Gardena SILENO city Operator's Manual page 28

3.10.11 Frost Sensor
The grass is extra sensitive to wear if the yard is
Frost Sensor is activated, the
covered with frost. If the
product is not allowed to start to cut the grass if the
temperature is below 5° C / 41° F.
Note:
The frost sensor is located inside the chassis
and there can be a delay compared to the ambient
temperature.
3.10.11.1 To set the Frost Sensor
To get access to the menu on
1. Do steps 1–3 in
page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
> Frost Sensor .
3. Push the OK button to select
4. Push the BACK button.
3.10.12 General
In General you can change the general settings of the
product.
3.10.12.1 To set the time & date
To get access to the menu on
1. Do steps 1–3 in
page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Time & Date .
3. Use the arrow buttons to set the time and then
push the BACK button.
4. Use the arrow buttons to set the date and then
push the BACK button.
5. Use the arrow buttons to set the time format and
then push the BACK button.
6. Use the arrow buttons to set the date format and
then push the BACK button.
3.10.12.2 To set the language
To get access to the menu on
1. Do steps 1–3 in
page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Language.
3. Use the arrow buttons to select language and then
push the BACK button.
3.10.12.3 To set the country
To get access to the menu on
1. Do steps 1–3 in
page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Country.
3. Use the arrow buttons to select country and then
push the BACK button.
28 - Installation
3.10.12.4 To set the unit format
1.
2.
3.
3.10.12.5 To reset all user settings
1.
2.
Settings > Installation
3.
Frost Sensor .
4.
Note:
Messages, Date & Time, Language and Country
settings are not reset.
3.10.12.6 The About menu
The
for example serial number and firmware versions.
3.10.13 GARDENA smart system
Settings > General >
Only for smart SILENO city and smart SILENO life.
Note:
installed in the work area before you include it into the
GARDENA smart system app. Refer to
page 14 .
The product can connect to mobile devices that have the
GARDENA smart system app installed. The GARDENA
smart system makes it possible with wireless interaction
Settings > General > between your smart product and the GARDENA smart
system.
In the smart system menu in the product you can:
•
•
When the smart product is part of the smart system,
some menus in the product display are disabled. You
Settings > General >
can still see all of the settings in the product but some
can only be changed with the GARDENA smart system
Do steps 1–3 in To get access to the menu on
page 23 .
Use the arrow buttons and the OK button to move
Settings > General >
through the menu structure
Unit format.
Use the arrow buttons to select unit format and
then push the BACK button.
To get access to the menu on
Do steps 1–3 in
page 23 .
Use the arrow buttons and the OK button to move
Settings > General >
through the menu structure
Reset all user settings .
Use the right arrow button to select
reset of all user settings?
Push the OK button to reset all the user settings.
Security level, PIN code, Loop signal,
About menu displays information about the product,
Make sure that the smart product is fully
enable your smart product to include with or
exclude from the GARDENA smart system app.
check the status of the wireless connection to the
smart system.
1298 - 007 - 16.09.2020
Proceed with
Installation on