Rear Exit - Continental Fireplaces Builder Series Installation Manual

Example:
V = 1.5 FT (0.5m)
1
V = 5 FT (1.5m)
2
V = V + V = 1.5FT (0.5m)+ 5FT (1.5m) = 6.5 FT (2m)
T 1 2
H = 1 FT (0.3m)
1
H = 1 FT (0.3m)
2
H = 10.75 FT (3.3m)
3
H = H + H + H = 1FT (0.3m) + 1FT (0.3m) + 10.75FT (3.3m) = 12.75FT (3.9m)
R 1 2 3
H = .03 (three 90° elbows + one 45° elbow - 90°)
O
= .03 (270° + 45° - 90°) = 6.75 FT (2.1m)
H = H + H = 12.75FT (3.9m) + 6.75FT (2.1m) = 19.5 FT (5.9m)
T R O
H + V = 19.5FT (5.9m) + 6.5FT (2m) = 26 FT (7.9m)
T T
Formula 1:
H < 3 V
T T
3 V = 3FT (0.9m) x 6.5FT (2m) = 19.5FT (5.9m)
T
19.5FT (5.9m) = 19.5FT (5.9m)
Formula 2:
H + V < 40 FT (12.2m)
T T
26 FT (7.9m) < 40 FT (12.2m)
Since both formulas are met, this vent configuration is acceptable.
2.10

rear exit

WARNING
!
f i r e - p a r t s . c o m
• Failure to create a seal to the fi rebox with the exhaust collar assembly will cause the appliance to function
improperly and can cause injury or property damage.
A.
Remove the safety barrier and glass front, refer to "safety
barrier & door removal/installation" section.
B.
Remove the contents from the fi rebox and set aside, you will
need the exhaust fl ue collar from the top of the log carton.
C.
To ease assembly, remove the four hex head screws
securing the defl ector from inside the top front of the fi rebox,
refer to Figure 1.
D.
Place the gasket (provided) over the 4" (102mm) fl ue collar
assembly and bend along perforation.
E.
From inside the fi rebox, insert the 4" (102mm) fl ue collar through the back
of the fi rebox. Install the rear exit shield onto the 4" (102mm) fl ue collar, see
"rear exit shield" section for installation instructions.
F.
Secure the fl ue collar assembly, gasket and rear exit shield using the four hex
head 3/8" thread cutting screws, refer to Figure 2.
note:
Do not overtighten. The gasket needs only to be
snug against the fi rebox.
G.
Reattach the defl ector using the four screws and install the log set, glass
door and safety barrier.
H.
Install the 7" collar assembly, complete with
gasket, onto the rear panel around the 4"
(101.6mm) collar with the screws provided (FIG 3).
venting requirements
90°
H
2
45°
V
1
H
1
90°
Fig. 1
DEFLECTOR
É
V
2
90°
H
3
Fig. 2
Fig. 3
GASKET
INTAKE COLLAR
ASSEMBLY
W415-1850 / A / 03.06.19
EN
23