIDE1 System fan connector 3-pin wafer connector SYS_FAN1 System fan connector 3-pin wafer connector SYS_FAN2 SATA connector 7-pin SATA connector S_ATA1 SATA connector 7-pin SATA connector S_ATA2 USB connector (1)
ECK-3699GH Embedded System 3.1.5 Onboard Jumpers Table 3-3 lists the onboard jumper. Detailed descriptions of the jumper can be found in Section 3.3.2. For a more comprehensive list of jumpers and connectors, please refer to KINO-6614 user manual. Description Label...
ECK-3699GH Embedded System The connector supports the 12V power supply. Figure 3-3: CPU 12V Power Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION +12V +12V Table 3-5: CPU 12V Power Connector Pinouts 3.2.3 Fan Connectors CN Label: SYS_FAN1 and SYS_FAN2...
ECK-3699GH Embedded System Figure 3-5: Front Panel Connector Location DESCRIPTION DESCRIPTION Power PWRBTN+ PWRLED+ Power LED Button PWRBTN- PWRLED- HD LED HDDLED+ RESET+ RESET HDLED- RESET- Table 3-7: Front Panel Connector Pinouts 3.2.5 IDE Connectors CN Label: PIDE1 and SIDE1...
ECK-3699GH Embedded System Figure 3-6: IDE Device Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION RESET# DATA 7 DATA 8 DATA 6 DATA 9 DATA 5 DATA 10 Page 40 IEI ® Technology, Corp.
ECK-3699GH Embedded System PIN NO. DESCRIPTION PIN NO. DESCRIPTION DATA 4 DATA 11 DATA 3 DATA 12 DATA 2 DATA 13 DATA 1 DATA 14 DATA 0 DATA 15 IDE DRQ IOW# IOR# IDE CHRDY BALE – DEFAULT IDE DACK...
ECK-3699GH Embedded System Figure 3-7: SATA Drive Connector Locations PIN NO. DESCRIPTION Table 3-9: SATA Drive Connector Pinouts 3.2.7 Internal USB Connectors CN Label: USB46 and USB57 CN Type: 8-pin header (2x4) CN Location: See Figure 3-8 CN Pinouts: See Table 3-10 One 2x4 pin connector provides connectivity to two USB 2.0 ports.
Figure 3-9 shows the KINO-6614 motherboard external interface connectors. These external interface connectors can connect to external peripheral devices and are seen on the rear panel (Figure 2-5) of the ECK-3699GH embedded system. The KINO-6614 on-board external interface connectors are listed below and shown in Figure 3-9:...
ECK-3699GH Embedded System Figure 3-9: KINO-6614 On-board External Interface Connectors 3.3.2 Audio Connectors CN Label: AUDIO_CV1 CN Type: Audio jack CN Location: See Figure 3-9 (labeled number 7) CN Pinouts: See Figure 3-10 Line Out port (Lime): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers.
ECK-3699GH Embedded System 3.3.3 Ethernet Connectors CN Label: LAN1_USB01 and LAN2_USB23 CN Type: RJ-45 CN Location: See Figure 3-9 (labeled number 4 and 6) CN Pinouts: See Table 3-11 The KINO-6614 is equipped with two built-in GbE Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors.
ECK-3699GH Embedded System SPEED LED ACT/LINK LED STATUS DESCRIPTION STATUS DESCRIPTION GREEN 10/100Mbps connection YELLOW Linked ORANGE 1Gbps connection BLINKING Data Activity Table 3-12: RJ-45 Ethernet Connector LEDs 3.3.4 USB Connectors CN Label: LAN1_USB01 and LAN2_USB23 CN Type: USB port...
ECK-3699GH Embedded System 3.3.5 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: PS/2 connector CN Location: See Figure 3-9 (labeled number 1) CN Pinouts: See Table 3-14 and Table 3-15 The KINO-6614 keyboard and mouse connectors are standard PS/2 connectors. Figure 3-13: PS/2 Pinouts...
ECK-3699GH Embedded System Table 3-15: Mouse Connector Pinouts 3.3.6 Serial Port Connectors CN Label: COM_C1 CN Type: D-sub 9 male connector CN Location: See Figure 3-9 (labeled number 9) CN Pinouts: See Table 3-16 The serial ports can be connected to a serial communications device directly.
