Table of Contents
Advertisement
Quick Links
"TO BE REMOVED FOR USE BY THE OCCUPANT."
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
MADE IN THE U.S.A.
INSTALLATION, OPERATION, AND MAINTENANCE
If the carton shows sign of damage, inspect
the product before accepting and describe the
problem on the Bill of Lading.
INSPECTION
Inspect the unit prior to installation. In the event of a
problem, DO NOT install the unit.
All components are factory assembled to the bath and the
unit is water tested and inspected prior to leaving Jason
International, Inc.
NOTE: Transportation and insurance from Jason's
factory are the buyer's responsibility.
Damage sustained in transit is the responsibility of
the carrier. If damage is discovered, the carrier must
be immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier
to respond should be reported to the seller and carrier.
Always file a freight claim promptly.
The installer is responsible for insuring that the unit is
free from defects or shipping damage. In the event of a
problem, DO NOT install the unit.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
OWNER'S RECORD
Dealer:
Date Purchased:
Date Installed:
Installer:
Jason International, Inc. • 501.771.4477
Jason International, Inc. • 501.771.4477
OWNER'S MANUAL
AN-P Series Designer Freestanding Baths
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation.
EQUIPMENT ACCESS
In accordance with Building Codes, service access to
all hydrotherapy bath equipment, controls and electrical
connections must be provided during installation
(Recommended minimum 28" x 17" [71 x 43 cm]).
Insufficient access will hinder repair and maintenance.
Warranty service will not cover costs of providing
equipment access.
The Specification Sheet for this bath contains additional
technical information. This sheet can be provided by your
dealer or accessed online at www.jasoninternational.com.
PLACE SERIAL NUMBER CARD WITH
PRODUCT CONFIGURATION IN THIS BOX
Page 1 of 20
Page 1 of 18
49-1012-002
Date 07/2018
Customer Service : 800.255.5766
Customer Service : 800.255.5766
Copyright © 2018 Jason International, Inc.
Copyright © 2018 Jason International, Inc.
Advertisement
Table of Contents
Related Manuals for JASON Hydrotherapy Designer AN-P Series
Summary of Contents for JASON Hydrotherapy Designer AN-P Series
- Page 1 “TO BE REMOVED FOR USE BY THE OCCUPANT.” Jason International, Inc. 49-1012-002 8328 MacArthur Drive Date 07/2018 North Little Rock, AR 72118 www.jasoninternational.com MADE IN THE U.S.A. OWNER’S MANUAL AN-P Series Designer Freestanding Baths INSTALLATION, OPERATION, AND MAINTENANCE If the carton shows sign of damage, inspect ALL WARRANTY CLAIMS ON ACRYLIC SURFACE DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. This manual contains information and instructions for proper operation and maintenance of your therapy bath. Failure to follow these instructions could result in personal injury, electrical shock, or fire. WARNING: When using this unit, basic precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY DANGER: TO REDUCE THE RISK OF INJURY FOLLOW THESE PRECAUTIONS:... -
Page 3: Consignes De Sécurité Importantes
CONSIGNES DE SÉCURITÉ IMPORTANTES INSTRUCTIONS RELATIVES AU RISQUE DE FEU, CHOC ÉLECTRIQUE, OU DE BLESSURE. Ce manuel contient des informations et des instructions pour le bon fonctionnement et l’entretien de votre bain thérapeutique. Ne pas suivre ces instructions cela pourrait entraîner des blessures corporelles, un choc électrique ou un incendie. AVERTISSEMENT: Lors de l’utilisation de cet appareil, des précautions de base doivent toujours être suivies, y compris les suivantes: LIRE ET SUIVRE TOUTES LES INSTRUCTIONS ATTENTIVEMENT... - Page 4 Cautionary Warnings (English/French) ATTENTION: la temperature ambiante sous la baignoire où CAUTION: Ambient temperature under the bath where equip- l’équipement est installé ne doit pas dépasser 50°C. ment is installed must not exceed 122°F (50°C). AVERTISSEMENT : Toute modification de l’équipement n’est WARNING: Any modification to the equipment is not recom- pas recommandé...
- Page 5 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS INTRODUCTION FEATURES Jason offers the finest in soaking hydrotherapy baths but also offers the option for more hydrotherapy choices with This manual contains all of the information needed for Jason MicroSilk® or AirMasseur® therapy units. Please the proper installation and operation for your Jason bath.
- Page 6 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS (cont.) AIRMASSEUR FEATURES Standard Edition AirMasseur ® ® Jason’s AirMasseur hydrotherapy bath fills the bath with The Jason Standard Edition AirMasseur hydrotherapy in- millions of warm air bubbles to create a blanket of rolling cludes a variable-speed 1-HP air blower with heater, three movement, gently massaging your skin.
