Draper FlexShade D MO Series Installation & Operation Instructions
Draper FlexShade D MO Series Installation & Operation Instructions

Draper FlexShade D MO Series Installation & Operation Instructions

Dual roller coupled motorized

Advertisement

Quick Links

Dual Roller Coupled
Motorized FlexShades

Overview - Components

FLEXSHADE D*MO
Locking
Ring
I d l e
r E n
B r a
d
c k e
t
Read and understand all warnings
Contents
Overview - Components .......................................................................................1
Section 1 - Mounting Brackets ...........................................................................3
Section 2 - Idler-End and Operator End Assemblies ......................................3
Section 3 - Pocket Headbox Installation ...........................................................4
®
(Large Hardware)
Motor
Plate
S p
a n
W r
n e
e n
r
c h
CAUTION
before beginning installation.
(Page 2 of this document)
Section 4 - Installing Closure Panel ...................................................................5
Section 6 - Fabric/Roller Assembly Alignment ................................................8
Section 8 - Electrical Connections ............................................................... 9-11
Section 9 - Dimensions ......................................................................................12
Section 10 - Large Hardware Dimensions ......................................................12
© 2021 All Rights Reserved
INSTRUCTIONS
INSTALLATION & OPERATION
M o
t o r
B r a
E n d
c k e
t
PERSONNEL
REQUIRED
..........................................................................................6
If you have any difficulties installing or servicing your
Dual Roller Coupled FlexShades
, call your dealer or Draper, Inc.
®
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: Coupled_DR_FS_MO_Large_Hardware_Inst21
TOOLS
REQUIRED
PENCIL
POWER DRILL
TAPE MEASURE
LEVEL
HARDWARE
(by others)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FlexShade D MO Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Draper FlexShade D MO Series

  • Page 1: Table Of Contents

    If you have any difficulties installing or servicing your Dual Roller Coupled FlexShades , call your dealer or Draper, Inc. ® Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: Coupled_DR_FS_MO_Large_Hardware_Inst21 © 2021 All Rights Reserved...
  • Page 2: Please Read - Important Safety And Installation Information

    Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush If the shade is telescoping, place a piece of high attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy quality gaffer tape about 1"...
  • Page 3: Section 1 - Mounting Brackets

    Dual Roller Coupled Motorized FlexShades page 3 of 12 ® (Large Hardware) Section 1 - Mounting Brackets Figure 1 Retainer Clip Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. 1. Mark wall, jamb, or ceiling for placement of mounting brackets. 2.
  • Page 4: Section 3 - Pocket Headbox Installation

    Dual Roller Coupled Motorized FlexShades page 4 of 12 ® (Large Hardware) Section 3 - Pocket Headbox Installation Figure 3-A PLEASE NOTE: Installer must provide adequate clearance for removal of Roller Assembly during installation and maintenance. PLEASE NOTE: Headbox must be mounted directly to ceiling, or to a continuous blocking that is secured to building structure.
  • Page 5: Section 4 - Installing Closure Panel

    Dual Roller Coupled Motorized FlexShades page 5 of 12 ® (Large Hardware) Figure 3-E 165mm Brackets Mounted to Continuous Blocking Secured to (by others) 60mm 38mm Building Structure 59mm 216mm WALL Continuous 86mm Blocking (by others) Wall Clip (pre-attached to headbox) 1.6mm 22mm 3"...
  • Page 6: Section 5 - Mounting / Assembly

    "Operating the Retractable Coupler Shaft" section below. Caution: All motors should be tested and limits set using test cord before electrician wires shade. Please Note: Custom products/installations may not be reflected by this document. Call Draper, Inc. with any questions about product installation.
  • Page 7 Dual Roller Coupled Motorized FlexShades page 7 of 12 ® (Large Hardware) Section 5.4 - Intermediate Fabric/Roller Assembly (Fig. 8) Please Note: Skip this section if your unit only has two panels 1. If desired, the proper location of the next bracket can be verified. Otherwise, proceed to step 2. 2.
  • Page 8: Section 6 - Fabric/Roller Assembly Alignment

    Dual Roller Coupled Motorized FlexShades page 8 of 12 ® (Large Hardware) Section 6 - Fabric/Roller Assembly Alignment (Steps are shown for right-hand operators) Please note: If needed, the fabric panel heights can be adjusted so that the bottom 5. Tighten the locking ring by firmly rotating it approximately ¼ turn edges of the fabric panels are aligned.
  • Page 9: Section 8 - Electrical Connections

    All operating switches should be “off” before power is connected. Please Note: For low-voltage wiring requirements, Draper recommends consulting with a professional low-voltage electrical contractor. It is very important that shielded and stranded CAT 5 cable be used to prevent any electrical interference.
  • Page 10 Standard Do not wire motors in parallel without Connector M12 Connector written permission from Draper. 1 - BLACK 2 - WHITE 2 - WHITE 2 - WHITE Telis 1 Ø...
  • Page 11 Dual Roller Coupled Motorized FlexShades page 11 of 12 ® (Large Hardware) Overview Controls & System Overview C Motors 120VAC Motors AV Gateway Contact Contact Closure Closure Handheld Interface Interface Remote Wireless Network Network Network Device Connector Device Connector Device Connector Gateway Network Network...
  • Page 12: Section 9 - Dimensions

    (33 mm) (33 mm) " " (21 mm) (21 mm) * This number may be greater, depending on motor selection. Contact Draper for motor verification. Section 10 - Large Hardware Dimensions 165mm Large Dual Roller Pocket Headbox Dimensions 60mm 38mm SHADE WIDTH 2.4mm...

Table of Contents