Summary of Contents for ARTRAY ARTCAM-0134AR-WOM Series
Page 1
November 12, 2020 Ver1.03 USB2.0 CMOS CAMERA SMALL TYPE ARTCAM-0134AR-WOM Series INSTRUCTION BOOKLET 1.2M pixels ARTCAM-0134AR-WOM Series ARTRAY CO., LTD.
1. Attention ■About this manual 1.Before using the camera, please read this manual thoroughly. 2.Please keep this manual reachable and always refer to the contents when needed. 3.Please contact us if the manual is lost or damaged. We will provide a replacement. 4.We cannot guarantee the safety of improper uses of the camera.
Page 4
■For Safe Use Warning ●In following circumstances, please stop using the product and turn off the power immediately to prevent the risks of fires and electric shocks. If the product is defective, please contact us for repair or exchange. For your safety, please do not disassemble, modify or repair the camera on your own.
Page 5
To save the environment, we do not issue warranty in printed format. Instead, all records of the warranty periods, delivery dates and the customer information are well kept in our system. For more details, please refer to the sites below: Hardware Warranty : http://www.artray.us/download/artray_warranty.pdf - 5 -...
2. Introduction ARTCAM-0134AR-WOM Series is CMOS cameras for industrial use. This series adopt USB2.0 interface, so the data can be delivered to PC directly without a capture board. Cameras are equipped with on board memory which avoid data missing during transfer.
Page 7
・Mirror function You can flip images vertically and horizontally by process of a sensor. ・Bounded Viewer Software We provide the Viewer Software - ART-Viewer (Windows 7/8/8.1/10). With this software, users can easily preview, save images and change camera settings. ・2D Measurement & Filing Software(Optional) Useful 2D measuring functions are available with the optional 2D Measuring &...
5. Connect the Camera 5-1 How to connect a camera 5-2 Shutter Speed Shutter speed can be changed on the standard viewer software ART-Viewer. The shutter speed is set directly on the sensor register, so please refer to the following formulas for the real exposure time.
6. Specifications 6-1 Color Model ARTCAM- 0134AR-WOM 0134AR-WOM-OP 0134AR-WOM-OP-CM Sensor Type CMOS Color Image Sensor Active Pixels 1280(H)×960(V) Active Imager 4.86(H)×3.66(V)mm Size 1/3” Scan Mode Progressive Scan Pixel Size 3.75(H)×3.75(V)μm Shutter Type Global Shutter Color Filter RGB Bayer Pattern Array Frame Rate 27.0fps Shutter Speed...
Page 11
6-2 Monochrome Model ARTCAM- 0134AR-BW-WOM 0134AR-BW-WOM-OP 0134AR-BW-WOM-OP-CM Sensor Type CMOS Monochrome Image Sensor Active Pixels 1280(H)×960(V) Active Imager 4.86(H)×3.66(V)mm Size 1/3” Scan Mode Progressive Scan Pixel Size 3.75(H)×3.75(V)μm Shutter Type Global Shutter Frame Rate 27.0fps Shutter Speed 1/26747~0.61s Interface USB2.0 Bulk Transfer Synchronization Internal Synchronization System...
Page 13
7-2 BOARD LENS, BOARD TYPE ARTCAM-0134AR-WOM-OP / 0134AR-BW-WOM-OP *Depending on different models, size and position of components in front of sensor board (condenser...) might vary. - 13 -...
9. Characteristic of visible light cut filter Near-infrared model (NIR) is adopting R70 on visible cut filter. Please check the spectral sensitivity characteristic of image sensor as well. - 16 -...
10. Optional Functions 10-1 Trigger timing chart Trigger Input TRIG Signal Reset Time Exposure Time Line Line Last Line Vertical Synchronization Signal Image Transfer (USB) Input Pulse Width Above 1ms Photo Coupler Delay 1~99μs (Subject to Input Pulse Voltage) Reset Time 320µs (Actual measurement value) Exposure Time Subject to Shutter Speed Settings...
10-2 GPIO GPIO option is available upon request before the delivery of the ARTCAM-0134AR-WOM series. Pin assign Function GPIO_0 GPIO_1 GPIO_2 VCC(3.3V) Maximum output 50mA GPIO_3 GPIO_4 GPIO_5 ・Each of the six GPIO pins is pulled up to 3.3V with 1kΩ on the circuit board and is connected to the IO pins on FPGA.
Page 19
What may cause the problem is that the regulation of the power lines becomes not enough, and so causes impudence mismatch on data signals. *For the recommended extension cable, please contact our sales department. (TEL: +81-3389-5488) ARTRAY CO., LTD. Obtained ISO 9001: 2015 2018/9/17 1-17-5 Kouenjikita, Suginami-ku, Tokyo 166-0002 Japan Tel:+81-3-3389-5488 Fax:+81-3-3389-5486...