ECK-3699GH Embedded System 3.3.7 VGA Connector CN Label: VGA1 CN Type: 15-pin female connector CN Location: See Figure 3-9 (labeled number 8) CN Pinouts: See Table 3-17 The standard 15-pin VGA connector connects to a CRT or LCD display monitor.
ECK-3699GH Embedded System CN Location: See Figure 3-9 (labeled 2) CN Pinouts: See Figure 3-16 and Table 3-18 The KINO-6614 motherboard includes one external parallel port, accessed through 25-pin D-type female connector LPT1. These ports are usually connected to a printer.
ECK-3699GH Embedded System 3.4 KINO-6614 Motherboard On-board Jumpers NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
ECK-3699GH Embedded System Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. Clear CMOS DESCRIPTION Short 1-2 Normal Operation (Default) Short 2-3 Clear CMOS Setup Table 3-19: Clear CMOS Jumper Settings The clear CMOS jumper is located in Figure 3-18.
ECK-3699GH Embedded System Figure 3-19: Power Module Connector Locations The pin outs for these connectors are listed in the sections below. 3.5.1 Input Power Connector The input power connector, CN1, is connected directly to the rear panel power socket. Power is received in this connector from an external power source and fed into the system.
ECK-3699GH Embedded System +12V Table 3-22: Output Power Connector Pinouts [CPU Power] 3.5.3 Output Power Connector [Motherboard] The 20-pin output power connector, PW2, is connected directly to the main ATX power connector (ATX20) on the KINO series motherboard. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 3.3V...
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO series motherboard and the power module. (Dry climates are especially susceptible to ESD.) It is therefore critical that whenever the ECK-3699GH is opened and any electrical component handled, the following anti-static precautions are strictly adhered to.
ECK-3699GH Embedded System 4.2.2 Unpacking After the ECK-3699GH is received make sure the following components are included in the package. If any of these components are missing, please contact the ECK-3699GH reseller or vendor where it was purchased or contact an IEI sales representative immediately.
ECK-3699GH Embedded System Figure 4-1: Top Cover Retention Screws Step 2: Slide the top cover toward the rear panel and gently lift the cover off the chassis Step 0: 4.3 Socket LGA775 CPU Installation 4.3.1 CPU Selection: HT Functionality Requirements...
ECK-3699GH Embedded System please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure that a heat sink and CPU cooling fan are properly installed before the KINO-6614 is run. If a heat sink and cooling fan are not properly installed both the CPU and the board may be damaged.
ECK-3699GH Embedded System USB connector Figure 4-3: Motherboard Connectors Step 3: Remove the KINO-6614 retention screws. The motherboard is secured to the chassis with four retention screws. Remove the four retention screws. See Figure 4-4. Figure 4-4: Motherboard Retention Screws Step 4: Remove the protective cover.
ECK-3699GH Embedded System Figure 4-5: Remove the CPU Socket Protective Shield Step 5: Open the socket. Disengage the load lever by pressing the lever down and slightly outward to clear the retention tab. Rotate the load lever to a fully open position.
ECK-3699GH Embedded System Step 9: Align the CPU pins. Locate pin 1 and the two orientation notches on the CPU. Carefully match the two orientation notches on the CPU with the socket alignment keys. Step 10: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly.
4.3.2 Cooling Kit Installation Figure 4-8: ECK-3699GH Cooling Kit IEI provides a CPU cooling kit designed for the ECK-3699GH. (Figure 4-8) The cooling kit is comprised of a CPU heat sink and a cooling fan. To install the ECK-3699GH CPU cooling kit, please follow the steps below.
ECK-3699GH Embedded System Figure 4-9: Securing the Cooling Kit Step 5: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each nut a few turns at a time and do not over-tighten the screws. Step 6: Connect the fan cable. Connect the cooling kit fan cable to the CPU fan connector on the motherboard.
Please only use DDR DIMM modules. 4.3.4.2 DIMM Module Installation The ECK-3699GH has two DDR SDRAM DIMM socket. Follow the steps below to install the DIMM module. Step 1: Make sure the two handles of the DIMM socket are in the "open" position, leaning outward (Figure 4-10).
