Advertisement
Quick Links
Advertisement
Related Manuals for PackshotCreator R3L Mark II
Summary of Contents for PackshotCreator R3L Mark II
- Page 1 PackshotCreator R3 Mark II QuickStart I N S T A L L A T I O N G U I D E...
- Page 2 1 USB cable covers © Sysnext. All rights reserved. This material is not to be interpreted as a guarantee of earnings and may not be copied, reproducved, modified, published, uploaded, posted or distributed in any way, without PackshotCreator’s prior consent.
-
Page 3: Specifications
PackshotCreator R3 Mark II SPECIFICATIONS PackshotCreator R3L Mark II PackshotCreator R3M Mark II Dimension (L x W x H): 115cm x 100cm x 123cm 100cm x 76cm x 97cm Maximum Target Size Top Shots: 51cm x 51cm 36cm x 36cm... -
Page 4: System Placement
PackshotCreator R3 Mark II SYSTEM PLACEMENT ROLLING THE UNIT: When all legs are up, roll the unit Use the #24 wrench to adjust leg Rotate the bottom nut to raise or into position. Lower the legs, height. Start by loosening the top lower the leg. - Page 5 PackshotCreator R3 Mark II SYSTEM PLACEMENT DISASSEMBLY: Remove 6 white hand screws, 3 on Unplug the 2 metal connectors. Unplug the power connector. each side. Slide the back light panel away The back light panel is very Once the 2 panels are separated,...
- Page 6 PackshotCreator R3 Mark II SYSTEM PLACEMENT PLACEMENT: Place the system on Place the system on the floor. Make Place the system on (Optional): (Optional): an PackshotCreator ErgoTable+ sure the system is level and legs an PackshotCreator ErgoTable (sold (sold separately).
-
Page 7: Hardware Installation
PackshotCreator R3 Mark II HARDWARE INSTALLATION ACRYLIC PANEL INSTALLATION 1/2: Remove the five white hand Remove the two white hand screws Remove the top light panel from screws. holding the top light panel to the the top by sliding it to the left and top. - Page 8 PackshotSpin Align the acrylic panels when the front door is detached. Note: O3T inside the PackshotCreator, so between the metal guide brackets Insert the acrylic panels between the power and USB cables can be on the top, before tightening.
- Page 9 PackshotCreator R3 Mark II HARDWARE INSTALLATION CABLE CONNECTION 1/2: String the top light power cable Plug one end of the power cable Plug one end of USB Type B cable through the ceiling hole. into the system and the other end into the system and the other end into a power socket.
- Page 10 PackshotCreator R3 Mark II HARDWARE INSTALLATION CABLE CONNECTION 2/2: Respectively, plug one end of the In this configuration, captured If you are using camera top shot, USB Type A cable into the left side images are saved to the memory...
-
Page 11: Component Replacement
PackshotCreator R3 Mark II CENTERING ARM (SOLD SEPARATELY) Plug in the power cable. Use a Phillips screwdriver to Attach the centering arm using 4 remove the 4 black screws. small black hand screws. PackshotCreator R3 Mark II COMPONENT REPL ACEMENT... - Page 12 PackshotCreator R3 Mark II COMPONENT REPL ACEMENT ACCESS AND REMOVE THE CORNER LAMP 1/2: Lift to remove both side walls and Unplug the studio and the top light Follow instructions from steps 01- front door. power cable. 04 in the “Acrylic Panel Installation”...
- Page 13 PackshotCreator R3 Mark II COMPONENT REPL ACEMENT ACCESS AND REMOVE THE CORNER LAMP 2/2: Then, tuck the connector and extra Lift to remove the column. When re-installing the Note: wire into the large hole. columns, be sure to align the screw with the small corner hole.
- Page 14 PackshotCreator R3 Mark II COMPONENT REPL ACEMENT ACCESS THE BACK LAMP: When re-installing Remove 2 small white hand screws Lift to remove the curved Note: the curved background, we and the holding bracket on the top background from the system with recommend to slide it down with of the curved background.
- Page 15 PackshotCreator R3 Mark II COMPONENT REPL ACEMENT LED LAMP REPLACEMENT: Use the same method to replace Disconnect the two wires by Use a Phillips screwdriver and the LED lamps on the corner. pressing the connector node while gently remove the LED lamps.