Related Manuals for Epson S5U13709P00C100
Summary of Contents for Epson S5U13709P00C100
- Page 1 S1D13709 Embedded Memory Graphics LCD Controller S5U13709P00C100 Evaluation Board User Manual Rev.1.0 Document Number: XA8A-G-001-01.1 Rev.1.1...
- Page 2 2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to use it when any abnormal issue occurs even during proper and safe use.
-
Page 3: Table Of Contents
Hardware Reset ........................10 6. Parts List........................11 7. Schematic Diagrams ....................13 8. S5U13709P00C100 Board Layout ................17 9. Installation Guide for the S5U13U00P00C100 ............18 Installation and connecting ..................... 18 10. Using the panel I/F board ..................21 10.1 Connecting the panel I/F board .................... - Page 4 Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 5: Introduction
Introduction Introduction This manual describes the setup and operation of the S5U13709P00C100 Rev.1.0 Evaluation Board. This evaluation board is designed as an evaluation platform for the S1D13709 Embedded Memory Graphics LCD Controller. The S5U13709P00C100 Evaluation Board can be used with the USB Interface Board (S5U13U00P00C100), thus providing an easy connection to Personal Computer with a USB interface. -
Page 6: Features
Features Features The S5U13709P00C100 Evaluation Board includes the following features: • 80-pin TQFP14 S1D13709 Embedded Memory Graphics LCD Controller • 2.0mm pitch 40pin connector (x2) for USB Interface Board. (S5U13U00P00C100) • 2.54mm pitch 34pin connector (x2) for connecting other host interface. -
Page 7: Installations And Configuration
Installation and Configuration 3.1 Switches The S5U13709P00C100 Evaluation Board incorporates DIP switches (SW1, SW2), which allow configuration of the board. For switch locations on the evaluation board, see Figure 3-1: “Configuration DIP Switches Location”. Figure 3.1 Configuration DIP Switches (SW1), (SW2) Location... - Page 8 For 4bpp mode (REG[20h] bit 1-0 = 10) CNF1 CNF0 XSCL Cycle Time 16:1 32:1 64:1 Reserved When the TFT Interface is used (REG[34h] bit0 = 1), CNF[1:0] should be 00. = default setting Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 9: Configuration Jumpers
= default setting 3.2 Configuration Jumpers The S5U13709P00C100 Evaluation Board includes the following 2-pin, 3-pin and 8-pin jumper blocks which are used to control function and for power consumption measurement. For jumper locations on the evaluation board, see Figure 3-2: “Configuration Jumper Location”... - Page 10 Jumper Function Position1-2 No Jumper TPS61161A Enable Position3-4 No Jumper Vout = 20mA Position5-6 No Jumper Vout = 40mA ( and Position3-4) Position7-8 No Jumper Vout = 60mA (And position3-4/5-6) = default setting Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 11: Power Requirement
The S5U13709P00C100 Evaluation Board has an incorporated White LDE Driver Controller (TPS61161A) for the panel backlight. White LED Driver Controller drives the panel at a constant current. The S5U13709P00C100 Evaluation Board is possible to change the output current (20mA, 40mA, 60mA / Max 38V). Please set J1 with the specifications of the panel. -
Page 12: Connectors
Connectors Connectors The S5U13709P00C100 Evaluation Board has host interface connectors and panel interface connectors (P1, P2, H1, H2, H3 and H4). For connector locations on the evaluation board, see Figure 4-1: “Evaluation board Connector Location” Figure 4.1 Evaluation board Connector Location... -
Page 13: P1, P2 Host Interface Connector
LED too. This LED indicates that the 3.3V power is supplied. P1 and P2 connectors are 2mm pitch, dual row, and 40-pin female headers (20x2). Note: A windows driver must be installed on the PC when the S5U13709P00C100 is used with the S5U13U00P00C100 USB Interface Board. The S1D13xxxUSB driver is available at vdc.epson.com. H1, H2 Host Interface Connector When the S5U13709P00C100 Evaluation Board connects with the S5U13U00P00C100 USB Interface Board, H1 and H2 connectors can be used as monitor terminals. -
