Gardena SILENO city Operator's Manual page 26

2. Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-3 .
3. Use the arrow button to select the area.
4. Push the OK button.
5. Measure the distance from the charging station to
the start of the area. Measure along the guide wire.
To measure the distance from the
Refer to
charging station on page 26 .
6. Push the arrow buttons to select the distance,
measured in m.
7. Push the OK button.
8. Use the arrow buttons to select the percentage of
the cutting time the product must cut the area. The
percentage is equal to the percentage of the area
in relation to the complete work area.
a) Measure the area.
b) Divide the measured area with the total work
area.
c) Convert the result to percentage.
Note:
The sum of Area 1-3 must be 100% or
less. If the sum is less than 100%, the product
sometimes straddles the guide wire and starts to
mow at the starting point. Refer to
page 27 .
9. Push the BACK button.
3.10.6.2 To set the CorridorCut function
Note:
To prevent that the grass in the narrow passage
is worn, GARDENA recommends to set a low
CorridorCut .
percentage for the
To get access to the menu on
1. Do steps 1–3 in
page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Coverage > Area 1-3 .
3. Use the arrow buttons to select the area.
4. Push the OK button.
5. Measure the distance from the charging station to
the beginning of the narrow passage. Measure
along the guide wire. Refer to
distance from the charging station on page 26 .
Note:
Make sure that the distance to the
CorridorCut is set inside the narrow passage.
6. Push the arrow buttons to select the distance.
7. Push the OK button.
8. Use the arrow buttons to select the % of the cutting
time that the product must start the narrow
passage cutting.
26 - Installation
9.
Settings > Lawn
10. Push the OK button to enable
11. Push the BACK button.
3.10.6.3 To do a test of the Lawn Coverage function
1.
2.
3.
4.
5.
6.
7.
3.10.6.4 To measure the distance from the charging
station
1.
2.
3.
Starting point on
4.
5.
6.
7.
8.
3.10.6.5 To disable or enable the Lawn Coverage
function
Settings > Lawn
Disable or enable the
area.
1.
2.
To measure the
3.
4.
3.10.6.6 To reset the Lawn Coverage settings
You can reset the
and use the factory setting.
1.
Use the arrow buttons and the OK button to select
More > CorridorCut .
Put the product in the charging station.
Do step 1-3 in To get access to the menu on page
23 .
Use the arrow buttons and the OK button to move
Settings > Lawn
through the menu structure
Coverage > Area 1-3 > More > Test .
Push the OK button.
Push the START button.
Close the hatch.
Make sure the product can find the area.
Put the product in the charging station.
To get access to the menu on
Do steps 1–3 in
page 23 .
Use the arrow buttons and the OK button to move
Settings > Lawn
through the menu structure
Coverage > Area 1-3 > How far?
Use the arrow buttons to set 500 m / 540 yd as a
distance.
Push the OK button.
Use the arrow buttons and the OK button to move
Settings > Lawn
through the menu structure
Coverage > Area 1-3 > More > Test .
Push the OK button.
Push the STOP button when the product is at the
distance you select to measure. The distance
shows in the display.
Lawn Coverage function for each
Do steps 1–3 in To get access to the menu on
page 23 .
Use the arrow buttons and the OK button to move
Settings > Lawn
through the menu structure
Coverage > Area 1-3 > Disable .
Push the OK button.
Push the BACK button.
Lawn Coverage settings for each area
To get access to the menu on
Do steps 1–3 in
page 23 .
1298 - 007 - 16.09.2020
CorridorCut .