Related Manuals for Epson S5U13742P00C100
Summary of Contents for Epson S5U13742P00C100
- Page 1 S1D13742 Mobile Graphics Engine S5U13742P00C100 Evaluation Board User Manual Document Number: X63A-G-002-01.1 Rev. 1.1...
- Page 2 This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any kind of damage and/or fire caused by the use of it.
-
Page 3: Table Of Contents
4.5.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board ..15 LCD Panel Interface ......16 GPIO Connections . - Page 4 Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
-
Page 5: Introduction
Board. The evaluation board is designed as an evaluation platform for the S1D13742 Mobile Graphics Engine. The S5U13742P00C100 evaluation board can be used with many native platforms via the host connector which provides the appropriate signals to support a variety of CPUs. The S5U13742P00C100 evaluation board can also connect to the S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. -
Page 6: Features
Features 2 Features The S5U13742P00C100 Evaluation Board includes the following features: • 121-pin FCBGA S1D13742 Mobile Graphics Engine • Header with all S1D13742 Host Bus Interface signals • Headers for connection to the S5U13U00P00C100 USB Adapter board • Headers for connecting to LCD panels •... -
Page 7: Installation And Configuration
PIOVDD output current = 2.5mA SW1-[4] not used = Required settings when using S5U13U00P00C100 USB Adapter board The following figure shows the location of DIP switch SW1 on the S5U13742P00C100 board. DIP Switch Figure 3-1: Configuration DIP Switch (SW1) Location... -
Page 8: Configuration Jumpers
Installation and Configuration 3.2 Configuration Jumpers The S5U13742P00C100 has 6 jumpers which configure various board settings. The jumper positions for each function are shown below. Jumper Function Position 1-2 Position 2-3 No Jumper COREVDD current COREVDD Normal — measurement PLLVDD current... - Page 9 1 and 2 of the jumper. The jumper associated with each power supply is as follows: JP1 for COREVDD JP2 for PLLVDD JP3 for IOVDD JP5 for PIOVDD Figure 3-2: Configuration Jumper Locations (JP1, JP2, JP3, JP5) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
- Page 10 When the jumper is at position 1-2, the IOVDD voltage must be provided to the H1 connector, pin 32. When the jumper is at position 2-3, the IOVDD voltage is provided by the 3.3V power supply of the board. Figure 3-3: Configuration Jumper Location (JP4) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
- Page 11 When the jumper is at position 1-2, the PIOVDD voltage must be provided to the H4 connector, pin 8. When the jumper is at position 2-3, the PIOVDD voltage is provided by the 3.3V power supply of the board. Figure 3-4: Configuration Jumper Location (JP6) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
-
Page 12: Technical Description
The green LED ‘3.3V Power’ is turned on when 3.3V power is applied to the board. 4.1.2 Voltage Regulators The S5U13742P00C100 evaluation board has an on-board linear regulator to provide the 1.5V power required by the S1D13742 Mobile Graphics Engine. It also has a step-up switching voltage regulator to generate adjustable 6~24V, which can be used to power the LED backlight on some LCD panels. -
Page 13: Clocks
The clock for the S1D13742 Mobile Graphics Engine is provided by a 4MHz oscillator. The S5U13742P00C100 evaluation board has a DIP14 footprint for an optional second oscillator, Y2. This is provided for cases requiring a different clock frequency for the S1D13742 Mobile Graphics Engine. -
Page 14: Host Interface
4.5.1 Direct Host Bus Interface Support All S1D13742 host interface pins are available on connector H1 which allows the S5U13742P00C100 evaluation board to be connected to a variety of development platforms. For detailed S1D13742 pin mapping, refer to the S1D13742 Hardware Functional Specification, document number X63A-A-001-xx. -
Page 15: Connecting To The Epson S5U13U00P00C100 Usb Adapter Board
When the S5U13742P00C100 is connected to the S5U13U00P00C100 USB Adapter board, there are 2 LEDs on S5U13742P00C100 which provide a quick visual status of the USB adapter. LED1 blinks to indicate that the USB adapter board is active. LED2 turns on to indicate that the USB has been enumerated by the PC. -
Page 16: Lcd Panel Interface
The following diagram shows the location of the LCD panel connectors H2 and H3. Figure 4-3: LCD Panel Connectors Location (H2, H3) For the pinout of connectors H2 and H3, see “Schematic Diagrams” on page 21. Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1... -
Page 17: Gpio Connections
4.7 GPIO Connections The S1D13742 Mobile Graphics Engine has 8 GPIO pins. All the GPIO pins are routed to the H4 connector. Note that connector H4 is not populated on the S5U13742P00C100 evaluation board. The following figure shows the location of the GPIO connector, H4. -
Page 18: Parts List
JP1, JP2, JP3, JP5 SIP2 2POS .100 TIN or GENERIC CONN HEADER VERT JP4, JP6 SIP3 3POS .100 TIN or GENERIC Steward HZ0603B751R-10 L1, L2 Ferrite R0603 FERRITE 200MA 938 OHMS 0603 SMD Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1... - Page 19 PITCH 4POS ITT Industries KSC241GLFS SW TACT-SPST SW_EVQQW SWITCH TACT SILVER PLT GULLWING Keystone 5015 TPGND1, TP3.3VDD1 TP_SMT TP_1206 PC TEST POINT MINIATURE SMT TP1, TP2, TP3, TP4 T POINT F SIP1 S1D13742 Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
- Page 20 TPS76915DBVT TPS76915DBVT SOT23-5 IC 1.5V 100MA LDO REG SOT-23-5 TI TPS61040DVBR TPS61040 SOT23-5 IC CONV DC/DC BOOST LP SOT-23-5 Connor-Winfield CWX823-4.0M 4M OSC OSC 4.0000MHz 3.3V 50ppm SMD 14-Pin DIP AMP 2-641609-1 Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
-
Page 21: Schematic Diagrams
Schematic Diagrams 6 Schematic Diagrams Figure 6-1: S5U13742P00C100 Schematics (1 of 3) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1... - Page 22 Schematic Diagrams Figure 6-2: S5U13742P00C100 Schematics (2 of 3) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
- Page 23 Schematic Diagrams Figure 6-3: S5U13742P00C100 Schematics (3 of 3) Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
-
Page 24: Board Layout
Board Layout 7 Board Layout Figure 7-1: S5U13742P00C100 Board Layout - Top View Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1... - Page 25 Board Layout Figure 7-2: S5U13742P00C100 Board Layout - Bottom View Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1...
-
Page 26: Change Record
• removed section 4.5.3 X63A-G-002-00 Revision 0.01 - Issued: June 25, 2007 • minor editing • section 5, added parts list • section 6, added schematics • section 7, added board layout Seiko Epson Corporation S5U13742P00C100 Evaluation Board Rev. 1.1... -
Page 27: Sales And Technical Support
Sales and Technical Support 9 Sales and Technical Support For more information on Epson Display Controllers, visit the Epson Global website. https://global.epson.com/products_and_drivers/semicon/products/display_controllers/ For Sales and Technical Support, contact the Epson representative for your region. https://global.epson.com/products_and_drivers/semicon/information/support.html Seiko Epson Corporation S5U13742P00C100 Evaluation Board...