MadStad Engineering MadStad Manual
Adjustable windshield system for ktm 1290 super duke gt
Hide thumbs
Also See for MadStad:
- Manual (10 pages) ,
- Installation instruction (2 pages) ,
- Manual (8 pages)
Advertisement
Quick Links
Adjustable Windshield System
KTM 1290 Super Duke GT
Please read this entire manual before proceeding with installation.
What is in the box:
(1) Base bracket
(2) Adjustable brackets
(1) Aluminum Crossbar
(4) M5 x 25 truss screws
(4) M5 metal flat washers
(6) M6 x 12 screws
(4) M6 metal flat washers
(4) M6 nylock nuts
(2) M6 split lock washers
(4) M5 Truss screws
(4) M5 flat plastic washers
(4) soft rubber washers
Advertisement
Related Manuals for MadStad Engineering MadStad
Summary of Contents for MadStad Engineering MadStad
- Page 1 Adjustable Windshield System KTM 1290 Super Duke GT Please read this entire manual before proceeding with installation. What is in the box: (1) Base bracket (2) Adjustable brackets (1) Aluminum Crossbar (4) M5 x 25 truss screws (4) M5 metal flat washers (6) M6 x 12 screws (4) M6 metal flat washers (4) M6 nylock nuts...
-
Page 2: Installation Overview
INSTALLATION OVERVIEW The MadStad system replaces the stock shield, stock adjustable bracket and attaches to the solid support structure beneath the instrument cluster. Before you begin installation, you must remove the factory windshield. It cannot be attached to the MadStad brackets. - Page 3 – Remove the four factory STEP 4 screws holding the instrument panel base to the bike. Pull this plastic base off carefully over the wiring harnesses. You WILL NOT be re- using these screws, but save them somewhere with the other bike parts being removed.
- Page 4 Then feed through the factory instrument panel bracket and set it on top of our base plate. Fasten down through both using the MadStad Phillips screws provided. Then re-attach the instrument panel.
- Page 5 The four indicated holes are where you will attach the MadStad adjustable brackets, to the outside of the mounting base. Use four M6 x 12 screws through the brackets then the...
- Page 6 – The windshield STEP 8 attaches to the four rubber well nuts on our adjustable brackets as shown at right. Use the four Phillips truss screws with plastic flat washers and rubber washers. Pre-install them onto the windshield as shown below before attaching the windshield to the brackets.
- Page 7 Adjusting the MadStad Brackets The knob screws release the brackets allowing the windshield to slide and tilt. These knob screws must always be tightened securely before riding. DO NOT attempt to adjust the brackets while riding! You must come to a complete stop before making adjustments.
- Page 8 Notes on Windshield Angle Most windshields work best when set at a 55-60 degree angle. We have provided an angle guide on the back page of this manual so that you can check and see if your shield is set somewhere in this range. To check your shield angle, your bike should be in an upright position either on a center stand or held up by a helper.
- Page 9 PIVOT SCREWS The MadStad mount has a pivot screw on each set of brackets, located near the center of the bottom bracket. A nylon lock nut keeps the screw snugly in place, yet allows the brackets to slide back and forth. It is adjusted at the factory to have a minimum of play yet still allow the brackets to move.
-
Page 10: Returns And Warranty
If you are not satisfied with your new windshield system you have 30 days to return it. Full details are available on our web site at www.madstad.com. If purchased from a dealer then please contact the dealer for their return policy. - Page 11 NOTES:...
- Page 12 MadStad Engineering, Inc. 1451 E. Jefferson Street Brooksville, FL 34601 U.S.A. Phone: 352-848-3646 Web Site: http://www.madstad.com Email: support@madstad.com Thank you for your support, and ride safely! April 30, 2018...