Digitax F3 Plus Technical Manual page 40

Nr. Functions
309 Must the MES (Multi-Extra Charge System) be enabled?
310 Distance to enable registration or ForHire: this is the distance that enables either the registration of the black fare with a passenger aboard in Stopped or the automatic
activation of Hired. See Q.313. The distance is given in metres with an accuracy of 0.1 meter. The allowed value goes from 0.0 (min) to 6553.5 (max). The digit indicating
multiples of 0.1 m (so at the right of the decimal point) will flash.
311 IR-sensor for passenger-det. is present? - Is the Infra-Red-sensor for the detection of passengers present?
The allowed answer is either:
312 IR-sensor contact is normally closed? - Is the Infra-Red-sensor contact a Normally Closed contact ? If not, then it is a Normally Open contact.
The allowed answer is either:
313 Black fare registr. or autom. in Hired? - After the distance programmed in Q.310 should be activated either: the registration in memory of the black fare with a
passenger aboard in Stopped or the automatic activation of Hired? The allowed answer is either: 0 (No: registration) or: 1 (Yes: pass to Hired).
314 Block taximeter if fare-memory is full? - Should the taximeter be blocked when the fare-memory is full?
The allowed answer is either:
The ForHire led flashes if IR-sensor is ON? - When the IR-sensor is activated should the ForHire led flash?
315
The allowed answer is either:
319 Inhibit visualization memory-block n. 1? - Should it be impossible to visualize memory-block number 1? See also Q.320.
The allowed answer is either:
320 Enable visualization MB1 with password? - If the visualization of memory-block number 1 has been inhibited (see Q.319) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
321 Inhibit printing memory-block n. 1? - Should it be impossible to print memory-block number 1? See also Q.322.
The allowed answer is either:
322 Enable printing MB1 with password? - If the printing of memory-block number 1 has been inhibited (see Q.321) should it be possible to undo this with the password? The
allowed answer is either:
323 Inhibit reset of memory-block n. 1? - Should it be impossible to reset memory-block number 1 from panel? See also Q.324.
The allowed answer is either:
324 Enable reset of MB1 with password? - If the reset from panel of memory-block number 1 has been inhibited (see Q.323) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
325 Inhibit access to stat. Memory n. 1? - Should it be impossible to have access to the reading-procedure of the statistics-memory number 1?
The allowed answer is either:
326 Programming only with the memory-key? - Should programming only be possible with the memory-key? If not, then programming is also possible step by step. The
allowed answer is either:
327 Inhibit visualization memory-block n. 2? - Should it be impossible to visualize memory-block number 2? See also Q.328.
The allowed answer is either:
328 Enable visualization MB2 with password? - If the visualization of memory-block number 2 has been inhibited (see Q.327) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
329 Inhibit printing memory-block n. 2? - Should it be impossible to print memory-block number 2? See also Q.330.
The allowed answer is either:
330 Enable printing MB2 with password ? - If the printing of memory-block number 2 has been inhibited (see Q.329) should it be possible to undo this with the password? The
allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
331 Inhibit reset of memory-block n. 2 ? - Should it be impossible to reset memory-block number 2 from panel?
See also Q.332. The allowed answer is either:
332 Enable reset of MB2 with password? - If the reset from panel of memory-block number 2 has been inhibited (see Q.331) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
Enable auto-advance of stat. memory? - Should the number of the statistics-memory advance automatically (instead of manually) during the reading-procedure ? The
333
allowed answer is either:
334 Divide income of mem.-block n. 2 by 100? - Should the income of memory-block n. 2 be divided by 100?
The allowed answer is either:
335 Hide on the Ticket the message "Thanks"?
336 Enable on the Ticket the 3 lines footer?
40
The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
IR SENSOR FOR PASSENGER DETECTION
0 (No: not present) or: 1 (Yes: present).
0 (No: normally open) or: 1 (Yes: normally closed).
0 (No: don't block) or: 1 (Yes: block).
0 (No: don't flash) or: 1 (Yes: flash).
from Q 316 / Available for any possible software extension / to Q 318
STATISTICAL MEMORY BLOCK N.1
0 (No: visualize) or: 1 (Yes: inhibit).
0 (No: print) or: 1 (Yes: inhibit).
0 (No: keep inhibited) or: 1 (Yes: enable with password).
0 (No: reset from panel) or: 1 (Yes: inhibit).
0 (No: access) or: 1 (Yes: no access).
ACCESS TO TARIFF PROGRAMMING
0 (No: also step by step) or: 1 (Yes: only memory-key).
STATISTICAL MEMORY BLOCK N. 2
0 (No: visualize) or: 1 (Yes: inhibit).
0 (No: print) or: 1 (Yes: inhibit).
0 (No: reset from panel) or: 1 (Yes: inhibit).
0 (No: manually) or: 1 (Yes: automatically).
0 (No: don't divide) or: 1 (Yes: divide).
PRE-PAID CARD
party is strictly prohibited.
Value
No / Yes
0 - 65535
No / Yes
0=open
1=closed
0 = registration
1 = pass to Hired
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes