Table of Contents
Advertisement
Quick Links
6BSE-LDS /
6BSE-HLDS series
9, 12, 18, 24 & 30 HP @ 1150 RPM
barmesa.com
18, 24, 30, 36, 48 & 60 HP @ 1750 RPM
IMPORTANT! - Read all instructions in this manual before operating or servicing
a pump.
6BSE-LDS
9-30 HP
18-60 HP
Installation, Operation &
Maintenance Manual
Submersible Solids
Handling Pumps
6BSE-HLDS
30-60 HP
Last update: 10/08/2021
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Barmesa Pumps 6BSE-LDS Series
Summary of Contents for Barmesa Pumps 6BSE-LDS Series
- Page 1 Installation, Operation & Maintenance Manual Submersible Solids Handling Pumps 6BSE-LDS / 6BSE-HLDS series 9, 12, 18, 24 & 30 HP @ 1150 RPM barmesa.com 18, 24, 30, 36, 48 & 60 HP @ 1750 RPM 6BSE-LDS 9-30 HP 6BSE-HLDS 18-60 HP 30-60 HP IMPORTANT! - Read all instructions in this manual before operating or servicing a pump.
-
Page 2: General Safety Information
IMPORTANT! - Barmesa Pumps is not alarm that signals a malfunction of the swimming pools or water... -
Page 3: Specifications
Specifications DISCHARGE: 6", 125lb, flange horizontal. SPHERICAL SLD HNDLG: 3" LIQUID TEMPERATURE: 104° F (40° C) max. VOLUTE: Cast iron ASTM A-48 class 30. WEAR RING: Bronze. (Only for 6BSE-HLDS series) MOTOR HOUSING: Cast iron ASTM A-48 class 30. SEAL PLATE: Cast iron ASTM A-48 class 30. -
Page 4: Specifications And Dimensions
Specifications & Dimensions NEMA CORD CORD LOCKED CORD WEIGHT MODEL HP VOLTS PHASE (Nominal) AMPS ROTOR AMPS CODE SIZE TYPE O. D. (pounds) 6BSE30034HLDS 30 1750 1.34" 6BSE30044HLDS 30 1750 1.34" 6BSE36034HLDS 36 1750 1.34" 6BSE36044HLDS 36 1750 1.34" 6BSE48044HLDS 48 1750 1.34"... -
Page 5: Recommendations And Warnings
Recommendations and Warnings 4Receiving inspection 4 Installation 4Liquid Level Controls Upon receiving the pump, it should These pumps are recommended for The level control(s) should be inspected damage use in a sump, basin or lift station. mounted on the discharge piping, a shortages. -
Page 6: Installation & Service
Installation & Service IMPORTANT! - The overload will then These situations ma y induce a false signal in the moisture etecting automatically reset and start the circuit. If none of the above test pump up after the motor cools to a prove conclusive, the pump(s) should safe temperature. - Page 7 Service a) Inspect motor chamber for oil If oil is found to be clean and Use soap solution around the sealed Ÿ level and contamination. uncontaminated (measuring areas above the oil level and nspect b) Inspect impeller and body for above 15 V breakdown), re ill joints for "air bubbles".
- Page 8 Service 4Disassembly Motor and Bearings - Remove Apply adhesive compound to the Impeller and Volute - Disconnect shaft and press bearing (1 ) onto volute, impeller, seal plate and seal as power. Remove hex nuts ( ) and shaft, position squarely onto the previously stated and drain oil from vertically lift motor housing and seal shaft applying force to the inner race...
- Page 9 Service Thread cap screws (25) into bearing housing (15) and tighten. Refill chamber with oil. Conduit Box Assembly - Check power (38) and control cables (39) for crackes or damage and replace complete conduit box (4) if required. (See Figure 4) Bring motor wires through opening in top of motor housing (3), check sleeving and replace if damaged.
- Page 10 Service Wear Ring Apply retaining compound to the bore of volute (37) and press wear ring (33) into bore until seated. Impeller and Volute - Install impeller (32) by appling a thin film of oil to motor shaft and slide impeller straight onto shaft, keeping keyways lined up.
- Page 11 WAVE WASHER KEYWAY SUPPLIED SUPPLIED WITH MOTOR WITH MOTOR ROTOR MOISTURE SENSORS SEE DETAIL MECH. SEAL TEMP. & MOIST. WIRES NEUTRAL LINES WIRES MOISTURE SENSOR DETAIL STATOR...
-
Page 12: Parts List
Parts List 46BSE-LDS Item Part Number Description Qty. Material Motor 40040031 18 HP, 1750 RPM, three phase, 230/460 V 40040032 24 HP, 1750 RPM, three phase, 230/460 V 40040033 30 HP, 1750 RPM, three phase, 230/460 V 40040034 36 HP, 1750 RPM, three phase, 230/460 V Brand 40040035 48 HP, 1750 RPM, three phase, 460 V... - Page 13 Parts List 46BSE-LDS Item Part Number Description Qty. Material Impeller 03140053 18 HP, 1750 RPM, 9.50"Ø 03140053B 24 HP, 1750 RPM, 10.50"Ø 03140053C 30 HP, 1750 RPM, 11.00"Ø 03140053D 36 HP, 1750 RPM, 11.50"Ø 03140054 48 HP, 1750 RPM, 10.00"Ø Cast Iron 03140054B 60 HP, 1750 RPM, 11.00"Ø...
- Page 14 WAVE WASHER KEYWAY SUPPLIED SUPPLIED WITH MOTOR WITH MOTOR ROTOR MOISTURE SENSORS SEE DETAIL MECH. SEAL TEMP. & MOIST. WIRES NEUTRAL LINES WIRES MOISTURE SENSOR DETAIL STATOR...
- Page 15 Parts List 46BSE-HLDS Item Part Number Description Qty. Material Motor 40040033 30 HP, 1750 RPM, three phase, 230/460 V Brand 40040034 36 HP, 1750 RPM, three phase, 230/460 V 40040035 48 HP, 1750 RPM, three phase, 460 V 40040036 60 HP, 1750 RPM, three phase, 460 V 31020018 Bearing (Upper) Steel...
- Page 16 Parts List 46BSE-HLDS Item Part Number Description Qty. Material 30400315 Wear Ring Bronze 30400411 Impeller Washer SS 304 91010354 Screw Hex Head 5/8" 11UNC x 1½" SS SS 304 92010192 Volute Gasket # 51936 Rubber 03090063 Volute Cast Iron 31030006 Power Cable 3x2 # 37917 25 ft 30400904...
-
Page 17: Troubleshooting Chart
13. Piping attachments to building structure too loose or rigid NOTE: Barmesa Pumps assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Barmesa Pumps or its authorized service centers, automatically voids warranty. - Page 18 barmesa.com...
Need help?
Do you have a question about the 6BSE-LDS Series and is the answer not in the manual?
Questions and answers