Draper FlexShade Installation & Operation Instructions
Draper FlexShade Installation & Operation Instructions

Draper FlexShade Installation & Operation Instructions

Rechargeable motorized window shade with no wiring or electrician needed

Advertisement

FlexShade
®
Rechargeable motorized window shade with no wiring or electrician needed

Overview - Components

FLEX RECHARGE
T O P
s a l
v e r
i n g
U n i
u n t
t
I d l e
c k e
M o
c a p
B r a
E n d
e r
C o v
c a p
E n d
TOOLS REQUIRED
TAPE MEASURE
PENCIL
Contents
Overview - Components .......................................................................................1
Section 1 - Brackets .............................................................................................3
Section 2 - Endcaps ..............................................................................................3
Section 3 - Fascia ..................................................................................................3
Section 4 - Headbox..............................................................................................4
Recharge
E R
C O V
C K
/ B A
H E A
K E T
P O C
r
v e
D r i
E F
C l i p
A D
H E
S H
LEVEL
POWER DRILL
PLIERS
X
D B O
B E
T U
M O
C
R I
A B
t o r
M o
r
p t o
A d a
v e
D r i
r
p t o
R
A d a
B A
M
I A
S C
F A
HARDWARE
(by others)
Section 5 - Charging Options ..............................................................................4
Section 6 - Remote Controller ............................................................................5
Section 7 - 12 Volt Motor Initial Setup ................................................................5
Section 8 - 12 Volt Motor Limits ..........................................................................6
Section 9 - 5 Volt Motor Initial Setup..................................................................7
Section 10 - 5 Volt Motor Limits ..........................................................................8
Section 11 - Dimensions .....................................................................................11
INSTRUCTIONS
INSTALLATION & OPERATION
U n i
M o
r
p t o
A d a
s
e w
S c r
t o r
M o
t e
P l a
R
T O
CAUTION
Read and understand
all warnings before
beginning installation.
If you have any difficulties installing or servicing your
FlexShade Recharge, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: FS_MO_Recharge_Inst21
© 2021 All Rights Reserved
c a p
E n d
e r
C o v
s a l
v e r
i n g
u n t
t
c k e
B r a
c a p
E n d
PERSONNEL
REQUIRED
1
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FlexShade and is the answer not in the manual?

Questions and answers

Summary of Contents for Draper FlexShade

  • Page 1: Table Of Contents

    Section 11 - Dimensions ..................11 If you have any difficulties installing or servicing your FlexShade Recharge, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: FS_MO_Recharge_Inst21 © 2021 All Rights Reserved...
  • Page 2: Please Read - Important Safety And Installation Information

    Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy If the shade is telescoping, place a piece of shimming water.
  • Page 3: Section 1 - Brackets

    (Fig. 4) Large Figure 3 Figure 1a 2 x 2 2 " (73mm x 56mm) 57mm Figure 4 - FLEXSHADE RECHARGE ENDCAP DIMENSIONS " 2 " 17mm 73mm 3 " 3 " 2" 2" (83 mm) (83 mm)
  • Page 4: Section 4 - Headbox

    FlexShade Recharge ® page 4 of 11 Section 4 - Headbox STEP 1 Caution: Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at correct width. STEP 2 Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
  • Page 5: Section 6 - Remote Controller

    LCD displays “U” when unlocked LED blinking when unlocked Exiting Sleep Mode FlexShade Recharge battery motors do not come preprogrammed from Draper unless specified on order. Upon leaving factory each motor is placed into “Sleep ® Mode” to avoid accidental operation during shipping. It is necessary to “Wake” motor before operation and setup.
  • Page 6: Section 8 - 12 Volt Motor Limits

    FlexShade Recharge ® page 6 of 11 Section 8 - 12 Volt Motor Limits Move shade to desired Important: After highest or lowest setting limits, motor To save upper limit, To save lower limit, position by pressing will automatically hold both UP and STOP.
  • Page 7: Section 9 - 5 Volt Motor Initial Setup

    FlexShade Recharge ® page 7 of 11 Section 9 - 5 Volt Motor Initial Setup 15 Channel Remote Press right button for 1 second or less to display current mode. Select channel Hold P1 button on Hold STOP on on controller.
  • Page 8: Section 10 - 5 Volt Motor Limits

    FlexShade Recharge ® page 8 of 11 Section 10 - 5 Volt Motor Limits To reverse shade direction, hold both UP and DOWN until the motor responds. IMPORTANT Cycle shade up and down prior to setting limits IMPORTANT to settle fabric.
  • Page 9 FlexShade Recharge ® page 9 of 11 FAVORITE POSITIONING Setting 5 Volt Favorite Position Deleting 5 Volt Favorite Position Set a favorite position Send Shade to Press P2 on Favorite Position controller. Move shade to the desired position by pressing...
  • Page 10 FlexShade Recharge ® page 10 of 11 5V Motor Stop Configuration Turn Soft Stop OFF: Turn Soft Stop ON: Motor must be in slowest speed to turn Soft Stop OFF. Motor must be in fastest speed to turn Soft Stop ON.
  • Page 11: Section 11 - Dimensions

    FlexShade Recharge ® page 11 of 11 Section 11 - Dimensions Small Endcap Large Endcap 3 " 2" (83 mm) (51 mm) " " (17.5 mm) (16 mm) 1 " 2 " (48 mm) (57 mm) 2 " 3 "...

Table of Contents