Advertisement
CHOOSING THE APPROPRIATE EQUIPMENT CONTINUED...
In addition, the materials used in these hoods are not suitable for use in high
temperature applications, like fire fighting. Exposure to high ambient tem-
peratures above 150° F / 65° C may cause the protective materials to fail.
The respiratory protection program must also take into consideration the
levels of exposure which may be hazardous irrespective of respiratory pro-
tection (e.g.: contaminants which are toxic through exposure to unprotected
skin). Additional protective equipment such as apparel may be required.
However, any additional protective equipment must not interfere with ac-
cess to or operation of the respirator.
When properly attached to a SCOTT PROFLOW 3 respirator, the PROFLOW
FH22 Hood provides limited protection from airborne contaminants to only
the head, neck, throat, and upper chest areas of the user. The using em-
ployer or agency must provide the appropriate protective clothing for use
with this equipment and must insure that protective clothing will not interfere
with the operation of the respirator or the hood. The user must insure that
the PROFLOW FH22 Hood, the PROFLOW 3 respirator and the protective
clothing are properly donned and operating correctly. Do not wear any other
head gear over or under the PROFLOW FH22 Hood.
This equipment is not intended for use in atmospheres which are or may
become IMMEDIATELY DANGEROUS TO LIFE OR HEALTH (IDLH), in HIGH
TEMPERATURE ENVIRONMENTS, or in ATMOSPHERES WHERE THE
IDENTITY AND/OR CONCENTRATION OF THE CONTAMINANT IS UN-
KNOWN. This equipment is only for use in atmospheres from which the
user may safely escape without the use of the respirator.
This hood is intended only for a single use and disposal after use, for ex-
ample, after a single shift of work. Choosing to clean and re-use this hood is
at the discretion and risk of the user and the respiratory protection program.
REGULAR OPERATIONAL INSPECTION
The PROFLOW FH22 Hood must be inspected when first received and before
each use of the PROFLOW FH22 Hood with the respirator. If the PROFLOW
FH22 Hood is stored for emergency use, it must be inspected regularly. If any
discrepancies are found, remove the PROFLOW FH22 Hood from service and
tag for repair or replacement as required. Inspect as follows:
1. Inspect the PROFLOW FH22 Hood for any holes or tears in the fabric.
2. Verify that all seams and joints are secure and show no signs of weakening
or breakdown.
3. If not already removed, remove the protective paper from the front of the
visor window.
4. Check the visor window for cracks and damage to the perimeter seal. Check
the visor window for scratches which might interfere with visibility.
5. Check the exhalation port and channels to make sure there is no damage
that would interfere with the movement of exhaled air.
6. Verify that the inner elastic head band is secure and that the elastic head
size adjustment cord and cord lock are operating properly.
7. Check the neck cord and the cord lock for completeness and operation.
Check the neck cord channel for tears in the seams.
8. Check the attachment of the breathing tube to the hood. Verify that the
washer is in place and that the fabric is flat and not wrinkled. Verify that the
nut is hand tight.
9. Inspect the breathing tube for any damage including holes in the side wall,
crushed internal coil, or separation of either end. If any damage is found,
replace the breathing tube before use of the respirator.
10. Inspect the gasket inside of the female end of the breathing tube. Do not
use the breathing tube with a missing or damaged gasket. Remove the
breathing tube from service and tag for repair by authorized personnel.
If any damage or discrepancies are found, remove the PROFLOW FH22 Hood
from service and tag for disposal and replacement.
P/N 595141-01 Rev A 7/08
THE PROFLOW FH22 HOOD IS NOT IN-
TENDED FOR USE IN FIRE FIGHTING OR
OTHER HIGH TEMPERATURE OPERA-
TIONS
TEMPERATURE COULD BE ABOVE 150°
F / 65° C. USE OF THE PROFLOW FH22
HOOD IN HIGH TEMPERATURES MAY
RESULT IN FAILURE OF THE PROTEC-
TIVE MATERIAL, EXPOSING THE USER
TO THE HAZARDOUS ENVIRONMENT
RESULTING IN BURNS, SERIOUS IN-
JURY OR DEATH.
4
WARNING
WHERE
THE
AMBIENT
Advertisement