ECK-3699GH Embedded System Figure 4-10: Installing the DIMM Module Step 2: Slowly slide the DIMM module along the plastic guides on both ends of the socket. Press the DIMM module down into the socket until it clicks into position and the two handles have automatically locked the memory module into place (Figure 4-11).
HDD bracket with the retention screw holes on the bottom of the HDD. Insert four retention screws into the bracket on the bottom of the HDD Step 4: Install the HDD bracket into the ECK-3699GH. Step 5: Connect the IDE/SATA cable from the IDE/SATA connector on the motherboard to the rear of HDD.
All peripheral devices (VGA monitor, serial communications devices etc.) are connected The power cables are plugged in 4.4.2 Power-on Procedure To power-on the ECK-3699GH please follow the steps below: Step 1: Push the power button. Step 2: Once turned on, the green power LED should be turned on. See Figure 4-12.
ECK-3699GH Embedded System 5.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.
ECK-3699GH Embedded System F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears.
ECK-3699GH Embedded System BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed. The items shown in the system overview include: AMI BIOS: Displays auto-detected BIOS information...
ECK-3699GH Embedded System System Time [xx:xx:xx]: The system time is set here. System Date [Day xx/xx/xxxx]: The system date is set here. 5.3 Advanced The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device configuration options through the following sub-menus:...
ECK-3699GH Embedded System BIOS Menu 2: Advanced 5.3.1 CPU Configuration The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and CPU configuration options. Page 74 IEI ® Technology, Corp.
ECK-3699GH Embedded System BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed...
ECK-3699GH Embedded System Enabled The clock spread spectrum is enabled 5.3.2 IDE Configuration The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. BIOS Menu 4: IDE Configuration OnBoard PCI IDE Controller [Both] Use the OnBoard PCI IDE Controller BIOS option to specify the IDE channels used by the onboard PCI IDE controller.
Page 77
ECK-3699GH Embedded System Primary Slave Secondary Only allows the system to detect the Secondary IDE channel, including both the Secondary Master and Secondary Slave Both Allows the system to detect both the Primary and EFAULT Secondary IDE channels including the Primary Master, Primary Slave, Secondary Master and Secondary Slave.
Page 78
ECK-3699GH Embedded System Fourth IDE Slave The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. If an IDE device is detected, and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 5.3.2.1 appear.
ECK-3699GH Embedded System Use the ATA (PI) 80Pin Cable Detection option to enable the system to detect the correct cable. When an Ultra ATA/66, an Ultra ATA/100 or an Ultra ATA/133 IDE hard disk drive is used, an 80-conductor ATA cable must be used. The 80-conductor ATA cable is plug compatible with the standard 40-conductor ATA cable.
ECK-3699GH Embedded System BIOS Menu 5: IDE Master and IDE Slave Configuration Auto-Detected Drive Parameters The “grayed-out” items in the left frame are IDE disk drive parameters automatically detected from the firmware of the selected IDE disk drive. The drive parameters are listed as follows: Device: Lists the device type (e.g.
Page 81
ECK-3699GH Embedded System Ultra DMA: Indicates the highest Synchronous DMA Mode that is supported. S.M.A.R.T.: Indicates whether or not the Self-Monitoring Analysis and Reporting Technology protocol is supported. Type [Auto] The Type BIOS option determines the type of device that the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) has completed.
Page 82
ECK-3699GH Embedded System mode control on the specified channel. Auto This option allows the BIOS to auto detect the LBA mode EFAULT control on the specified channel. Block (Multi Sector Transfer) [Auto] Disabled Selecting this option prevents the BIOS from using Multi-Sector Transfer on the specified channel.
Page 83
ECK-3699GH Embedded System manufactured after 1999. For other disk drives, such as IDE CD-ROM drives, check the specifications of the drive.) DMA Mode [Auto] The DMA Mode BIOS selection adjusts the DMA mode options. Auto The BIOS auto detects the DMA mode. Use this value if the EFAULT IDE disk drive support cannot be determined.
ECK-3699GH Embedded System 5.3.3 Floppy Configuration Use the Floppy Configuration menu (BIOS Menu 6) to set or change the configurations for floppy disk drives. BIOS Menu 6: Floppy Configuration Floppy A [1.44 MB 3½”] The Floppy A configuration option determines the types of the floppy drive installed in the system.
