General Safety Information - Barmesa Pumps BSP-CCE Series Installation, Operation & Maintenance Manual

Before installation, read the following
instructions carefully.
follow instruction
information could cause serious
bodily injury, death and/or property
damage. Each Barmesa product is
carefully inspected to insure proper
performance. Closely following these
instructions will eliminate potential
operating problems, assuring years
of trouble-free service.
DANGER "Danger" indicates an
imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
"Warning" indicates
WARNING
an imminenty hazardous situation
which, if not avoided, MAY result in
death or serious injury.
CAUTION "Caution" indicates a
barmesapumps.com
potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
IMPORTANT! - Barmesa Pumps is not
responsible for losses, injury or
death resulting from failure to
observe these safety precautions,
misuse, abuse or misapplication of
pumps or equipment.
A L L R E T U R N E D
P R O D U C T S M U S T B E
CLEANED, SANITIZED, OR
D E CO N TA M I N AT E D P R I O R TO
SHIPMENT, TO INSURE EMPLOYEES
WILL NOT BE EXPOSED TO HEALTH
HAZ ARDS IN HANDLING SAID
MATERIAL. ALL APPLICABLE LAWS
AND REGULATIONS SHALL APPLY.
WARNING
Installation, wiring, and
j u n c t i o n c o n n e c t i o n s m u s t b e i n
accordance with the National Electric
Code and all applicable state and local
codes. Requirements may vary depending
on usage and location.
WARNING
Failure to servicing is to be conducted by
and safety
qualified personnel only.
power connected; the impeller can
cause serious injury.
may become entangled in moving
parts.
DANGER
before handling or servicing the
p u m p o r a n y a c c e s s o r y i t e m s
associated with or near the pump.
DANGER
human contact with pumped fluid.
DANGER
handling any aspect of the pumping
system. Lock out power and tag.
WARNING
pumps in water over 160º F. Do not
exceed manufacturers recommended
maximum performance, as this could
cause the motor to overheat.
DANGER
Heat build up on self-priming and end
suction pumps may cause dangerous
pressures. A high temperature switch
o r p r e s s u r e r e l i e f v a l v e i s
recommended to be installed in pump
case.
I n s t a l l a t i o n a n d
Keep clear of suction and
discharge openings. Do not
insert fingers in pump with
Always wear eye protection
when working on pumps. Do
not wear loose clothing that
Pumps build up heat
and pressure during
operation. Allow time
f o r p u m p s t o c o o l
T h i s p u m p i s n o t
i n t e n d e d f o r u s e i n
swimming pools or water
installations where there is
Risk of electric shock. To
reduce risk of electric shock,
always disconnect pump
from power source before
D o n o t u s e t h e s e
Operation against a
closed discharge valve
will cause premature
bearing and seal failure.

General Safety Information

WARNING
C a r e f u l l y r e a d
instruction manuals supplied with
motor or engine before operating or
servicing.
WARNING Pumps construc ted
w i t h o r f i t t e d w i t h
bronze/brass may contain
l e a d l e ve l s h i g h e r t h a n
considered safe for potable water
systems. Lead is known to cause
cancer and birth defects or other
r e p r o d u c t i v e h a r m . V a r i o u s
g o v e r n m e n t a g e n c i e s h a v e
determined that leaded copper alloys
should not be used in potable water
applications.
DANGER
These pumps are not to
be installed in locations
classified as hazardous in
accordance with the National
Electric Code, ANSI/NFPA 70.
IMPORTANT! - Prior to installation,
record Model Number, Serial, Amps,
Voltage, Phase and HP from pump
name plate for the future reference.
Also record the Voltage and Current
Readings at Startup:
Model Number: ____________________
Serial: ____________________
Amps:_______ Voltage:_______
Phase:_______ HP:_______
01