Specifications - BMS DLC50 Installation & Operation Manual

6 SPECIFICATIONS

Products Controlled:
Operating Temp:
Dimensions:
Weight:
Panel Fasteners:
System Control:
TX Control:
RF Power:
LEDs:
Backlight for panel text:
Display:
Reports to display:
Encryption/Scrambling:
Presets:
DLC50 presets:
TX presets:
RX presets:
Expert menu groups:
Simple menu:
Hot keys:
Menu Navigation:
Panel Dimming:
Connectors Rear:
Connectors Front:
Serial port interfaces:
Operating Voltage:
Power Consumption:
Electrical Compliance:
Supplied Accessories:
The document reference is online, please check the correspondence between the online documentation and the printed version.
DLC50 Control Panel Installation and Operation Manual | Doc. No. 6051439500 Rev. A
CCII-(x)LP, BPA-(x), all CTxxxx exciters and PA's
-20 to +60 deg. C (MIL STD 810)
1.47" H x 5.72" W x 4.07" D (less connectors)
≤ 1.0 lb.
"Dzus" type, 2 places, color black, level with front of panel; dimensions and fastener
locations conform to MIL-SPEC MS25212C
On/Off Toggle Switch controlling system power (control signal)
Dedicated TXEN key. Status is shown on bottom line of display above TXEN key.
Menu selection, or hot-key (user selectable).
a. ALM – Yellow (green in NVIS versions) summary alarm (details listed on second line
of display)
b. Actuator Up – Green (stowed)
c. Actuator Down – Yellow (deployed) (green in NVIS versions)
Always on (green)
OLED; Graphical and 3-lines of text. Top line is double size.
Faults: Loss of frequency lock (transmitter automatically enters standby mode)
TX serial com
RX serial com
TX Fault (general Transmitter fault)
Loss of input signal (on equipped transmitters)
Dependent on transmitter, options, and licenses, AES, BISS, BMS-4, BMS-6 supported
Supports 3 types of presets: (20) DLC50 presets, Transmitter presets (number depends
on transmitter model), and Receiver presets (number depends on receiver model)
Stores and recalls up to 20 user definable presets - Can store TX frequency, TX
channel, TX frequency, or TX preset, TX power level, Encryption state and key index,
RX frequency, RX channel, RX preset, decryption state and key index, Relay states
(only for manual configured relays).
Supports recall of up to 99 TX presets. Number and contents of TX presets are
dependent on TX model.
Supports recall of up to 99 RX presets. Number and contents of RX presets are
dependent on RX model.
DLC50 presets, TX, RX, Other, Configuration.
User selectable. Can contain: DLC preset, TX frequency, TX channel, TX preset, TX
power level, Encryption, RX frequency, RX channel, RX channel, RX preset,
Decryption, relay control
User Selectable. Can be defined as any of the following: DLC50 preset menu, DLC50
preset, TX frequency menu, TX channel menu, TX channel, TX preset menu, TX
preset, TX power level, RX channel menu, RX frequency menu, RX preset menu,
Encryption on/off, Encryption menu, Decryption on/off, decryption menu, relay 1 toggle,
relay 2 toggle, relay 3 toggle, relay 4 toggle, Dim control menu. .
Dual rotary encoder with integral push-button. Keypad keys also function as OK,
Cancel, and Exit.
External Linear fade 0-28VDC, and manual trim/override.
I/O – DB25-S
Actuator control - PTO2E-10-98S
Power in - PTO2E-12-4P
USB - USB-A (host),
Remote Serial Port (service port) - 2.5mm stereo audio female
(3) RS-232
24-32 VDC
<0.1A normal, <1.0A when using antenna actuator
RTCA DO-160, EN2282, MIL-STD-704
All mating connectors.
All Operation and Installation Manuals.
Broadcast Microwave Services 25