ECK-3699GH Embedded System 5.3.4 Super IO Configuration The Super IO Configuration menu (BIOS Menu 7) sets or changes the configurations for the FDD controllers, parallel ports and serial ports. BIOS Menu 7: Super IO Configuration OnBoard Floppy Controller [Enabled] Use the OnBoard Floppy Controller to enable or disable the floppy controller. If a floppy disk is not being used in the system, disabling this option frees up system resources that can be redirected elsewhere in the system.
Page 86
ECK-3699GH Embedded System Disabled No base address is assigned to Serial Port 1 3F8/IRQ4 Serial Port 1 I/O port address is 3F8 and the interrupt EFAULT address is IRQ4 3E8/IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt...
Page 87
ECK-3699GH Embedded System Disabled No base address is assigned to the Parallel Port Parallel Port I/O port address is 378 EFAULT Parallel Port I/O port address is 278 Parallel Port I/O port address is 3BC Parallel Port Mode [Normal] Use the Parallel Port Mode option to select the mode the parallel port operates in.
ECK-3699GH Embedded System Parallel Port IRQ [IRQ7] Use the Parallel Port IRQ selection to set the parallel port interrupt address. IRQ5 IRQ5 is assigned as the parallel port interrupt address IRQ7 IRQ7 is assigned as the parallel port interrupt address EFAULT 5.3.5 Hardware Health Configuration...
ECK-3699GH Embedded System Fan Speeds: The CPU cooling fan speed is monitored. Voltages: The following system voltages are monitored Vcore +3.3Vin +5Vin +12Vin –12Vin –5Vin 5.3.6 ACPI Configuration The ACPI Configuration menu (BIOS Menu 9) configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options.
ECK-3699GH Embedded System ACPI Aware O/S [Yes] Use the ACPI Aware O/S option to enable the system to configure ACPI power saving options. ACPI can only be implemented if the system OS complies with the ACPI standard. Windows 98, Windows 2000, and Windows XP all comply with ACPI.
ECK-3699GH Embedded System ACPI Version Features [ACPI v2.0] Use the ACPI Version Features option to enable the ACPI (Advanced Configuration and Power Interface) features. By enabling this feature the system RSDP (Root System Description Pointer) is able to obtain physical addresses for other 64-bit fixed system description tables.
ECK-3699GH Embedded System BIOS Menu 11: MPS Configuration MPS Revision [1.4] Use the Multiprocessor Specification (MPS) for OS option to specify the MPS version to be used. MPS version 1.1 is used MPS version 1.4 is used EFAULT 5.3.8 USB Configuration Use the USB Configuration menu (BIOS Menu 12) to read USB configuration information and configure the USB settings.
ECK-3699GH Embedded System BIOS Menu 12: USB Configuration Onboard SiS USB1.1 DEVICE [Enabled] Use the Onboard SiS USB1.1 DEVICE BIOS option to enable or disable the onboard SiS USB1.1 controller. If disabled, USB1.1 devices cannot be used. Disabled USB 1.1 interface is disabled and cannot be used.
Page 94
ECK-3699GH Embedded System USB Configuration The USB Configuration field shows the system USB configuration. The items listed are: Module Version: x.xxxxx.xxxxx USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.
ECK-3699GH Embedded System Disabled Systems with OSes that do not support EHCI can use the EHCI handoff functionality. Systems with OSes that do not support EHCI cannot Enabled EFAULT use the EHCI handoff functionality. 5.3.8.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 13) to configure USB mass storage class devices.
Page 96
ECK-3699GH Embedded System Emulation Type [Auto] Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide for the USB device. NOTE: Please note that the device’s formatted type and the emulation type provided by the BIOS must match for a device to boot properly. If both types do not match then device’s behavior is undefined.
ECK-3699GH Embedded System option. 5.4 PCI/PnP Use the PCI/PnP menu (Error! Reference source not found.) to configure advanced PCI and PnP settings. WARNING! Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
Page 98
ECK-3699GH Embedded System Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared when the power is turned off. System does not clear NVRAM during system boot EFAULT System clears NVRAM during system boot Plug & Play O/S [No] Use the Plug &...
