Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for turck NIC-M30 Series
Summary of Contents for turck NIC-M30 Series
- Page 1 Inductive Coupler Manual U S E R M A N U A L M A 1 0 0 8 Published 10/15/2014...
-
Page 2: Table Of Contents
Instructions for use - Inductive Coupler NIC...-M30 Contents About This Manual Target groups Explanation of symbols Feedback about these instructions Notes on the product Product identification Scope of delivery Standards and legal requirements 2.3.1 Classification of equipment acc. to SRD EN 300 440 Manufacturer and service For Your Safety Intended use... - Page 3 Maintenance Repair Decommissioning Returning the devices Specifications 14.1 Technical data of the primary side 14.2 Technical data of the secondary side 14.3 Technical data of inductive transfer system...
-
Page 4: Instructions For Use - Inductive Coupler Nic
TURCK accepts no liability for damage caused by failure to observe these instructions. If you require further information or have questions about the device, contact TURCK or visit our website. Target groups These instructions must be read and followed by anyone entrusted with any of the following tasks: ■... -
Page 5: Notes On The Product
Notes on the product Notes on the product Product identification Type code inductive coupler Type code – NIC…-M30 inductive coupler NIC P – M30 – IOL 2P8X H1141 – – Functional principle Component Design Functional principle Component Design NIC non-flush inductive coupler primary side (transmitter) M30 M30 x 1.5, threaded barrel secondary side (receiver) -
Page 6: Manufacturer And Service
The product is designed according to the latest state of the art technology. Residual hazards, however, still exist. Observe the following safety instructions in order to avoid hazards. TURCK accepts no liability for damage caused by failure to observe these safety instructions. -
Page 7: Product Description
Product description Product description Device overview Fig. 1: Left: Dimension drawing of NICP-M30-IOL2P8X-H1141; right: NICP-M30-8P8-0.3-RSC12T primary side, NICS-M30-IOL2P8-0.3-RKC4.4T secondary side The devices have a cylindrical housing style with an M30 × 1.5 male thread. An M12 connector (male) directly on the housing is used to connect the NICP-M30-IOL2P8X-H1141 primary side. The NICP-M30-8P8-0.3-RSC12T pri- mary side and the NICS-M30-IOL2P8-0.3-RKC4.4T secondary side are provided with a 0.3 m connection cable with an M12 female connector (pigtail). -
Page 8: Operating Principle
0.3/0.3 (ident no. U-73266) 2 standard PNP signals to the primary side. The junction box is not required if sensors with 2 PNP outputs (e.g. power clamps) are used. Fig. 3: Setup example for transferring 2 standard PNP signals Hans Turck GmbH & Co. KG •... -
Page 9: Io-Link Mode
Product description 4.3.2 IO-Link mode The devices NICP-M30-IOL2P8X-H1141 (primary) and NICS-M30-IOL2P8-0.3-RKC4.4T (secondary) are required for IO-Link mode. IO-Link mode provides a bidirectional IO-Link communication between an IO-Link master and an IO-Link device via the air interface. Fig. 4: Setup example for IO-Link communication 4.3.3 Transfer of 8 standard PNP signals To transfer 8 standard PNP signals, the following devices are required:... -
Page 10: Accessories
(chapter 5.1), “Power with lateral offset” (chapter 5.2) and “Distance between primary side and secondary side” (chapter 5.3). Fit the device at the intended mounting location. Observe the minimum mounting distances. ➤ ➤ Hans Turck GmbH & Co. KG •... -
Page 11: Power With Angle Offset
Mounting Distance 60 mm 26.5 mm 30 mm 60 mm Fig. 6: Mounting distances Power with angle offset α Distance D Angle α Power 2 mm 7.5° 12 W 4 mm 15° 12 W 5 mm 20° 12 W 7 mm 25° 12 W 8 mm 30° 1 W Fig. 7: Angle offset Power with lateral offset Distance D Offset M Power... -
Page 12: Connecting
2 n.c. 1 BN 3 BU 3 GND – Contact 3 4 Input 1 & C/Q (IO-Link) 4 BK Contact 4 Input 1 & C/Q (IO-Link) Fig. 13: Terminal layout Secondary side Hans Turck GmbH & Co. KG •... -
Page 13: Transfer Of 8 Standard Pnp Signals
Commissioning Transfer of 8 standard PNP signals Connect the sensors to the respective ports of the I/O hub for IO-Link TBIL-M1-16DIP (Ident no. 6814100). Use ➤ ➤ here channel A (contact 4). Connect the secondary side NICS-M30-IOL2P8-0.3-RKC4.4T as per the terminal layout in Fig. 15 to the TBIL-M1- ➤... -
Page 14: Rectifying Device Faults
(e.g. chips) in order to improve operation. Repair The device must not be repaired by the user. If the device is faulty, decommission it and send it to TURCK. Observe here the specific warranty conditions agreed with the shipment. - Page 15 Specifications 14.2 Technical data of the secondary side Specifications NICS-M30-IOL2P8-0,3-RKC4.4T Output voltage 24 VDC ± 10 % Output function 4-wire PNP and IO-Link Ambient temperature -20…+55 °C Degree of protection IP67 and IP68 Output current 500 mA Peak current output 2400 mA for 0.1 ms Start time 10 ms Electrical connection...
Need help?
Do you have a question about the NIC-M30 Series and is the answer not in the manual?
Questions and answers