Page 14: Technical Descriptions
Clock source select The S5U13709P00C100 Evaluation Board has an on-board 24MHz oscillator (Y1) which drives the input with the internal oscillator circuit (XCG1). When not using the internal oscillator circuit, this board allows the usage of a variety of crystal oscillators with osc1 connectors (CLKI). The XCG1 source selection is determined with jumper on 1-2pin of JP8 and 1-2pin of JP11. -
Page 15: Parts List
R32, R33, R34 Resister 10 SH1, SH2, SH3, SH4, SH5, SH6, SH7, SH8, SH9, SH10, SH11, Short socket XJ8A-0211 OMRON SH12, SH13, SH14, SH15, SH16 DIP switch 219-12MST DIP switch 219-2MST Switch KSC241J C&K Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1) - Page 16 No. / Comments TP1, TP2, TP3 Monitor pin HK-2-S MAC8 T1, T2, T3, T4, T5, T6, Monitor TH S1D13709 EPSON Regulator LM1117MPX-3.3 LDE Driver TPS61161A TPS3801K33DCKR Power Supply Crystal FA-238 (24MHz) EPSON TOYOCOM Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 17: Schematic Diagrams
Schematic Diagrams Schematic Diagrams Figure 7.1 S5U13709P00C100 Schematics (1 of 4) Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1) - Page 18 Schematic Diagrams Figure 7.2 S5U13709P00C100 Schematics (2of 4) Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
- Page 19 Schematic Diagrams Figure 7.3 S5U13709P00C100 Schematics (3of 4) Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
- Page 20 Schematic Diagrams Figure 7.4 S5U13709P00C100 Schematics (4of 4) Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 21: S5U13709P00C100 Board Layout
S5U13709P00C100 Board Layout S5U13709P00C100 Board Layout Figure 8.1 S5U13709P00C100 Board Layout – Parts Side Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1) -
Page 22: Installation Guide For The S5U13U00P00C100
Installation Guide for the S5U13U00P00C100 Installation Guide for the S5U13U00P00C100 Installation and connecting The following instructions are for connecting the S5U13709P00C100 Evaluation Board to the S5U13U00P00C100 USB Interface Board. The S5U13U00P00C100 is not included with the S5U13709P00C100 kit. Figure 9.1 S5U13709P00C100 Evaluation Board Figure 9.2 S5U13U00P00C100 USB Interface Board... - Page 23 (2012-01-20)” from vdc.epson.com. 2. Install the driver onto your PC. 3. Connect P1 on the S5U13709P00C100 with P1 on the S5U13U00P00C100, and P2 on the S5U13709P00C100 with P2 on the S5U13U00P00C100. And connect to your panel with H3 and H4.
- Page 24 Installation Guide for the S5U13U00P00C100 4. Connect the 5V power supply adapter to the S5U13U00P00C100 and connect to the PC via USB. Figure 9.5 Connecting S5U13U00P00C100 Board, USB cable and 5V power adapter Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 25: Using The Panel I/F Board
Please refer to Figure 10.2 Panel I/F board and S5U13709 board. Connect H3 header of S5U13709 board and CN2 connecter of panel I/F board. Connect H4 header of S5U13709 board and CN3 connecter of panel I/F board. Figure 10.2 Panel I/F board and S5U13709 board Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1) - Page 26 Using the panel I/F board Figure 10.3 Panel I/F board schematic Seiko Epson Corporation S5U13709P00C100 Evaluation Board (Rev.1.1)
-
Page 27: Change Record
Revision 1.1 - Issued: April 09, 2018 • Reformat entire document • Updated address/contact page • Updated Epson web page and email address XA8A-G-001-01 Revision 1.0 - Issued: July 31, 2014 • Initial Release Seiko Epson Corporation S5U13709P00C100 Evaluation Board... -
Page 28: Sales And Technical Support
Sales and Technical Support 12. Sales and Technical Support For more information on Epson Display Controllers, visit the Epson Global website. https://global.epson.com/products_and_drivers/semicon/products/display_controllers/ For Sales and Technical Support, contact the Epson representative for your region. https://global.epson.com/products_and_drivers/semicon/information/support.html Seiko Epson Corporation S5U13709P00C100 Evaluation Board...