Page 99
ECK-3699GH Embedded System Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA adapter card an interrupt address. Assigns an IRQ to a PCI VGA card if card requests IRQ EFAULT Does not assign IRQ to a PCI VGA card even if the card...
Page 100
ECK-3699GH Embedded System Auto The location of the Off Board PCI IDE adapter card is EFAULT automatically detected by the AMIBIOS. PCI Slot 1 is selected as the location of the OffBoard PCI Slot 1 PCI IDE adapter card. Only select this slot if the adapter card is installed in PCI Slot 1.
Page 101
ECK-3699GH Embedded System devices Available IRQ addresses are: IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device. Available...
ECK-3699GH Embedded System Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices. Disabled No memory block reserved for legacy ISA devices EFAULT 16KB reserved for legacy ISA devices...
ECK-3699GH Embedded System Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced system boot options. BIOS Menu 16: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process.
Page 104
ECK-3699GH Embedded System Enabled OEM Logo displayed instead of POST messages AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS The system forces third party BIOS to display EFAULT during system boot.
Page 105
ECK-3699GH Embedded System Disabled PS/2 mouse support is disabled and prevented from using system resources. Allows the system to use a PS/2 mouse. Enabled EFAULT Auto Mode The system auto-adjusts PS/2 mouse support. Wait For ‘F1’ If Error [Enabled] Use the Wait For ‘F1’ if Error option to specify how the system responds when the system detects an error on boot up.
ECK-3699GH Embedded System Use the Interrupt 19 Capture option to allow optional ROMs such as network controllers to trap BIOS interrupt 19. Disabled Does not allow optional ROM to trap interrupt 19 EFAULT Enabled Allows optional ROM to trap interrupt 19 5.5.2 Boot Device Priority...
ECK-3699GH Embedded System Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. When the menu is opened, the HDDs connected to the system are listed as shown below: 1st Drive [HDD: PM-(part number)] NOTE: Only the drives connected to the system are shown.
ECK-3699GH Embedded System BIOS Menu 18: Removable Drives 5.5.5 CD/DVD Drives Use the CD/DVD Drives menu to specify the boot sequence of the available CD/DVD drives. When the menu is opened, the CD drives and DVD drives connected to the system...
ECK-3699GH Embedded System The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available CD/DVD drives is shown. Select the first CD/DVD drive the system boots from. If the “1st Drive” is not used for booting this option may be disabled.
ECK-3699GH Embedded System Change User Password Use the Change User Password to set or change a user password. The default for this option is Not Installed. If a user password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change User Password.
ECK-3699GH Embedded System 5.7.1 North Bridge Configuration Use the NorthBridge Configuration menu (BIOS Menu 21) to configure the northbridge chipset. BIOS Menu 21:NorthBridge Chipset Configuration Primary Graphics Adapter [PCI] Use the Primary Graphics Adapter option to select the graphics adapter the system uses.
Page 112
ECK-3699GH Embedded System receipt of a "read" command and when the RAM chip actually starts reading. The BIOS options are as follows: By SPD EFAULT 2.5T Graphic Win Size [64MB] Use the Graphic Win Size option to select the size of the AGP aperture and the size of the GART (Graphics Address Relocation Table).
ECK-3699GH Embedded System CTR1 only EFAULT CRT1 + LCD CRT1 + TV CRT1 + CRT2 LCD Display Type [Full Screen] Use the LCD Display Type BIOS to specify the screen display type. Configuration options are listed below: Full Screen EFAULT...
ECK-3699GH Embedded System BIOS Menu 22: SouthBridge Chipset Configuration OnBoard Audio DEVICE [Enabled] Use the OnBoard Audio DEVICE option to enable or disable the AC’97 CODEC. The onboard AC’97 is disabled Disabled Enabled The onboard AC’97 is enabled EFAULT All PCI EXPRESS Controller [Enabled] Use the All PCI EXPRESS Controller option to determine enable or disable the PCI Express controller.
ECK-3699GH Embedded System All PCI EXPRESS INTPIN [Disabled] Use the All PCI EXPRESS INTPIN option to determine enable or disable the PCI Express interrupt pin. Disabled The PCI Express interrupt pin is disabled. EFAULT The PCI Express interrupt pin is enabled.