- Page 7 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS (cont.) STANDARD/PREMIER EDITION ELECTRONIC CONTROLS One main control touchpad mounted on the bath features several icons used by the bather to control the bath. This section will outline the functions of the system when a particular icon is pressed. If the icon is lit WHITE, then that particular option is available to operate.
- Page 8 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS (cont.) SIGNATURE EDITION ELECTRONIC CONTROLS AirMasseur [AM] ® MicroSilk [MS] ® ICONS AIRMASSEUR Icon Blower SPEED Icon LED Icon (Premier & Signature) MICROSILK Icon SIGNATURE EDITION OPERATING INSTRUCTIONS The Signature Edition digital touchpad mounted on the bath features an LCD readout which alternately indicates the water temperature (+/-5°F) and time remaining.
- Page 9 FEATURES, CONTROLS AND OPERATING INSTRUCTIONS (cont.) LED Icon AIRMASSEUR Icon ® The LED icon will operate the Chromatherapy The AIRMASSEUR icon is used to activate the Mood Lighting system. The LED system will operate blower and the 20-minute timer. for 2 hours before turning OFF. •...
-
Page 10: User Maintenance Instructions
USER MAINTENANCE INSTRUCTIONS HUMIDITY SURFACE MAINTENANCE Area with minor scratches or dull surfaces can be restored WARNING: Avoid high humidity levels in your home. by applying commercially available plastic polish (i.e. No- Mold, mildew, fungi and bacteria which may be harm- vus Plastic Polish No. -
Page 11: Installation Instructions
INSTALLATION INSTRUCTIONS INSTALLATION For AirMasseur baths, remove the blower with stand, ® check valve, tubing with (2) clamps and electronics Remove the product from its packaging. Read the entire from the separate blower carton. Set aside to be instructions prior to installing this product. installed later. - Page 12 INSTALLATION INSTRUCTIONS (cont.) Figure 3 8. Use the template to verify the four (4) locating stud holes on the bottom of the skirt. 9. After the finished floor is installed, position the installation template on the finished floor. Place the Floor template to line up with the existing floor drain location and orient the template to the desired position.
- Page 13 INSTALLATION INSTRUCTIONS (cont.) 19. If there is no access below the floor, use two 2x4 Optional Pedestal Skirt Ring Base boards to raise the bath above the floor and align the drain with the ‘P’ trap. Apply construction adhesive to the level form base and sealant to the ‘P’...
- Page 14 INSTALLATION INSTRUCTIONS (cont.) ELECTRICAL INSTALLATION These instructions are written assuming 60Hz, 120V power The pumps are supplied with an electrical bonding lug to supply. Verify the electrical requirements of the bath unit allow connection of a solid copper bonding conductor be- before installation.
- Page 15 INSTALLATION INSTRUCTIONS (cont.) REMOTE MOUNTING OF AIR BLOWER The Jason AirMasseur® system has been factory installed 5. Use screws to attach the pipe to the check valve and following ETL/UL Standard safety guidelines. During in- route the hose to the remote blower tubing floor cutout stallation, if remote mounting of the air blower is desired or location.
- Page 16 INSTALLATION INSTRUCTIONS (cont.) 3. Remove the two (2) decorative caps and screws on Htrvoe - Hthho akth the bottom sides of the cabinet and lift the cabinet off Phvutcn - aikuh akth the metal brackets and set it aside. See Figures 12 & Iru - Cncdl akth Fhekdcuhe 120W, 50 rt 60 I...
- Page 17 INSTALLATION INSTRUCTIONS (cont.) MICROSILK® [MS] SYSTEM Standard Edition Additional Options Available: Bluetooth Sound Immersion: (Included on Signature Edition) MS Pump Optional Bluetooth Sound Immersion Transducers installed on bath. Bluetooth amp supplied Keypad and field installed. [IDU-264] TRANSDUCER J S O N Ncmi Pinc Mloi Drooidvlro To Dedicated...
- Page 18 INSTALLATION INSTRUCTIONS (cont.) AIRMASSEUR® [AM] SYSTEM Standard Edition Additional Options Available: Bluetooth Sound Immersion: Cmrzis (Included on Signature Edition) Optional Bluetooth Sound Immersion Transducers installed on bath. Bluetooth amp supplied and field installed. Keypad [IDU-264] TRANSDUCER Ncmi Pinc J S O N Mloi Drooidvlro Prv Vtie To Dedicated...
-
Page 19: Troubleshooting Guide
TROUBLE SHOOTING GUIDE If you believe the unit to be within the warranty period, you must contact Jason Customer Service: 1-800-255-5766 with the bath’s Product and Serial numbers before work is started. These numbers can be found on the label on the front page of this manual and also adhered to the underside of the bath above the equipment. - Page 20 TROUBLE SHOOTING GUIDE AIRMASSEUR [AM] BLOWER SYSTEM ® SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION Air bath does not function properly a. Blower speed setting is set too low a. Change to a mid-range air speed while in Wave or Pulse mode. setting before switching over to Wave or Pulse modes.