Advertisement
Mode
DEALER MODE
GLOBAL SETTINGS
The dealer sets the following
functions ON/OFF according to
the user's operating needs.
DTMF SET MODE
The dealer set the following
functions ON/OFF according to
the user's operating needs.
EXTENDED FUNCTION
MODE
CHANNEL SET MODE
The dealers use this mode to
set channel frequencies and
signaling according to the
user's operating needs.
WIRED CLONE MODE
WIRELESSCLONE MODE
Table 2.1 – Dealer Modes
2.1.3.1. Dealer Mode – Global Settings
To place the unit into the "Dealer Mode" for editing the global settings, do the following:
1. While pressing and holding the [LAMP] and [DIAL] buttons, switch the power "on". After
2 seconds the radio enters the dealer mode and "SEL" appears on the display.
2. While in dealer mode, press [SCN] to enter the global set mode.
Table 2.2 shows the function number and function options that can be selected while in this
mode. While in this mode, the Channel Selector knob is used to set functions "ON" or "OFF" or
to select the setting. After a function is set, pressing the [PTT] button stores the setting and
increments the menu to the next function option. Also, when the [PTT] button is pushed, a beep
will sound to confirm the setting.
Pressing the [SCN] button at any time while reviewing the function options will cause the unit to
exit the selection mode and revert back to the dealer mode screen. The current function option
will not be stored if it was changed. After the complete option list has been cycled through,
"End" will appear on the display. To exit dealer mode, cycle the power "off" and then back "on".
To review or confirm the function settings while in the DTMF set mode, press and hold the
[MONI] button and turn the channel select knob.
RELM Communications
Global Settings, DTMF Settings, Enhanced Global Settings, Channel Settings,
Wired Cloning, Wireless Cloning
1. Monitor 2. Scan 3. Dial 4. Talk Around 5. Low Power 6. Priority 7.Priority
Channel 8. Look Back A 9. Look Back B 10. Revert Channel 11.TX Scan Delay
12. Dropout Delay Time 13.Time Out Timer 14. Transmit Warning 15. TOT
Resume Time 16. TOT Reset Time 17. Squelch Level 18. Beep 19.Signalling 20.
Battery Save 21. Selectable CTCSS 22. Delete/Add 23. Test Mode
24. Digit Time 25. Inter Digit Time 26. First Digit Time 27. Rise Time 28. Rise
Time With CTCSS 29. PTT ID 30. Dial ID 31. Connect ID 32. Disconnect ID 33.
No. Of DTMF Keys 34. DTMF Hold Time 35. Store & Send 36.D Key Assignment
37. DTMF Signaling 38. Intermediate Code 39. Group Code 40. SQ. Auto Reset
Time 41.Call Alert/Transpond 42. Clear To Transpond
43. "A" Tone Duration 44. "B" Tone Duration 45. Gap Time 46. Auto Reset Time
47. Key 1, Key 2, Key 3, and Key 4 Assignment 48. Key 5 and Key 6 Assignment
1. Channel Selection 2. RX Frequency 3. RX Tone Signaling 4. TX Frequency 5.
TX Tone Signaling 6. DTMF/2-Tone Signaling 7. ANI ID Enable 8.Scan
Delete/Add 9. Busy Channel Lockout 10. Clock Frequency Shift 11.TX Power 12.
Bandwidth 13. DTMF ID Code Enable 14. Two-Tone Signaling
In this mode, data is copied from one radio to another through a cable.
In this mode, data is copied from one radio to another without cable by means of
the DTMF signaling.
Function
Page 9
Advertisement