ECK-3699GH Embedded System BIOS Menu 23: Power Power Management/APM [Enabled] Use the Power Management/APM BIOS option to enable access to the advanced power management features. If this option is disabled, the only other option on the screen is the Power Button Mode.
ECK-3699GH Embedded System Disabled Wake event not generated by PCI PME controller EFAULT activity Wake event generated by PCI PME controller activity Enabled Restore on AC Power Loss [Last State] Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.
ECK-3699GH Embedded System BIOS Menu 24:Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system.
Page 119
ECK-3699GH Embedded System Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation. Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus.
Page 120
ECK-3699GH Embedded System THIS PAGE IS INTENTIONALLY LEFT BLANK Page 120 IEI ® Technology, Corp.
ECK-3699GH Embedded System 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. You may visit the IEI website or contact technical support for the latest updates.
ECK-3699GH Embedded System Figure 6-1: SIS Solution CD Main Menu Step 2: A window appears listing the drivers available for installation. Step 3: Select any item from the list to view more information on the driver installation, or select Manual to navigate to the KINO-6614 motherboard user manual.
ECK-3699GH Embedded System Figure 6-2: CD VGA Folder Step 3: Double-click the 3.76logo sub-folder to view the folder contents on the CD for the VGA driver (Figure 6-10). Figure 6-3: CD VGA\3.76logo Folder Step 4: Double-click the setup.exe file to begin the driver installation process.
ECK-3699GH Embedded System Step 8: You then select the setup type (see Figure 6-7). Once the setup type is selected, click on the N button in the setup type menu (see Figure 6-7). Figure 6-7: Select Setup Installation Type Step 9: You are then prompted to select a folder to copy the files in (see Figure 6-8).
ECK-3699GH Embedded System Figure 6-8: Select Folders to Copy Files Step 10: Before the files are copied, you can review you selected settings (see Figure 6-9). Once you have completed reviewing your settings, click on the N button. Figure 6-9: Review Settings Step 11: The driver installation will then start.
ECK-3699GH Embedded System Step 12: Once the installation is complete, you will be prompted to read the Read Me file. (see Figure 6-10) Figure 6-10: Read ReadMe File Step 13: Once you have completed reading the Read Me file or it you skip reading the Read Me file, you will be prompted to restart your computer.
ECK-3699GH Embedded System Figure 6-11: Restart the Computer 6.3 Audio Driver Installation To install the audio driver, please follow the steps below. Step 1: Select Audio from the SIS Solution CD driver menu. Step 2: A new window appears showing the folder contents on the CD for the IDE driver.
ECK-3699GH Embedded System Figure 6-12: CD 4-Audio\AC97\Windows Folder Step 3: Double-click the Setup.exe file to begin the driver installation process. Step 4: Once you double click the Setup icon, the install shield wizard for the audio driver starts. See Figure 6-13.
ECK-3699GH Embedded System Figure 6-14: Audio Driver Setup Preparation Step 6: After install shield is prepared, the welcome screen shown in Figure 6-15 appears. To continue the installation process, click the “N ” button. The install shield starts to configure the new software as shown in Figure 6-16.
ECK-3699GH Embedded System Figure 6-16: Audio Driver Software Configuration Step 7: At this stage the “Digital Signal Not Found” screen shown in Figure 6-17 appears. To continue the installation process, click the “Y ” button. The installation notice shown below will appear.
ECK-3699GH Embedded System Step 8: At this stage the clicking the “Y ” button in Figure 6-17 appears, the installation of the driver begins. See Figure 6-18. Figure 6-18: Audio Driver Installation Begins Step 9: After the driver installation process is complete, a confirmation screen shown in Figure 6-19 appears.
ECK-3699GH Embedded System Step 10: The confirmation screen shown in Figure 6-19 allows you to restart the computer immediately after the installation is complete or to restart the computer later. For the settings to take effect the computer must be restarted. Once you have decided when to restart the computer, click the “F...
ECK-3699GH Embedded System Figure 6-21: Double Click the System Icon Step 3: Double click the Device Manager tab (Figure 6-22). Figure 6-22: Double Click the Device Manager Tab Step 4: A list of system hardware devices appears (Figure 6-23). Page 135...
