Digitax F3 Plus Technical Manual page 37

Nr. Functions
220 Block-number for taxi-light to be ON: this is the number of the tariff-block where the taxi-light should be ON. The allowed value goes from 0 (min) to 62 (max).
221 Prog-Date-number for taxi-light to be ON: this is the number of the Prog-Date where the taxi-light should be ON. The allowed value goes from 0 (min) to 8 (max).
222 State of taximeter for taxi-light to be ON - This is the state (or states) of the taximeter in which the taxi-light should be ON.
The allowed values are:
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON the taxi-light in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
223 Enable light n. 1 ON in day-time? - Should it be possible for light number 1 to be ON during the day-time?
The allowed answer is either:
224 Light n. 1 must flash? - If Yes light number 1 will flash. The allowed answer is either: 0 (No: no flash) or: 1 (Yes: flash).
225 Light n. 1 must go ON in overspeed? - If Yes then light number 1 will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either: 0 (No: OFF) or: 1 (Yes: ON).
226 Light n. 1 must go on below overspeed?
230 Light n. 1 ON in this tariff-block? - With Yes light number 1 will go ON in the corrisponding tariff-block.
The allowed answer is either:
231 Block-number for light n. 1 ON: this is the number of the tariff-block where light number 1 should be ON.
The allowed value goes from 0 (min) to 62 (max).
232 Prog-Date-number for light n. 1 ON: this is the number of the Prog-Date where light number 1 should be ON.
The allowed value goes from 0 (min) to 8 (max).
233 State of taximeter for light n. 1 ON: this is the state (or states) of the taximeter in which the light number 1 should be ON.
The allowed values are:
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 1 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
234 Enable light n. 2 ON in day-time? Should it be possible for light number 2 to be ON during the day-time?
The allowed answer is either:
235 Light n. 2 must flash? - If Yes light number 2 will flash. The allowed answer is either: 0 (No: no flash) or: 1 (Yes: flash).
236 Light n. 2 must go ON in overspeed? - If Yes then light number 2 will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either: 0 (No: OFF) or: 1 (Yes: ON).
237 Light n. 2 must go on below overpseed?
241 Light n. 2 ON in this tariff-block? - With Yes light number 2 will go ON in the corrisponding tariff-block. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
242 Block-number for light n. 2 ON: this is the number of the tariff-block where light number 2 should be ON. The allowed value goes from 0 (min) to 62 (max).
243 Prog-Date-number for light n. 2 ON: this is the number of the Prog-Date where light number 2 should be ON. The allowed value goes from 0 (min) to 8 (max).
244 State of taximeter for light n. 2 ON: this is the state (or states) of the taximeter in which the light number 2 should be ON.
The allowed values are:
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 2 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
245 Enable light n. 3 ON in day-time? - Should it be possible for light number 3 to be ON during the day-time?
The allowed answer is either:
246 Light n. 3 must flash? - If Yes light number 3 will flash. The allowed answer is either: 0 (No: no flash) or: 1 (Yes: flash).
247 Light n. 3 must go ON in overspeed? - If Yes then light number 3 will go ON in case the actual velocity is higher than the velocity programmed in Q.200. The allowed
answer is either: 0 (No: OFF) or: 1 (Yes: ON).
248 Light n. 3 must go on below overspeed?
252 Light n. 3 ON in this tariff-block? - With Yes light number 3 will go ON in the corrisponding tariff-block. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
253 Block-number for light n. 3 ON: this is the number of the tariff-block where light number 3 should be ON. The allowed value goes from 0 (min) to 62 (max).
254 Prog-Date-number for light n. 3 ON: this is the number of the Prog-Date where light number 3 should be ON. The allowed value goes from 0 (min) to 8 (max).
The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
party is strictly prohibited.
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
0 (No: disabled) or: 1 (Yes: enabled).
from Q 227/ available for any possible software extension / to Q 229
0 (No: OFF) or: 1 (Yes: ON).
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
0 (No: disabled) or: 1 (Yes: enabled).
from Q 238 / available for any possible software extension / to Q 240
0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
0 (No: disabled) or: 1 (Yes: enabled).
from Q 249 / available for any possible software extension / to Q 251
LIGHT N. 1
LIGHT N. 2
LIGHT N. 3
Value
0 - 62
0 - 8
For Hire = 128
Stopped = 64
Hired = 32
None = 0
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
0 - 64
0 - 8
For Hire = 128
Stopped = 64
Hired = 32
None = 0
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
0 - 62
0 - 8
For Hire = 128
Stopped = 64
Hired = 32
None= 0
No / Yes
No / Yes
No / Yes
No / Yes
No / Yes
0 - 62
0 - 8
37