Table of Contents
Advertisement
Quick Links
HES
K100 Aperio
®
Wireless Cabinet Lock
Installation & Operating Instructions
Product Contents
A
Reader
B
Lock Body
C
Mechanical Key Override
D
Installation Template
E
Double Door Bracket
F
Strike Plate
G
Threadlock Pillow pack
H
2X AA Lithium Batteries*
* AA Lithium Batteries required. Use of other
types of batteries, such as Alkaline, will
significantly decrease battery life.
I
Hardware:
a. 2-56 X 7/16" 2x
b. 8-32 X 5/16"
c. 6-32 X 5/16" 3x
d. 6 X 1/2" 6x
e. 8-32" X 2-3/4" 2x
f. 8-32" X 1-3/4" 2x
g. 8-32" X 2-1/2" 2x
h. 8-32" X 3" Rod
i. 8-23 Nut
®
Diagram 1: Product Components
A
D
I: Hardware
a
b
c
d
B
E
G
e
f
g
C
F
H
i
h
1 of 12
Advertisement
Table of Contents
Related Manuals for Assa Abloy HES Aperio K100
Summary of Contents for Assa Abloy HES Aperio K100
- Page 1 K100 Aperio ® ® Wireless Cabinet Lock Installation & Operating Instructions Product Contents Diagram 1: Product Components Reader Lock Body Mechanical Key Override Installation Template Double Door Bracket Strike Plate Threadlock Pillow pack 2X AA Lithium Batteries* * AA Lithium Batteries required. Use of other types of batteries, such as Alkaline, will significantly decrease battery life.
-
Page 2: Recommended Tools
Recommended Tools • Flathead Drivers – 3/32", 3/16" • Drill & Drill Bits – 1 /16", 3/16", 1 /2" • Phillips Drivers – PO, P2 • Pencil • Wire Stripper • Level • Square • Ruler • Punch • Scissors Lock Orientation Options Diagram 2: Orientation Options Orientation A... -
Page 3: Product Specifications
Product Specifications • Wireless Frequency • HID multiCLASS SE technology ® ® Credentials Supported: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption • High Frequency (13.56 MHz): • Lock Battery Type AA Lithium, 1.5 Volts (V) » HID iCLASS ® • Battery Life 50,000 cycles* »... - Page 4 Prepping Diagram 3: Installation Template the Cabinet/ Drawer Face 1. Separate Strike Plate Template. 2. ESTABLISH CENTERLINE (for double door cabinet see Double Door Prepping, next page). 3. MEASURE cabinet wall thickness and mark offset line on face of cabinet/drawer. The offset line should match with the interior Strike Plate edge of the cabinet wall.
- Page 5 Double Door Diagram 5: Double Door Prep Prepping 1. Establish centerline on inside of stationary door. 2. Continue centerline onto outside face of cabinet. 3. Align offset line on template to the edge of the stationary door and align centerline above. Remove backing and apply template to cabinet face.
-
Page 6: Reader Installation
Reader Installation 1. ALIGN reader with mounting holes and 2. ADD Threadlock to threaded rod. pull cable through as shown. Trim the Secure Reader to cabinet/drawer threaded rod to length as outlined in using the cut threaded rod and Mounting Screw Length table on page 3. coupling nut. -
Page 7: Installation
Lock Body Diagram 8: Step 1 & 2 Installation 1. INSERT reader cable through hole in back of lock body. 2. ALIGN lock body to mounting holes and secure to cabinet/ drawer face using 2x screw f and 2x screw d. DO NOT over tighten. - Page 8 OPTIONAL Diagram 11: Mechanical Override Mechanical Override 1. SLIDE Override into slot as shown in Diagram 11. 2. ENSURE that override retracts latch bolt before installation. Override should rest loosely until lock body and battery cover are installed. Diagram12: Mechanical Key Override OPTIONAL Mechanical Key Override...
-
Page 9: Strike Plate Installation
Strike Plate Diagram13: Strike Plate Template Use Installation 1. ALIGN strike plate template to centerline and edge of cabinet. Drill mounting holes. 2. SECURE strike plate to inside cabinet wall using 2x Screw d, BUT DO NOT FULLY TIGHTEN. Adjust strike plate so the edge is flush with the cabinet wall edge then tighten. -
Page 10: Led Codes
Aperio Hub Specifications • Approvals CE, ETL, FCC, IC, C-Tick • Radio Standard IEEE 802.15.4(2.4GHz) – 15 channels (11-25) • Safety & Emissions • Encryption (RadioCommunications) FCC 47CFR Part 15 subpart B and subpart C; IC RSS-210 EN ETSI 301 489-17 v2.1.1; ENETSI AES 128 bits 300 328 v1.7.1;... -
Page 11: Connecting The Hub
Connecting the Hub The following applies only to Aperio factory paired kits with AH20 Hubs. 1. Connect the Wiegand D1, D0, red, and green LED signals. NOTE: The Green LED input is used to grant access to the cabinet lock. If the Green LED signal is not available to indicate approved access, the approval input can be activated by a relay with “NO”... - Page 12 WARNING Conformité aux normes FCC Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B, conformément à la Partie 15 des règlements de la FCC. FCC Statement Ces limites sont conçues pour fournir une protection This equipment has been tested and found to comply raisonnable contre les interférences nuisibles dans une with the limits for a class B digital device, pursuant to part...