ECK-3699GH Embedded System Figure 6-23: Device Manager List Step 5: Double click the listed device that has question marks next to it. (This means Windows does not recognize the device). Step 6: The Device Driver Wizard appears (Figure 6-24). Click N to continue.
ECK-3699GH Embedded System Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-25). Click N to continue. Figure 6-25: Locate Driver Files Step 8: Select the proper OS folder under the “X:\5-LAN\BROADCOM BCM57xx Drivers” directory (Figure 6-26) in the location browsing window, where “X:\” is the system CD drive.
ECK-3699GH Embedded System Step 9: Click OK to continue. A driver files location menu window appears. Click N continue. The driver is installed.Step 0: 6.5 SiS SATA RAID Utility Installation NOTE: The SATA RAID driver has to be installed in the SATA RAID mode.
ECK-3699GH Embedded System Figure 6-31: License Agreement Step 8: To accept the terms and conditions stipulated in the license agreement, click Page 141...
ECK-3699GH Embedded System Figure 6-32: Install Application Directory Step 9: The Install Application Directory window appears (Figure 6-32). Click to manually select a destination folder for the program, or click N HANGE accept the default directory and continue the installation.
ECK-3699GH Embedded System Figure 6-33: Select Needed Components Step 11: Select the necessary components by clicking the checkboxes and click N continue. Step 12: The Ready to Install window appears (Figure 6-34). Page 143...
ECK-3699GH Embedded System Figure 6-34: Ready to Install Step 13: Click I and the install shield begins to extract and install the files (Figure NSTALL 6-35). Page 144 IEI ® Technology, Corp.
ECK-3699GH Embedded System Figure 6-35: Setup Status Step 14: After the driver installation process is complete, a confirmation screen appears (Figure 6-36). Page 145...
ECK-3699GH Embedded System Figure 6-36: Restart the Computer Step 15: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click F INISH restart the computer.Step 0: Page 146 IEI ®...
Failure to follow these instructions may lead to personal injury and system damage. To preserve the working integrity of the ECK-3699GH embedded system, the system must be properly maintained. If embedded system components need replacement, the proper maintenance procedures must be followed to ensure the system can continue to operate normally.
ECK-3699GH Embedded System Step 4: Plug the system into a monitor and check to see if anything appears on the screen. If the boot-up screen appears it means the power LED has become disconnected. To fix this problem, open the top cover and reconnect the power LED to the motherboard.
ECK-3699GH Embedded System the monitor is properly connected to the system and the monitor is connected to a power supply and turned on. 7.3 Component Replacement Procedure WARNING: Take Anti-Static precautions whenever maintenance is being carried out on the system components. Failure to take anti-static precautions can cause permanent system damage.
ECK-3699GH Embedded System Step 1: Power down the system. Step 2: Disconnect all rear panel peripheral device connectors. Step 3: Remove the top cover. See Section 4.2.3.1. Step 4: Remove the four HDD bracket retention screws inside the chassis (Figure 7-1).
ECK-3699GH Embedded System Figure 7-2: Motherboard Connectors Step 6: Remove the four retention screws that secure the KINO motherboard to the embedded system (Figure 7-3). Figure 7-3: Motherboard Retention Screws Step 7: Remove the KINO motherboard. Step 8: Remove the DIMM Step 9: Remove the CPU heat sink.
ECK-3699GH Embedded System 7.3.2.2 Motherboard Installation To install the new motherboard, please follow the steps below. Step 1: Install the previously removed CPU heat sink. Step 2: Install the previously removed DIMM Step 3: Install the new motherboard into the system. When installing the new motherboard make sure the external peripheral device connectors are properly aligned with the I/O shielding in the system rear panel.
ECK-3699GH Embedded System 7.3.3.1 Power Module Removal To remove the power module, please follow the steps below. Step 1: Turn off the system. Step 2: Disconnect the rear panel power cable from the power socket. Step 3: Remove the top cover. See Section 4.2.3.1.
ECK-3699GH Embedded System Figure 7-5: Power Module Retention Screws Step 6: Remove the power module.Step 0: 7.3.3.2 Power Module Installation To install the new power module, please follow the steps below. Step 1: Install the new power module into the system.
