Advertisement
Quick Links
INSTRUCTIONS
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
US Patent Pending
HVLP–Turbine Guns
10 psi (0.07 MPa, .7 bar) Maximum Inlet Air Pressure
50 psi (0.35 MPa, 3.5 bar) Maximum Inlet Fluid Pressure
Related Manuals
309205 – HVLP–Turbine Gun for maintenance and service instructions
309243 – HVLP Turbine
309244 – HVLP Compressor/Cart
Cup Feed
Includes 1-quart (1 liter) cup
Model 244113, without fluid set
Model 244117, with # 3 fluid set
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 2001, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
T10746
Remote Pressure Feed
Model 244115, without fluid set
Model 244118, with # 3 fluid set
309317
Rev. A
Advertisement
Related Manuals for Graco 244113
Summary of Contents for Graco 244113
- Page 1 Model 244113, without fluid set Model 244118, with # 3 fluid set Model 244117, with # 3 fluid set GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 ECOPYRIGHT 2001, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001...
- Page 2 ....... . Graco Phone Number ......
- Page 3 Fire and explosion hazard: Solvent and paint fumes can ignite or explode. D Sprayers generate sparks. Keep sprayer at least 20 feet (6 m) from explosive vapors. DUse in an extremely well ventilated area. DEliminate all ignition sources; such as pilot lights, cigarettes and static arcs from plastic drop cloths.
- Page 4 Component Identification Air flow control – Adjusts TOTAL Pattern Adjustment Knob – air flow to spray gun Adjusts pattern from fan to round Air cap/retaining ring – Adjusts fan direction Fluid flow/Pattern size control – Adjusts fluid volume Air inlet EasyGlidet Trigger Duckbill check valve Swivel tube and strainer...
- Page 5 PRESSURE RELIEF – Follow this procedure when cleaning, repairing or shuting down sprayer For Cup Guns Follow these instructions whenever 1. Turn off turbine. 2. Unlatch cup you stop spraying. 1. Turn off air supply to the pot. For Pressure Feed Guns 2 quart 2.
- Page 6 Use your hand to loosen and remove the air cap retaining ring and air cap housing. 2. Test spray pattern and atomization while holding gun about 6 to inches (150 to 200 mm) from test piece. While triggering the gun, use your hand to loosen and remove the nozzle. Use your hand to loosen and remove the fluid knob assembly and compression ring from the back of the gun and remove the old needle.
- Page 7 Setup Connect air hose to gun and turbine. For cup gun, turn fluid control out until trigger movement is not restricted. Caution: Turning knob too far will remove it. For remote pressure pot, hold gun parallel to floor and adjust fluid pressure to an 8 to 10 inch (203 to 254 mm) fluid stream.
- Page 8 Plug turbine power cord into a grounded outlet. SPRAY Open air control valve. Turn turbine on. Wait several minutes prior to spraying to allow warm–up time. Turn air cap to obtain desired direction. 309317...
- Page 9 Lock air cap with retaining ring. Nozzle Air cap Retaining ring Select spray pattern by adjusting the fluid knob and pattern selection knob. The air control ad- Round Pattern justs the TOTAL air to the pattern and gun. Set knob to RND air control Vertical Pattern Set knob to FAN...
- Page 10 To control over–spray, reduce air flow or reduce fluid volume. Note: If fluid is not atomizing properly, fluid may need to be thinned further, or a different tip size may be used. Swivel Tube Adjustment The adjustable swivel tube allows the HVLP–Turbine Gun to be held in any position why spraying. To adjust the position of the tube in the cup: 1.
- Page 11 Shutdown Cleaning the Spray Gun (solvent/oil–based) Close air valve. Perform Pressure Relief Procedure. Remove and empty cup. Add 1.5 inches of compatible cleaning solvent. Reinstall cup. Turn fan control to round spray pattern. 309317...
- Page 12 Turn air control valve to approximately half way. Trigger gun until solvent runs clean. Turn turbine off. Disconnect hose from gun. Perform Pressure Re- lief. Properly dispose of excess solvent. 309317...
- Page 13 Shutdown (water base) Turn turbine off. Perform Pressure Relief Procedure. Remove cup, empty and clean with soap and water. Remove air cap and nozzle and clean with water and brush. Clean fluid tube and nozzle housing with water and brush. 309317...
- Page 14 Parts for HVLP–Turbine Gun Model Nos. 244113, 244115, 244117, 244118 TI0745 309317...
- Page 15 LUBRICANT, grease (not 244124 FLUID SET shown) 197448 TOOL, wrench (not shown) NOZZLE, fluid NEEDLE ASSY *Not included on model 244113 or 244115. 244226 HOUSING, air cap †Not included on model 244115 or 244118. 188493 PACKING, u–cup, gun 196462 HANDLE, gun...
- Page 16 Technical Data Maximum inlet fluid pressure ........... . 50 psi (0.35 MPa, 3.5 bar) Maximum inlet air pressure .
- Page 17 Notes 309317...
- Page 18 TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you: 1–800–690–2894 Toll Free All written and visual data contained in this document reflect the latest product information available at the time of publication.