Download Print this page

Yetter 5500 Series Owner's Manual, Part Identification

Сover crop devastator
Hide thumbs Also See for 5500 Series:

Advertisement

Quick Links

COVER CROP DEVASTATOR
YETTER MANUFACTURING CO.
Founded 1930
Colchester, IL 62326
Toll free: (800)447-5777.
Fax: (309)776-3222
Website: yetterco.com
E-mail: info@yetterco.com
5500 SERIES
5500-001 48"
5500-002 60"
5500-003 90"
OWNER'S MANUAL
PART IDENTIFICATION
2565-976_REV_A ● 03/2020

Advertisement

loading
Need help?

Need help?

Do you have a question about the 5500 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Yetter 5500 Series

  • Page 1 5500 SERIES COVER CROP DEVASTATOR 5500-001 48” 5500-002 60” 5500-003 90” OWNER’S MANUAL PART IDENTIFICATION 2565-976_REV_A ● 03/2020 YETTER MANUFACTURING CO. Founded 1930 Colchester, IL 62326 Toll free: (800)447-5777. Fax: (309)776-3222 Website: yetterco.com E-mail: info@yetterco.com...
  • Page 2: Table Of Contents

    WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection.
  • Page 3: Safety Information

    BE ALERT! YOUR SAFETY IS INVOLVED WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION – BE ALERT!” It is your responsibility as an owner, operator, or supervision to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations.
  • Page 4 PLEASE READ, VERY IMPORTANT SECURE PLANTER FRAME AGAINST UNWANTED LOWERING BY APPLYING THE LOCKING MECHANISM ON THE HYDRAULIC CYLINDERS!
  • Page 5: Torque

    BOLT TORQUE Important: Over-tightening hardware can cause just as much damage as under-tightening. Tightening hardware beyond the recommended range can reduce its shock load capacity. All hardware on the 5500 Cover Crop Devastator is either Grade 5 or Grade 8, unless otherwise noted. Grade 5 cap screws are marked with three radial lines on the head.
  • Page 6: Assembly Instructions

    ASSEMBLY INSTRUCTIONS Step 1: Attach the 5000-167 torsion mount bracket to the frame using 4) M16 X 110 flange head bolts & 2) 5000-420 clamp straps. Thread the bolts into the clamp straps by hand & tighten to torque specifications. Note: Torque the M16 bolts @ 236 ft.
  • Page 7 ASSEMBLY INSTRUCTIONS Step 2: Install the 5000-292 Torsion Arm onto the Torsion Pivot Assembly & secure with the ¾” x 8” bolts & ¾” lock nuts. Step 3: Attach the roller mount to the pivot arms using the ½” x 2-1/2” x 3-1/2” U-bolts & lock nuts. NOTE: The bearing support tab on the roller mount tube should be on the backside of the bearing mount plate.
  • Page 8 ASSEMBLY INSTRUCTIONS Step 4: Install the Devastator roller, spacer and bearings to the roller tube using the ½” x 2-1/2” bolts and locknuts. IMPORTANT: The spacer must be installed between the roller and the bearing. The notches of the bearing housing must face the mounting plate. The extended race on the bearing will face toward from the roller.
  • Page 9: Part Identification

    PARTS IDENTIFICATION 5500-001 48 INCH COVER CROP ROLLER KIT ITEM PART NO. DESCRIPTION 2502-353 1/2-13 X 2 1/2HHCS GR8 ZP 2502-430 3/4-10 X 8 HHCS GR8, ZP 2502-805 M16 X 2 X 120 HEX FLANGE SCREW, THREADLOCK, ZP 2520-357 1/2-13 LOCK HEX NUT, GR A, ZP 2520-604 3/4-10 HEX TOP LOCK 2570-568...
  • Page 10 PARTS IDENTIFICATION 5500-002 60 INCH COVER CROP ROLLER KIT ITEM PART NO. DESCRIPTION 2502-353 1/2-13 X 2 1/2HHCS GR8 ZP 2502-430 3/4-10 X 8 HHCS GR8, ZP 2502-805 M16 X 2 X 120 HEX FLANGE SCREW, THREADLOCK, ZP 2520-357 1/2-13 LOCK HEX NUT, GR A, ZP 2520-604 3/4-10 HEX TOP LOCK 2570-568...
  • Page 11 PARTS IDENTIFICATION 5500-003 90 INCH COVER CROP ROLLER KIT ITEM PART NO. DESCRIPTION 2502-353 1/2-13 X 2 1/2HHCS GR8 ZP 2502-430 3/4-10 X 8 HHCS GR8, ZP 2502-805 M16 X 2 X 120 HEX FLANGE SCREW, THREADLOCK, ZP 2520-357 1/2-13 LOCK HEX NUT, GR A, ZP 2520-604 3/4-10 HEX TOP LOCK 2570-568...
  • Page 12 PARTS IDENTIFICATION 5500-031 SHORT MOUNT KIT...
  • Page 13 PARTS IDENTIFICATION 5500-032 LONG MOUNT KIT...
  • Page 14 NOTES...
  • Page 15 NOTES...
  • Page 16 2565-976_REV_A – 03/2020...

This manual is also suitable for:

5500-0015500-0025500-003