Related Manuals for ARTRAY ARTCAM-407UV-WOM Series
Summary of Contents for ARTRAY ARTCAM-407UV-WOM Series
- Page 1 Apr 25, 2022 Ver1.02 USB2.0 Ultraviolet CCD CAMERA ARTCAM-407UV-WOM Series INSTRUCTION BOOKLET 1.5 M pixels ARTCAM-407UV-WOM Series ARTRAY CO., LTD. - 1 -...
-
Page 2: Table Of Contents
C-MOUNT, BOARD TYPE ......................- 11 - Spectral Sensitivity Characteristics ....................- 12 - 8.1. ARTCAM-407UV-WOM series ..................... - 12 - Ultraviolet (UV) Transmitting, Visible Absorbing Filter Characteristics ........- 12 - AD Conversion (ARTCAM-WOM series) ..................- 13 - 10.1. -
Page 3: Attention
1. Attention ■About this manual 1. Before using the camera, please read this manual thoroughly. 2. Please keep this manual reachable and always refer to the contents when needed. 3. Please contact us if the manual is lost or damaged. We will provide a replacement. 4. - Page 4 ■For Safe Use Warning ●In following circumstances, please stop using the product and turn off the power immediately to prevent the risks of fires and electric shocks. If the product is defective, please contact us for repair or exchange. For your safety, please do not disassemble, modify or repair the camera on your own. Please stop using the product and turn off the power immediately when: ・...
- Page 5 For more details, please refer to the following link: Hardware Warranty: http://www.artray.us/download/artray_warranty.pdf ●We do not guarantee the functions of this product or the descriptions on this manual to be completely adapted to the users’...
-
Page 6: Introduction
Camera image acquisition and camera control are possible with other applications is included as standard. You can also download it from the website below. http://www.artray.us/download_sdk.html ⚫ 2D Measurement & Filing Software(Optional) Useful 2D measuring functions are available with the optional 2D Measuring & Filing Software - ART-MEASURE. -
Page 7: The Product
4. The Product 1) Camera 2) USB2.0 Cable (Type A-B connector cable, 3m approx.) *A type-A connector (3m) is attached for an open frame model without USB connector. 3) Viewer software and Device driver CD <Option> 1) C Mount Lens 2) 2D Measurement &... -
Page 8: Specification
6. Specification 6.1. Specifications ARTCAM-407UV-WOM 407UV-WOM-OP 407UV-WOM-OP-CM Sensor Type CCD Monochrome Image Sensor Total Number Of Pixels 1434(H)×1050(V) Number Of Effective Pixels 1392(H)×1040(V) Resolution 1360(H)×1024(V) Active Imager 6.47(H)×4.83(V)mm Size 1/2” Scan Mode Progressive Scan Pixel Size 4.65(H)×4.65(V)μm Shutter Type Global Shutter Frame Rate 12fps Shutter Speed... -
Page 9: External Dimensions
7. External Dimensions 7.1. C-MOUNT, CASED, USB CABLE TYPE ARTCAM-407UV-WOM Drawing of the base without a tripod mount - 9 -... -
Page 10: Board Lens, Board Type
7.2. BOARD LENS, BOARD TYPE ARTCAM-407UV-WOM-OP - 10 -... -
Page 11: C-Mount, Board Type
7.3. C-MOUNT, BOARD TYPE ARTCAM-407UV-WOM-OP-CM - 11 -... -
Page 12: Spectral Sensitivity Characteristics
Spectral Sensitivity Characteristics 8.1. ARTCAM-407UV-WOM series Ultraviolet (UV) Transmitting, Visible Absorbing Filter Characteristics ARTCAM-407UV-WOM is adopting UV transmitting, visible absorbing filter U340. Please review the image sensor graph of wave length characteristic together for detailed information. *A model without filter is available. -
Page 13: Ad Conversion (Artcam-Wom Series)
AD Conversion (ARTCAM-WOM series) *AD conversion to 16 bit and then output the upper 10 bit to digital gain 10.1. Standard functions (configurable in standard viewer/SDK) ・Digital gain Global gain (digital gain) can be configured with the standard viewer software or SDK. Setting range on standard viewer software: 0 –... -
Page 14: Optional Functions
Optional Functions 11.1. Trigger Input ARTCAM-WOM series are designed with external trigger. Trigger Input Circuit Camera 3.3V FPGA TRIG PC814 R1 = 2.4kΩ R2 = 10kΩ 11.2. GPIO GPIO option is available upon request before the delivery of the ARTCAM-WOM series. Pin assign Function GPIO_0... - Page 15 ・Each of the six GPIO pins is pulled up to 3.3V with 1kΩ on the circuit board and is connected to the IO pins on FPGA. ・When GPIO pins are used as output pins, the FPGA output is driven at high impedance and Low level. (At the time of power-up: high impedance) To control GPIO, please use the ArtCam_SetIOPort / GetIOPort functions in SDK.
-
Page 16: Trigger Timing Chart
11.3. Trigger Timing Chart Trigger input pulse width 10 μs or more From the start of the trigger About 2 μs or less Internal trigger signal rise Internal trigger signal pulse width About 10 μs (fixed value) Shutter setting value * 1 line time Sensor pixel reset period (1 line time = 1790 * 1/24 [μsec]) Sensor exposure period... -
Page 17: System Requirements
System Requirements 12.1. Recommended System Requirements ●Host Controller This camera is applicable to USB 2.0. ●CPU The driver of this camera is applicable to computer architecture “x86” or “amd64”. The specification of CPU effects directly the imaging process speed, therefore it is highly recommended to utilize a high-end CPU if possible. - Page 18 ARTRAY CO., LTD. Obtained ISO 9001: 2015 2018/9/17 1-17-5 Kouenjikita, Suginami-ku, Tokyo 166-0002 Japan Tel: +81-3-3389-5488 Fax: +81-3-3389-5486 Email: sales@artray.us URL: www.artray. us - 18 -...
Need help?
Do you have a question about the ARTCAM-407UV-WOM Series and is the answer not in the manual?
Questions and answers