Smappee EV Wall Business Installation Manual
Hide thumbs
Also See for EV Wall Business:
- Installation manual (37 pages) ,
- Quick starter manual (13 pages) ,
- Quick install manual (2 pages)
Advertisement
Advertisement
Table of Contents
Related Manuals for Smappee EV Wall Business
Summary of Contents for Smappee EV Wall Business
- Page 1 Smappee EV Wall Business Installation manual English – Version 1.1 – March 2021...
-
Page 2: Table Of Contents
4. Components ....................7 5. Technical specifications................... 8 6. Preparing the installation ................9 7. Installation and activation ................12 8. Using the EV Wall Business ................23 9. Declaration of conformity ................27 Smappee EV Wall Business – Installation manual - English... -
Page 3: Introduction
This installation and user manual tells you how to install and use the Smappee EV Wall Business. We advise you to read the contents of this manual carefully, to ensure a safe and proper installation and enable you to use all the advanced features of this product to their full extent. -
Page 4: Safety Instructions
Safety warning Fully read and follow the safety instructions below before you install, service or use your Smappee EV Wall Business. The installer must ensure that the charging station is installed in accordance with the relevant national and local regulations. - Page 5 • Store the charging station in a dry environment within the temperature range specified in the technical specifications. Smappee EV Wall Business – Installation manual - English...
-
Page 6: Models
EV Wall Business White 3-Phase 22 kW Socket 5425036932166 EVWB-332-BR-E-B EV Wall Business Black 3-Phase 22 kW Socket EV Wall Business White 3-Phase 22 kW Type 2 cable 5425036932197 EVWB-332-C2R-E-W 2,5m EV Wall Business Black 3-Phase 22 kW Type 2 cable... -
Page 7: Components
3. 8 m version: 1 x EV cable holder + 3 x screws + 3 x plugs Identification label The identification label of your charging station is located on the left inside of the EV Wall Business. 1. Manufacturer 2. Article number 3. -
Page 8: Technical Specifications
Weight (excluding packaging) 6.2 kg 6.8 kg (2.5 m cable) or 9.8 kg (8 m cable) Charging cable length 1 x 2.5 m or 1 x 8 m Mounting method Wall Smappee EV Wall Business – Installation manual - English... -
Page 9: Preparing The Installation
Ethernet cable for the internet connection. • Make sure that there is at least 30 cm cable available at the location of the EV Wall Business to be able to connect it easily internally. The power supply enters the station at the bottom of the housing. - Page 10 The EV Wall Business requires a stable internet connection via Ethernet. An RJ-45 connector (not supplied) should be attached to the end of the cable. Only attach the RJ-45 connector after inserting the cable into the housing. The RJ-45 connector will not fit through the EV Wall Business’s cable gland! Prepare the mounting All Smappee EV Wall Business types are designed to be mounted on a wall.
- Page 11 3 x M4 x 6 mm HEX screws Supplies (not included) CAT 5/6 ethernet cable and RJ45 connector for internet access. Power supply cables Ferrules (10 mm²), for stranded power supply cables 32 A circuit breaker Smappee EV Wall Business – Installation manual - English...
-
Page 12: Installation And Activation
7. Installation and activation This procedure describes the required steps for the physical installation of the EV Wall Business. CAUTION: Make sure it is not possible to connect the electric current during installation. Put up caution tape and warning signs to mark the work areas. Make sure no unauthorised people can enter the work areas. - Page 13 Drill 3 holes of 10 mm diameter through the slots to a depth of 50 mm. Insert the supplied wall plugs into the holes. c. Attach the mounting plate to the wall with the supplied screws. Smappee EV Wall Business – Installation manual - English...
- Page 14 Remove the front plate of the EV Wall Business and disconnect the communication cables. Safely put aside the front plate to avoid damaging the PCB-board attached to it. b. Attach the EV Wall Business housing to the mounting plate using the three supplied M4 x 6 mm HEX screws.
- Page 15 Connect each supply cable to the differential. The protective earth should be connected to the terminal block. Tip: when using solid cables, use pliers to bend the cables into an ‘L’ shape before connecting these to the differential. Smappee EV Wall Business – Installation manual - English...
- Page 16 L3 – L1 – L2 – N And continue with this pattern for other EV Wall Business units. When phase rotation is applied on a connector, adjust the configuration in the Smappee Dashboard. Smappee EV Wall Business – Installation manual - English...
- Page 17 EV charging cable mounting (only fixed cable version) This section is only relevant if the EV Wall Business comes with a fixed cable. If you have a socket version, please continue to the next section. a. Mount the fixed charging cable through the left M32 cable gland and mount the power supply wires to the terminal block.
- Page 18 IMPORTANT notes for 3P (3*230V) – Delta topology When an EV Wall Business is installed in a residential installation with a 3P (3*230V) – Delta grid connection, some additional requirements need to be taken into account. These guidelines have nothing to do with the Smappee EV Wall Business architecture but linked to how the utility provides the grid connection to the home.
- Page 19 Be careful to connect the RJ10 cable to one of the B ports. Do not connect it to the A port. The Ethernet cable should be connected to the Smappee Connect, not to the PCB attached to the front plate.
- Page 20 Mount and tighten the supplied M4 nuts Smappee EV Wall Business – Installation manual - English...
- Page 21 All communication cables must be attached to the front panel before powering the EV Wall Business. The EV Wall Business should also be closed. a. Check all connections are secure and power-up the EV Wall Business. b. Check the status LEDs:...
- Page 22 The Smappee App will guide you through the various steps to fill in all the required information. • Log in to the Smappee App. If you would like to add this charging station to an existing location, log in with an account that has access to that location. If you would like to create a new location, you may create a new account.
-
Page 23: Using The Ev Wall Business
1. Plug and charge: Simply connect your cable and start charging. 2. Swipe and charge: Connect the cable, swipe your card and start charging. 3. Scan and charge: Connect the cable, scan the QR code in the Smappee app and start charging. - Page 24 Swipe and charge Charging sessions can be started using an RFID card. You can either use a Smappee Smart Charge Card for free charging or (if activated) a third party eMSP card to pay for charging sessions. • Free charging: charging is free with a Smappee Smart Charge Card or any other authorized RFID card.
- Page 25 Scan and charge The user pays by credit card (Visa or Mastercard) using the Smappee app. They scan the QR code shown on the charging station and the app will guide them through the process of starting the charging session. It is also possible to set discount rates for specific users. Please contact info@smappee.com...
- Page 26 The Smappee EV Wall Check the manual or contact Business is unavailable. your supplier for more info and further steps. Red flashing Your charge card is not Contact your charge card authorised. supplier. Smappee EV Wall Business – Installation manual - English...
-
Page 27: Declaration Of Conformity
Surge: EN 61000-4-5:2005 / EN 61000-4-5:2006 * Safety: Metering Function : IEC 61010-1 Ed 3.0 (2010-06) + A1:2016 AC Charging equipment : IEC 61851-1 (2017) / EN61558-1 Authorized signatory Stefan Grosjean Smappee EV Wall Business – Installation manual - English...
Need help?
Do you have a question about the EV Wall Business and is the answer not in the manual?
Questions and answers