ECK-3699GH Embedded System 7.3.4 Cooling Fan Replacement To replace a cooling fan, please follow the steps below. Step 1: Turn off the system. Step 2: Remove the top cover. See Section 4.2.3.1. Step 3: Remove the fan connector cable from the motherboard (Figure 7-2).
Page 157
ECK-3699GH Embedded System way. Reinsert the four previously removed cooling fan retention screws. Step 7: Place the fan bracket with the fan installed on the system. Reinsert the four previously removed cooling fan retention screws Step 8: Connect the cooling fan cable connector to the motherboard.
Page 158
ECK-3699GH Embedded System THIS PAGE IS INTENTIONALLY LEFT BLANK Page 158 IEI ® Technology, Corp.
Page 159
ECK-3699GH Embedded System Appendix IEI Embedded System Series Page 159...
ECK-3699GH Embedded System A.1 IEI Embedded System Series A.1.1 Overview IEI embedded industrial PC systems are ideal for manufacturing and automation environments where heavy processing demands exist. These systems are designed to operate effectively within high-stress environments that have diverse operational conditions.
ECK-3699GH Embedded System bay (optional) Two cooling One 2.5” drive ECK-3699G KINO None fans bay (optional) Table A-1: Embedded System Series Overview A.2 Embedded System Solutions The different IEI Embedded System solutions are listed below. For further information, please contact an IEI distributor, reseller, vendor or IEI sales representative. Please also visit the IEI website (www.ieiworld.com).
ECK-3699GH Embedded System ® ® A.2.2 AMD Geode GX466 333MHz Solutions ® ® All the models listed in the table below support an AMD Geode GX466 333MHz CPU. Model Number System DC Input Drive Bays Chipset ® ECW-180AS2 CS5536 None ®...
ECK-3699GH Embedded System ® ® A.2.4 VIA MARK 800MHz Solutions ® ® All the models listed in the table below support a VIA MARK 800MHz CPU. Model Number System Chipset DC Input Drive Bays ® ECW-180AS4 VT82C686B None ® ECW-180AS4WD...
ECK-3699GH Embedded System ® ® ® A.2.6 Intel Socket 479 Pentium /Celeron M 2GHz Solutions ® ® ® All the models listed in the table below support an Intel Socket 479 Pentium /Celeron 2GHz CPU with a 400/533MHz FSB (front side bus).
ECK-3699GH Embedded System ® A.2.8 Intel Socket 479 Core Duo/Solo Solutions ® All the models listed in the table below support an Intel Socket 479 Core Duo/Solo CPU with a 667MHz FSB (front side bus). Model Number System Chipset DC Input Drive Bays ®...
Page 166
ECK-3699GH Embedded System THIS PAGE IS INTENTIONALLY LEFT BLANK Page 166 IEI ® Technology, Corp.
Page 167
ECK-3699GH Embedded System Chapter BIOS Menu Options Page 167...
ECK-3699GH Embedded System B.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 5. System Overview .....................72 Clock Spread Spectrum [Disabled]................75 OnBoard PCI IDE Controller [Both] ...............76 SATA Mode Selection [4P(IDE) + 4S(IDE)] ............77 IDE Master and IDE Slave ..................77 Hard Disk Write Protect [Disabled] ................78...
Page 169
ECK-3699GH Embedded System MPS Revision [1.4]....................92 Onboard SiS USB1.1 DEVICE [Enabled] ...............93 Onboard SiS USB2.0 DEVICE [Enabled] ...............93 USB Configuration....................94 USB Devices Enabled .....................94 Legacy USB Support [Enabled] ................94 USB2.0 Controller Mode [FullSpeed]..............94 BIOS EHCI Handoff [Enabled] ................94 Device ## ........................95 Emulation Type [Auto] ....................96...
ECK-3699GH Embedded System Appendix Watchdog Timer Page 171...
Page 172
ECK-3699GH Embedded System NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
Page 173
ECK-3699GH Embedded System NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example program: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
Page 174
ECK-3699GH Embedded System THIS PAGE IS INTENTIONALLY LEFT BLANK Page 174 IEI ® Technology, Corp.
Page 175
ECK-3699GH Embedded System Appendix Address Mapping Page 175...